Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: deltasalmon on June 08, 2013, 02:48:29 PM

Title: Bellows Pin Remover
Post by: deltasalmon on June 08, 2013, 02:48:29 PM
Does anyone here sell a bellows pin remover tool? I'm not sure what the official name for it is but if anyone has one they want to sell please PM me.

Cheers,
Sean
Title: Re: Bellows Pin Remover
Post by: Theo on June 08, 2013, 03:34:07 PM
A pair of end cutters does a good job.
Title: Re: Bellows Pin Remover
Post by: squeezy on June 08, 2013, 04:13:07 PM
Absolutely agree with Theo - and as you don't want them for their cutting ability go for the cheapest you can get ... I use these: http://www.amazon.co.uk/dp/B001C7HJ4U/?tag=hydra0b-21&hvadid=9550950909&ref=asc_df_B001C7HJ4U

I've modified them by filing a hole about the dimensions of a standard Italian bellows pin shaft in the middle using a cheap needle file.  Other improvements can be made by blunting the cutting edge using a straight file before filing the hole - and glueing a soft thin material (leather) to the part of the tool that is going to come in contact with the instruments it is repairing which reduces the risk of scratching.

Cheers

Squeezy
Title: Re: Bellows Pin Remover
Post by: deltasalmon on June 08, 2013, 04:19:56 PM
Shipping on that one to the States is quite expensive but I'm sure I can find an equivalent on the .com version of the website.

Thanks!
Title: Re: Bellows Pin Remover
Post by: syale on June 08, 2013, 04:36:04 PM
You can buy one at Harbor Freight for $2.50: http://www.harborfreight.com/4-inch-end-nipper-pliers-39531.html (http://www.harborfreight.com/4-inch-end-nipper-pliers-39531.html)
Title: Re: Bellows Pin Remover
Post by: Graham Spencer on June 08, 2013, 04:38:05 PM
Shipping on that one to the States is quite expensive but I'm sure I can find an equivalent on the .com version of the website.

Thanks!

In my experience boot sales, flea markets & pound shops (I assume there's a US equivalent of these) as well as the cheap supermarket chains like Lidl and Aldi usually have plenty of cheap sets of small pliers including end-cutters which will serve the purpose admirably - and you get some useful small pliers as well.  The ones I use came from Aldi - 6 assorted pliers/cutters for a couple of quid.

Graham
Title: Re: Bellows Pin Remover
Post by: Adam-T on June 08, 2013, 04:38:27 PM
Thanks - Just ordered a pair - I`ve been using regular side cuts and a piece of plastic card to protect the finish
Title: Re: Bellows Pin Remover
Post by: Owen Woods on June 08, 2013, 05:55:46 PM
Be careful of side cutters, as they might have a ridge on them which will damage the finish. I bought a pair and pulled out all of the bellows pins on one side of my Saltarelle before I noticed :(
Title: Re: Bellows Pin Remover
Post by: Graham Spencer on June 08, 2013, 07:22:35 PM
Yes, an efficient pair of end cutters will neatly snip off your bellows pins leaving you with a major problem - which is why Squeezy suggests filing a notch in them to fit round the average pin.  In the cheapie stuff we're talking about here, though, there's every chance the metal of the pins will be harder than that of the cutters! Having said that, I would have thought it only common sense to examine the tool you've acquired and try to ensure it will do no damage to your pins before using it - and of course, apply only the minimum pressure required to get the pin moving.
Title: Re: Bellows Pin Remover
Post by: Prestidigitator on June 08, 2013, 09:47:44 PM
Try jewellery pliers, which have plastic faced jaws. There are lots on EBay.

I also use Maun end-cutters. I notch them per Squeezy,  file off the cutting edge, and install a threaded and adjustable stop, which I adjust to the pin shank diameter and which stops the tool from being closed too tight and marking or spoiling the pin.

