Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Shakin' All Hohner on March 27, 2015, 05:27:38 PM
-
Hi All.
A friend has given me his Hohner HA-113 to repair: the spring has broken under one of the bass spoons. The 'spoon' pivots on a spindle which is flattened like a rivet at each end. Before I file the end off the rivet to get at the spring - any ideas about replacing the spindle afterwards? How can I burr or flatten the end again to hold it in place? Maybe I should go for the clumsier fix of replacing the spindle with a wire which can be bent over at each end, or perhaps getting hold of a new mechanism from CGM - but that seems a bit over the top to replace a spring.
Many thanks, Alan
-
I use suitably sized panel pins, following on from Hohners predilection of using nails as hinge pins
-
I use suitably sized panel pins, following on from Hohners predilection of using nails as hinge pins
Excellent - many thanks Lester.
-
The hardest bit of the re-assembly is getting the two parts aligned, while holding the (compressed) spring in place and then inserting the new hinge pin. If the spring escapes it can inflict a nasty cut to fingertips.
-
...If the spring escapes it can inflict a nasty cut to fingertips.
Ouch! It sounds as though you speak from experience, Theo :o
-
I have hohnerable scars.
-
I have hohnerable scars.
;D
-
The people talk a loooot about the one row's here, that I am started to get interested. That model weltmeister, simply amazing. About the beauty but also the sound. Another Hohners one row also, I am starting to observe a lot. :D
-
I always replace the pin with a split-pin of the correct diameter. These springs often break so replacement is much easier with a split-pin.
I've seen Dan Eldon (son of Jim) replace one during a song with his band.
-
I always replace the pin with a split-pin of the correct diameter.
That's another great tip Rees and as you say, makes for easier replacement in the future. As for spring scars - I got plenty at Yeovil last year on Emmanuel's course :o
Thanks all.
-
Alan, on the Organette I used miniature nuts bolts and washers. A bit fiddly, but dead easy to replace a spring without filing bending or cutting.
I can vouch for a spring disappearing underneath a fingernail as well :o
-
I compress the spring between my fingers and insert the two legs into a metal tube (I.D around 5mm). I then position, holding the other end of the tube (length = 4cm), the spring inside the two base spoon pieces and line up all the holes to get the pin in. I use a small nut and bolt with washers and loctite.
I did it the way Theo did it and drew blood also.
Stephen
-
Well Stephen, you're responsible for my injuries, getting me into the Organette and not telling me about your method. ;D
-
That tube idea is a winner. Thank you. (:)
-
I've always use the tube method now.
-
I wish I had known. Imagine the trouble I had with those tiny nuts and bolts. I used a head wearing illuminated magnifier plus another small lens. The biggest problem was losing a spring. Pop! and it went right over your shoulder and never landed where you expected it.
I have the cleanest bookbindery workshop in the country ;D
-
I used a head wearing illuminated magnifier plus another small lens.
You have a choice of spare heads........??? Nick Kryten Bird........
Graham
-
;D ;D :D
-
I'm sure there are 100 springs of various sizes pinged around my workshop. I know they're there but they never ever reveal themselves.
I shall hire a very powerful electromagnet like the one on Breaking Bad. That should flush the little critturs!
-
Rees,
Years of finding small parts that have absconded in a workshop, sweep the floor very thoroughly you will nearly always find the escapee in the sweepings.
-
Sweep the floor! Sweep the floor!! That's women's work.
Oops, now I'm for it!
:-*
-
;D
-
Rees,
Years of finding small parts that have absconded in a workshop, sweep the floor very thoroughly you will nearly always find the escapee in the sweepings.
Would that be spring cleaning then?
-
Oh God. ::)