Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Rog on December 21, 2014, 12:47:20 PM

Title: Bass reeds for declubbed Hohner Modell II
Post by: Rog on December 21, 2014, 12:47:20 PM
Hi...looking for a bit of advice here.
I have declubbed the RH of a CF Modell II.
I want to convert the LH Bb/Eb bass/chord to a unisoric Bb.
I thought I'd be able to use the Bb reeds from an old Hohner student PA, but the big reeds are quite a bit smaller than the lovely old plates on the Modell II. The Modell II reed plate is 24.5mm x 70mm whereas the rather meagre looking plate from the PA is 19mm x 66mm.
So... my options are:
1) get hold of bigger reed plate
2) mod the reed block to accommodate the smaller reed plate
3) don't declub the RH

Does anyone have a bigger Bb bass reed plate and or what does the panel think...

Thanks
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: Nick Collis Bird on December 21, 2014, 12:56:26 PM
Harmonikas in Louni, Czech Republic will make anything for you Rog. Just send them a pattern. Theo was impressed with the quality.
PM sent.

Edited to add info.
They made my reeds for me in stainless steel because Hohner Organetts do not like spit thrown on them in any other material  >:(
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: Lars on December 21, 2014, 02:23:31 PM
I'm sure I can find some old hohner Bb/Bb for you if you're stuck for finding some locally.
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: Pete Dunk on December 21, 2014, 03:35:39 PM
I'll have a rummage through my box of old PA reeds at work tomorrow.
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: Rob2Hook on December 21, 2014, 03:51:12 PM
I'd hold off awhile until you manage to source an original reed pair.  The reeds on these old Clubs are lovely and I doubt any other replacement will match their tone.  That may not be critical, but in the interim you'll find that playing on the pull will sort most of the problems out and the results may usefully be transferred to other boxes - it tends to give a more legato style of playing.

Rob.
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: rees on December 21, 2014, 04:06:41 PM
I may be wrong but I think that the Eb basses are higher pitched than the Bb. If so you could apply some solder to the tips of the reeds to bring them down to Bb.
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: Steve_freereeder on December 21, 2014, 04:17:09 PM
I'd hold off awhile until you manage to source an original reed pair.  The reeds on these old Clubs are lovely and I doubt any other replacement will match their tone.  That may not be critical, but in the interim you'll find that playing on the pull will sort most of the problems out and the results may usefully be transferred to other boxes - it tends to give a more legato style of playing.

Rob.
I have found that Cagnoni 'macchina'-grade reeds from Charlie Marshall are an excellent match and are virtually indistinguishable in sound from the old Hohner reeds. I've used them in a couple of restoration projects and have been very satisfied with the results. It just goes to show that as much depends on the internal construction of the box and the materials used as the reeds themselves.

The Cagnoni reeds are not particularly expensive and Charlie Marshall will supply individual reed plates to your specification. For the relatively modest cost, it's worth trying them - they might well do the job to your satisfaction, or at least be an interim solution until you manage to source some original Hohner reeds.
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: Theo on December 21, 2014, 06:02:45 PM
I may be wrong but I think that the Eb basses are higher pitched than the Bb. If so you could apply some solder to the tips of the reeds to bring them down to Bb.

Just looked at one block Rees and it was the other way round, Eb lower.  But that can also be tuned up to Bb by removing the brass weight if there is one, or some enthusiastic filing.  The chord reeds are easier because you can just have to tune the Eb to D and the G to F#. Just a semitones down in each case, and as Rees says easy to do by loading the reed tip with solder.

BTW Steve, my experience of older Hohner bass reeds is that they sound much different from Cagnoni        but that might be as much to do with the smaller reed chamber you have to create, that to the reeds themselves. Scope for more investigation here.
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: tekyinblack on December 21, 2014, 06:08:32 PM
Hi Roger, I have a set of complete bass reed blocks from a 1935 club II you're welcome to if you want them. Don't suppose postage is much and I just keep moving them from place to place. Not sure when you'd get them at this time of year.
John 
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: Rog on December 21, 2014, 09:23:06 PM
Hi,

Just want to say a big thank you to everyone for their enthusiastic responses, among which are a couple of offers and some decent ideas. I'll send appropriate PMs and update on the resolution. What a great bunch of people you are.  Thanks again.
Title: Re: Bass reeds for declubbed Hohner Modell II
Post by: rees on December 21, 2014, 09:58:28 PM
I may be wrong but I think that the Eb basses are higher pitched than the Bb. If so you could apply some solder to the tips of the reeds to bring them down to Bb.

Just looked at one block Rees and it was the other way round, Eb lower. 

Memories are not what they used to be.
Use a soldering iron at full temp on the brass weight and it will slide off. If no brass weight, plenty plenty enthusiastic filing.  (:)
SimplePortal 2.3.5 © 2008-2012, SimplePortal