Personally, I've found that a lot of thought, much trial and error, but very little investment, has resulted in a set of tools that do precisely what I want.
Title: Re: Bellows Pin Remover
Post by: Steve C. on June 09, 2013, 01:27:36 AM
Another good tool for the job is what we in the States call a "trim tool" which is used for prying off the interior door upholstery on most autos.

The one on the top generally works best if you can find a set of "1".

http://www.crutchfield.com/p_126CR3NGL/Bojo-Trim-Panel-Tools.html?tp=990&awkw=19884656305&awat=pla&awnw=g&awcr=15802862185&awdv=c
Title: Re: Bellows Pin Remover
Post by: Lester on June 09, 2013, 10:35:08 AM
Another good tool for the job is what we in the States call a "trim tool" which is used for prying off the interior door upholstery on most autos.

The one on the top generally works best if you can find a set of "1".

http://www.crutchfield.com/p_126CR3NGL/Bojo-Trim-Panel-Tools.html?tp=990&awkw=19884656305&awat=pla&awnw=g&awcr=15802862185&awdv=c

Any tool, such as this, that requires you to pivot on the casework to lift the pin is, in my opinion, a bad thing. Pliers that allow you to draw the pin out with no contact on the casework are far safer.

I also recommend covering the pin with some rag before grasping it with the pliers to protect both the pin and the casework.
Title: Re: Bellows Pin Remover
Post by: Steve_freereeder on June 09, 2013, 10:52:42 AM
Another good tool for the job is what we in the States call a "trim tool" which is used for prying off the interior door upholstery on most autos.

The one on the top generally works best if you can find a set of "1".

http://www.crutchfield.com/p_126CR3NGL/Bojo-Trim-Panel-Tools.html?tp=990&awkw=19884656305&awat=pla&awnw=g&awcr=15802862185&awdv=c

Any tool, such as this, that requires you to pivot on the casework to lift the pin is, in my opinion, a bad thing. Pliers that allow you to draw the pin out with no contact on the casework are far safer.
I agree. A lever-type tool also has the effect of pulling out the pin in a curved path which can risk (a) bending of thin pins and (b) elongating the pin holes to an elliptical shape. A straight pull out, along the axis of the pin is what you should aim for.

Quote
I also recommend covering the pin with some rag before grasping it with the pliers to protect both the pin and the casework.
Yes, I use a scrap piece of thin chamoix leather for this purpose.
Title: Re: Bellows Pin Remover
Post by: Steve C. on June 10, 2013, 04:15:50 AM
Well, yes, I agree with the side cutters, that's what I always used.  Also needle-nose pliers.
And yes, padding out/protecting with chamois or similar.
What is nice about trim tools are that they are often polycarbonate and relatively soft/non-maring, especially with added chamois, etc.
Agree: the straightest pull is the the goal (along with not damaging the casework, scratching the pin, etc.
Might also add to this thread:  always use a pin block, foam block or similar to be sure to put the same pin back in the hole it came out of.
Some boxes (many?) have quite irregular pins/pinholes, and putting the same pin back in the same hole is important.
Title: Re: Bellows Pin Remover
Post by: Kimric Smythe on July 02, 2013, 10:03:48 PM
PM me if you still need one. I make them out of end nippers. The face is ground and polished to prevent scratches on the instrument ,and the jaws are ground and altered to pull pins without cutting or gouging them.
Title: Re: Bellows Pin Remover
Post by: deltasalmon on July 03, 2013, 03:10:31 AM
PM me if you still need one. I make them out of end nippers. The face is ground and polished to prevent scratches on the instrument ,and the jaws are ground and altered to pull pins without cutting or gouging them.

