Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Rog on October 16, 2013, 07:34:30 AM
-
A subject that has been covered ad nauseum...
I've seen Nick Collisbird's vid on how to make leather diamonds/gussets for the diamond shaped hole where the card meets on homemade bellows ( for his Chanson).
I am rebuilding one of those crappy German boxes with brass reeds, just to prove I can bring it back to life &c. It's largely a pile of firewood so I'm glueing it back together at the moment.
The bellows aren't too bad but there are one or too little holes right on the very apex of some corners just above the little leather gussets. I'm thinking of using little bits of very thin leather glued from inside, but is there a better way? BTW the bellows don't have any tape on the edges, AFAICT.
-
The bellows aren't too bad but there are one or too little holes right on the very apex of some corners just above the little leather gussets. I'm thinking of using little bits of very thin leather glued from inside, but is there a better way?
That's exactly the way in which Dave Elliott, the highly respected concertina repairer/restorer repaired the bellows of my Wheatstone English concertina a few years ago. Thin (0.2 mm) leather for repair/binding is available from Mark Adey concertina spares (formerly David Leese) here (http://concertina-spares.com/spareslist.htm) (scroll down the list).
Use PVA glue diluted 50/50 with water. Apply to the leather patch and press into place from the inside of the bellows using a blunt lolly stick or similar. Wipe off any excess glue which oozes out with a damp cotton bud.
-
Use PVA glue diluted 50/50 with water.
Better still use the correct glue for the job leather cement (http://www.leprevo.co.uk/photos/leathercraft-cement.htm) easier to use, and stronger bond on leather than pva.
-
Use PVA glue diluted 50/50 with water.
Better still use the correct glue for the job leather cement (http://www.leprevo.co.uk/photos/leathercraft-cement.htm) easier to use, and stronger bond on leather than pva.
Just reporting on what Dave used...
-
Use PVA glue diluted 50/50 with water.
Better still use the correct glue for the job leather cement (http://www.leprevo.co.uk/photos/leathercraft-cement.htm) easier to use, and stronger bond on leather than pva.
I don't know about leather cement, in fact never heard of it. But if Theo recommends it then I'm sure it will be fine.
-
http://leatherworker.net/forum/index.php?showtopic=36923
Small worlds… with luck someone at leatherworker.net might even link back here! ;)
-
I use the same method with small pieces of thin leather. The right sort of leather can often be had for free by putting the word out that you would be grateful for odd ladies gloves which usually get shoved in a drawer when t'other one is lost! Ladies glove leather is ideal and just one glove will provide several patches. Recycling at its best!
george
-
Hi all,
Great. I'm on the right track then. I was also impressed by Nick's leather paring/skiving and in the interests of keeping the costs down I bought a big bag of assorted leather off cuts (eBay, £8) so all I need to do is pare off some thin patches. However, I like the idea of old ladies gloves (i know i know grammatical ambiguity) I'll look in charity shops for these. I may try PVA to start as I've already forked out a few quid for materials. However I'll keep a lookout for leather cement. I'll keep you posted on progress.
-
Bearing in mind that these bellows are really shot to pieces, so anything I do to them is purely to try stuff out.... I didn't want to use my PVA wood glue or the Bostick Impact adhesive, so I've stuck a couple of patches on using Copydex, which seems to work fine. Any reason why this might be a bad idea?
Btw they are taped, so might have to replace this; Gorilla gaffer tape probably would not look v nice ;)
-
Roger, don't use Copydex. After a month or two it becomes a horrible sticky mess.
Bit like me after a folk festival :-X
-
Roger, don't use Copydex. After a month or two it becomes a horrible sticky mess.
Bit like me after a folk festival :-X
Oh. Damn. The bellows really are full of holes though. Did you use PVA when sticking leather onto your bellows?
V good learning process this. First thing to do when fixing up a box is to stop it leaking, starting with the bellows, and if they are useless there's no point in going further until you solve that problem one way or another.
I think I'll follow Theo's advice and get some leather cement.
-
Wonder if the thought process differs for an "old dog" or a "decent" box.
I would have looked at the reeds first, because if it uses long reed plates they could be hard to replace if knackered.
Then looked at the woodwork to check it wasn't twisted or inhabited.
(You have probably already done that, though).
If the economics permit, you can get bellows made.