Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: syale on August 17, 2013, 02:17:30 AM
-
Can you wax reeds in by placing strips of wax alongside the reeds and playing a heat gun over the wax to melt it ?
-
I doubt if the vinyl / vileda valves would survive the heat
help operator, give me the number for 911 ....
-
Placing a bad heat conductor over the reed blocks would go some way to stop the heat getting to the valves and directional nozzles on the heat gun would also help?
-
There's too many better ways to do it. I melt it in a jar in hot water and use an eyedropper to pour it between the reeds.
-
wouldn't the passing hot-air also tend to blow the melting wax along / away from the reed plates
why not use the tools the makers and repairers have used for years ?
-
Placing a bad heat conductor over the reed blocks would go some way to stop the heat getting to the valves and directional nozzles on the heat gun would also help?
it`d stop it getting to the wax too . Inventive, but you`re complicating things too much here ::) .
Also I know if I tried the eyedropper method, the dropper would clog up and get messy (and it`d take me hours) , I`ll stick to the amateur method of temp controlled soldering iron and wax sticks - the Pros can mess with burners, wax pots, spoons and spatulas
-
I am a complete amateur in this, but when I have turned plates … I cut lttle strips of wax with
scalpel (bugger, son's nicked that) Stanley knife, and quickly run past them with my soldering iron (double bugger!) a heated skewer.
Seems to work. In extremis (when son aged 3 kicked melodeon off shoulder) I once used penknife, tent peg and primus stove for the necessary repair.
Though it might have been easier to stop at 2 daughters ;)
-
I am a complete amateur in this, but when I have turned plates … I cut lttle strips of wax with Stanley knife, and quickly run past them with my heated skewer.
Seems to work. In extremis (when son aged 3 kicked melodeon off shoulder) I once used penknife, tent peg and primus stove for the necessary repair.
You really have been hanging around with Pikey too long haven`t you - LOL ;D .. at least you`ve not resorted to carpet tape and matchsticks :o
-
Although not an expert on reeds, I am however an expert on glue. Although this applies to books the principle is the same.
Stick (pun) with the traditional methods. I'm not a Luddite but a hundred years of trying the best method of waxing to my mind has been perfected. It's a bit like the Angle Poise lamp invented in the 1920's and never been bettered. (:)
-
I am a complete amateur in this, but when I have turned plates … I cut lttle strips of wax with scalpel (bugger, son's nicked that) Stanley knife, and quickly run past them with my soldering iron (double bugger!) a heated skewer.
Seems to work. In extremis (when son aged 3 kicked melodeon off shoulder) I once used penknife, tent peg and primus stove for the necessary repair.
Though it might have been easier to stop at 2 daughters ;)
Is there a Boy Scout badge for Mobile Melodeon Maintenance? If so, you certainly qualify.
-
I am a complete amateur in this, but when I have turned plates … I cut lttle strips of wax with scalpel (bugger, son's nicked that) Stanley knife, and quickly run past them with my soldering iron (double bugger!) a heated skewer.
Seems to work. In extremis (when son aged 3 kicked melodeon off shoulder) I once used penknife, tent peg and primus stove for the necessary repair.
Though it might have been easier to stop at 2 daughters ;)
Never heard of a "two daughter stop" does that remove the third?
Or indeed add one or two?
-
I don't think you can narrow the 'flame' enough. Plus you don't actually need much heat, there's a big risk you'll melt the wax too much, and even set it alight !
Use Charlie marshalls method, it's easy and it works,
Get an artists brush, flat head about 6mm wide, melt the wax in a pan ( I use an old milk pan ), place the reed on the wood, dip the brush in the wax, and flow it into the corner between the reed and the wood. Do the rest of the reed in the same way, then go round and do it again.
I think Charlie's get a video on YouTube somewhere, just search for Reed Waxing.
Alternatively, if its only one reed that needs putting back in, I've used a flat screwdriver blade, heated over a gas ring (gently heated, not until it goes blue!), then gently pressed the wax in place.