I'm in the process of doing this. I filed a hole in the edge and am going to grind and polish it flat. Thanks for the offer though.
Title: Re: Bellows Pin Remover
Post by: ButtonBox21 on July 04, 2013, 12:12:52 PM
Just a thought, have you talked to a technician at an accordion dealer/repair shop as to what they use to remove pins. I have seen a tool that looks like a screwdriver with a small claw on the end. I don't know what it is called but it worked very well and didn't leave scratches. I am sure a dealer/repairer would be happy to assist you.  :||:
Title: Re: Bellows Pin Remover
Post by: Theo on July 04, 2013, 12:26:15 PM
Just a thought, have you talked to a technician at an accordion dealer/repair shop as to what they use to remove pins.

Several have already responded.

Hohner sell Bellow pin pliers part number TA18010 price €141.60.
Title: Re: Bellows Pin Remover
Post by: Bill Young on July 04, 2013, 12:33:28 PM
I have seen a tool that looks like a screwdriver with a small claw on the end. I don't know what it is called but it worked very well and didn't leave scratches.
That is a tack lifter (http://www.amazon.co.uk/Draper-64804-195-Tack-Lifter/dp/B0001K9ZAK). The one sold by B&Q comes on a card which is handy for putting under the tool to protect the accordion surface.
Title: Re: Bellows Pin Remover
Post by: Lester on July 04, 2013, 12:39:28 PM
I have seen a tool that looks like a screwdriver with a small claw on the end. I don't know what it is called but it worked very well and didn't leave scratches.
That is a tack lifter (http://www.amazon.co.uk/Draper-64804-195-Tack-Lifter/dp/B0001K9ZAK). The one sold by B&Q comes on a card which is handy for putting under the tool to protect the accordion surface.

No! you will damage the casework eventually and probably sooner than that.
Title: Re: Bellows Pin Remover
Post by: Steve_freereeder on July 04, 2013, 12:59:34 PM
I have seen a tool that looks like a screwdriver with a small claw on the end. I don't know what it is called but it worked very well and didn't leave scratches.
That is a tack lifter (http://www.amazon.co.uk/Draper-64804-195-Tack-Lifter/dp/B0001K9ZAK). The one sold by B&Q comes on a card which is handy for putting under the tool to protect the accordion surface.

No! you will damage the casework eventually and probably sooner than that.
Totally agree with Lester. Don't use these things! Reasons already given earlier in this thread. You need a tool such as pliers or end cutters which will allow you to give a straight upwards pull. Also use cloth or chamois leather to protect the casework.
Title: Re: Bellows Pin Remover
Post by: Bill Young on July 04, 2013, 01:05:04 PM
Disagree with both of you. Have you tried one at all? The variable radius on the end of the tool gives a lift at right angles to the surface.
Title: Re: Bellows Pin Remover
Post by: Lester on July 04, 2013, 02:27:00 PM
Disagree with both of you. Have you tried one at all? The variable radius on the end of the tool gives a lift at right angles to the surface.

Feel free to disagree, but the pliers method puts no pressure on the casework at all whereas the tack lifter does and therefore can/may damage the casework.
Title: Re: Bellows Pin Remover
Post by: Graham Spencer on July 04, 2013, 03:06:10 PM
Disagree with both of you. Have you tried one at all? The variable radius on the end of the tool gives a lift at right angles to the surface.

Feel free to disagree, but the pliers method puts no pressure on the casework at all whereas the tack lifter does and therefore can/may damage the casework.

Absolutely right. Modified/blunt end-cutters are definitely the way to go.

Graham
Title: Re: Bellows Pin Remover
Post by: Christopher K. on July 06, 2013, 09:10:55 AM
I have end cutters with the jaws dulled by a file, and a scrap of leather like Steve uses. They work nicely for <$3. Formerly, I used a nail clipper with similarly modified jaws. Handy for the pocket but difficult to manipulate.

I'll second that recommendation of Harbor Freight for anyone who lives in the US.... well, for some things, anyway. We actually have a brick and mortar HF in our town. It's filled with diverse stuff of Chinese origin that doesn't have to be expensive to be functional. Like nylon rope, buckets, trash bags, primer, and hardware.
SimplePortal 2.3.5 © 2008-2012, SimplePortal