Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: IvanM on June 16, 2014, 04:41:32 PM
-
How do you clean green oxide of copper (don't know how it's properly called, I'm not a chemist; verdigris?) and simple rust from metallic parts? I'm not saying about rusty reeds (thank Apollo!), but mechanics etc. I can leave it alone but...
-
As far as green copper oxide is concerned, a mild acid such as vinegar or lemon juice should help. However, it does depend on whereabouts in the box it is, how easy it is to get at and remove excess acid from, and what;s right next to it that might be adversely affected by the acid.
Red iron oxide (aka rust) is less easy; you might be able, again depending on the exact parts involved, to use a chemical preparation that converts red iron oxide to black iron oxide; otherwise it's down to the careful use of gentle abrasives. There must be the odd metallurgist (actually, pretty well all the metallurgists I know are fairly odd!) on here who can give you more detailed advice......
Graham
-
Rust removal? try "Evapo-rust", It works great for me, even does reeds, just soak the metal in the stuff for an hour or two. Its water-soluble, Non-toxic, non-corrosive and biodegradable. safe even in your eyes [if you have rusty eyes]. It just does exactly what it says on the plastic bottle. had to get my small bottle [32 fl. oz.]
-
Ah yes forgot to say had to get it from the states, via ebay.
-
as far as cleaning rusty reeds, I've been told that soaking them in petrol for a few hours works wonders!
-
as far as cleaning rusty reeds, I've been told that soaking them in petrol for a few hours works wonders!
I've used white spirit and meths to remove grease, old wax and general crud, but I'm not sure what effect they or petrol would have on rust.
-
as far as cleaning rusty reeds, I've been told that soaking them in petrol for a few hours works wonders!
Certainly does not work on steel petrol tanks.
-
I use one of these for cleaning the top side of reeds:
http://www.maplin.co.uk/p/abrasive-polishing-block-hx04e (http://www.maplin.co.uk/p/abrasive-polishing-block-hx04e)
Oddly I have found the rust on the underside of reeds is much looser and can be removed by gentle scraping, otherwise some 240 grit silicon abrasive paper under the tongue will sort it out.
-
On the same subject, what is the best way to clean up a rusty grille? I have a couple of old Hohners with this condition. One is a Double Ray Deluxe, with a pressed chrome grille. Theo has mentioned metal polish before... What polish would this be? Anything abrasive seems to strip off the Chrome finish. So what do the prof restorers do?
-
Brasso
If it is heavy rust on the curved grill fitted to an Erica I would fit a new grill. The ones Hohner sell now are stainless steel so will stay bright. The plating on the older ones is pretty thin and if there is more than light surface rust then some of the plating will be gone anyway. You can also clean everything off with abrasives, then spray paint in any colour you fancy.
-
Thx Theo.
-
as far as cleaning rusty reeds, I've been told that soaking them in petrol for a few hours works wonders!
I've used white spirit and meths to remove grease, old wax and general crud, but I'm not sure what effect they or petrol would have on rust.
Beware meths for too long! I left some reeds in meths by mistake (days, not hours) and it corroded the reed plates. Didn't affect function, but looked pretty awful, dark splodges.
-
as far as cleaning rusty reeds, I've been told that soaking them in petrol for a few hours works wonders!
I've used white spirit and meths to remove grease, old wax and general crud, but I'm not sure what effect they or petrol would have on rust.
Beware meths for too long! I left some reeds in meths by mistake (days, not hours) and it corroded the reed plates. Didn't affect function, but looked pretty awful, dark splodges.
Thanks for that info: I've never left reed plates soaking for more than about an hour - usually less - and never had any problems. As they come out of the spirit they get a going over with a softish brush and a clean cotton cloth and are then left in the sun (one of the advantages of living in the Med!) to dry for 20 minutes or so. No problems so far........
-
as far as cleaning rusty reeds, I've been told that soaking them in petrol for a few hours works wonders!
I've used white spirit and meths to remove grease, old wax and general crud, but I'm not sure what effect they or petrol would have on rust.
Beware meths for too long! I left some reeds in meths by mistake (days, not hours) and it corroded the reed plates. Didn't affect function, but looked pretty awful, dark splodges.
Thanks for that info: I've never left reed plates soaking for more than about an hour - usually less - and never had any problems. As they come out of the spirit they get a going over with a softish brush and a clean cotton cloth and are then left in the sun (one of the advantages of living in the Med!) to dry for 20 minutes or so. No problems so far........
Likewise - no problem with an hour or so.
Tom
-
Rust removal? try "Evapo-rust", It works great for me, even does reeds, just soak the metal in the stuff for an hour or two.
I tried it on a set of reeds after seeing it recommended on this Forum earlier. It worked very well for me too, but there was an unexpected side effect: it removed the 'blue' at the base of the reeds.
-
Intuitively I think you are better off removing rust and corrosion on reeds mechanically rather than chemically.