-
Alternatively, if its only one reed that needs putting back in, I've used a flat screwdriver blade, heated over a gas ring (gently heated, not until it goes blue!), then gently pressed the wax in place.
So convergence of technique there, though (honest) I only met Pikey at Bob's Swaledale tunes weekend last year! I take it a bit hotter, and actually melt in the wax. Sounds fiddly, but you have very good control of things and very little kit is needed.
Perhaps as well as my toolkit is now empty :-\ Just discovered all my suitcases are missing too :o
-
scalpel (bugger, son's nicked that) soldering iron (double bugger!)
I know that tune very well...... (:)
-
I confess to using the wax that cheeses get wrapped in for emergency repairs. ;)
-
Also I know if I tried the eyedropper method, the dropper would clog up and get messy (and it`d take me hours) ,
There's definitely a couple tricks to keeping it from clogging, I like the fact you have pinpoint control. We all have our comfort spots.
-
why not use the tools the makers and repairers have used for years ?
Because then nothing would ever progress? Then again, I have to agree with people's analysis here on this particular idea!
There are so many different ways of doing this particular job. I think that for standard boxes, the encaustic stylus has much to recommend itself, especially for quick and dirty jobs. But there are so many different options. Olav seems to get fantastic results with his folded brass spoon.
-
Now about this acetylene torch idea I've been toying with......... >:E ;D
-
I confess to using the wax that cheeses get wrapped in for emergency repairs. ;)
Yeah - BabyBel-Tuna ..... ;D
-
why not use the tools the makers and repairers have used for years ?
Because then nothing would ever progress? Then again, I have to agree with people's analysis here on this particular idea!
There are so many different ways of doing this particular job. I think that for standard boxes, the encaustic stylus has much to recommend itself, especially for quick and dirty jobs. But there are so many different options. Olav seems to get fantastic results with his folded brass spoon.
I agree to a certain extent, but if the wax hasn't changed why should the method.
Now for the Thermic Lance.
-
I confess to using the wax that cheeses get wrapped in for emergency repairs. ;)
… that trumps us all, frankly ::)
-
I confess to using the wax that cheeses get wrapped in for emergency repairs. ;)
Yeah - BabyBel-Tuna ..... ;D
Lol
-
Now about this acetylene torch idea I've been toying with......... >:E ;D
Recommended for rereeding piano accordions......
-
Now about this acetylene torch idea I've been toying with......... >:E ;D
Recommended for rereeding piano accordions......
I wish I wasn't drinking something when I read that. ;D
-
Now about this acetylene torch idea I've been toying with......... >:E ;D
Recommended for rereeding piano accordions......
I wish I wasn't drinking something when I read that. ;D
>:E
-
Now about this acetylene torch idea I've been toying with......... >:E ;D
Recommended for rereeding piano accordions......
De-Reeding Piano accordions certainly ---- the only prob is what to do with the reeds, I mean it`d take forever to find a use for over 300 Gleichtons .....
-
Although not an expert on reeds, I am however an expert on glue. Although this applies to books the principle is the same.
Stick (pun) with the traditional methods. I'm not a Luddite but a hundred years of trying the best method of waxing to my mind has been perfected. It's a bit like the Angle Poise lamp invented in the 1920's and never been bettered. (:)
has anyone re-invented the wheel :-\
-
Although not an expert on reeds, I am however an expert on glue. Although this applies to books the principle is the same.
Stick (pun) with the traditional methods. I'm not a Luddite but a hundred years of trying the best method of waxing to my mind has been perfected. It's a bit like the Angle Poise lamp invented in the 1920's and never been bettered. (:)
has anyone re-invented the wheel :-\
Maglev?
http://news.bbc.co.uk/2/hi/9617577.stm (http://news.bbc.co.uk/2/hi/9617577.stm)
-
Maglev
yes, I experienced the ride at 304kph at Shanghai in Sept 2012, 100Yuan (~$15) return ticket