Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Earbrass on September 20, 2012, 03:18:13 PM
-
What sort of tape should one use for blocking off a note? I was thinking masking tape, as it would be easy to remove later and shouldn't leave residue - is that a good choice?
I ask because my bandmate's Lilly has developed an occasional fault whereby one of the squeaky-end treble notes sticks on, so that it sounds without the button being touched. Bad news in the middle of a performance. Until such time as it can be seen by someone who really knows what they are doing, I suggested taping off that note (it's not one that is ever played on purpose). Good idea?
All advice gratefully received.
-
I was advised to use blue painter's tape when I taped off the thirds on my LH chords. It was simple enough and has been working pretty well so far.
-
Scotch magic tape has the best long term performance I've found and leaves little residue even after years. Masking tape is only designed for temporary use and can be hard to remove after a long period.
-
Oops - Gaffer tape wasn't a good option on my Black Pearl III then......... ;D
-
Oops - Gaffer tape wasn't a good option on my Black Pearl III then......... ;D
Well it didn`t do the bellows any harm ::) ;D
-
Is it an option to stop that button moving and so prevent the air flow. Just feels a bit better to have something easily removable such as a thick piece of foam rather than a piece of tape which could be the source of problems later?
John
-
Thanks all.
-
Scotch magic tape has the best long term performance I've found and leaves little residue even after years. Masking tape is only designed for temporary use and can be hard to remove after a long period.
Hmm... maybe I should replace my tape with scotch while the tape is still new.
-
TO be honest, I`d fix the box, take the grille off and have a look what`s causing the issue . the Lily uses the standard (and ancient) "Matchstick and coathanger" lever/pallet-rod system (nothing complicated) so it should be easy to locate what`s jamming or sticking, it could be a damaged pallet facing causing the note to sound, at worst a swolen lever which could be tricky.
I got a fixer-upper Hohner Club recently and someone had jammed a cork in the offending hole behind the pallet of a note where the reed was out of tune and stuck the pallet back with chewing gum - LOL, looks like it was done in the 50s or 60s . (I removed the cork and tuned the reed, used new Chewing gum of course, I didn`t re-chew the old stuff ;D) .
Pic found on internet detailing lever system
-
In the past I have found it useful to stop out of tune reeds from sounding on my one row four stop by shutting the stop on the offending reed and pushing a piece of screwed up paper into the hole under the pallet. The solution is quick and easy to apply and is easy to remove when a full repair is convenient
-
TO be honest, I`d fix the box, take the grille off and have a look what`s causing the issue . the Lily uses the standard (and ancient) "Matchstick and coathanger" lever/pallet-rod system (nothing complicated) so it should be easy to locate what`s jamming or sticking, it could be a damaged pallet facing causing the note to sound, at worst a swolen lever which could be tricky.
On the contrary it can sometimes be very tricky and frustrating to fix sticking keys on this type of mechanism. It is certainly worth checking that the pallet is closing over the hole, and is not catching on anything. Anything else usually means pulling out the axle rod to remove the keys and investigate the cause. The axle rod itself is sometimes the problem. A slight roughness on the surface of the metal that can be enough. If the lever is tight proceed with caution on any attempts to ease the tightness. The last thing you want to end up with is a lever that is too loose and a button that wobbles as you press it.
-
I wish they`d use Metal levers like some Heligonkas (late Delicias etc) have , no swelling or splitting where the button screws go in . I remember that Carnival someone posted a pic of where he`d knocked the end button and split the wood.
-
I wish they`d use Metal levers like some Heligonkas (late Delicias etc) have
Oh! and all the Hohners I've ever seen ;)
-
the Delicia Gonks (such as later models which have this system) use the same design as the Lily etc but the button levers are either aluminium or stainless steel (dunno which as they`re painted and I`m not scraping paint off a near mint box to find out :P. )
-
I wedge a small piece of paper in the reed. No chance of leaving any residue, and very easy to remove.