Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Vallenato831 on March 30, 2015, 03:23:24 PM
-
I have a Corona that the bellows seem pretty tight. Although their is a hissing air sound when closing the bellows without pressing any buttons. And if I close the bellows hard enough, sometimes 1 note will play on it's own. Which is the inner row, 5th or 6th button down. With this information anyone know where the leak is? Oh and I took off the grill and pressed on that notes valve to make sure it was seated against the pallet holes and closed the accordion. Still got a hissing sound. So I dont think it is caused by the pallet misaligned over the holes.
-
If a note is playing then it must be a leak at the pallet. There is no other way that a note will sound.
-
That makes sense but I dont get why when I press down on that pallet to ensure that it's firmly set I still get a hissing air sound.
-
Interesting this topic, about discover, realize it the air leaking is really happening! Cause I have one box, that I am distrusting about:
"Fuoock, I think it has an air leaking!"
And in the bellow I am always observing a small split there. But I have fears about touch on it, or try to confirm and maybe get the things worse, maybe OPENING a hole in a place where was just a split. But it is interesting. Cause I am always with this thinking about WHEN I will really discover if is there an air leaking or not really. ???
(Coincidently, this box is that I have the weaker volume sound, between my all).
So, I believe it is a real evidence about air leaking :o
-
It sounds like the leak isn't bad enough to affect normal playing, so maybe it isn't broke enough to need fixing? Unless there are other issues. maybe it can wait.
-
It sounds like the leak isn't bad enough to affect normal playing, so maybe it isn't broke enough to need fixing? Unless there are other issues. maybe it can wait.
Personally, I'd try to sort it. A little niggle that's barely noticeable but that YOU know is there can be very unsettling. You find you're constantly listening for it and your attention is never 100% on your playing. Don't ask how I know that.......
Graham
-
As aradru says, The air is being forced from the next 'weakest pallet'.
There may also be other leaks adding to the general hissing e.g. bellows gasket, but the note sounding will be a faulty seal at the pallet face.
-
I would suggest that the two symptoms are of different 'problems'. The hissing sound, as it seems to be quite audible, is probably the bellows gasket, or a missing screw/bellows pin, cracked soundboard, etc.
If the note sounding only happens if you press the bellows really hard it's because the air has to go somewhere and lifting a pallet is probably the route of least resistance, ie one spring being slightly weaker than the others. The note sounding almost certainly is not a problem in normal playing as the air will go through the pallets you have pressed and therefore not have enough pressure to lift the other pallet.
-
Bellows gasket could be ok if other pallets are lifting causing hiss but no note.
-
The sound is coming from the grill or keyboard. This I can tell surely. I will post a video once it's finished uploading. Also, did the leak test, I opened the bellows all the way and let it fall on its own whilge guiding it down. It took 25-30 seconds to close on all 3 times I did the test.
-
I would suggest that the two symptoms are of different 'problems'. The hissing sound, as it seems to be quite audible, is probably the bellows gasket, or a missing screw/bellows pin, cracked soundboard, etc.
If the note sounding only happens if you press the bellows really hard it's because the air has to go somewhere and lifting a pallet is probably the route of least resistance, ie one spring being slightly weaker than the others. The note sounding almost certainly is not a problem in normal playing as the air will go through the pallets you have pressed and therefore not have enough pressure to lift the other pallet.
I can replicate the note sounding maybe 1 in 10-15 tries. That note button does have a squeaky spring too. So I think the spring needs changing. The thing is I tried pressing on that notes pallet and closing the bellows and still get that hiss.
-
Ok does this sound like a good idea. I can take out the last reed block and tape the hole where that note sounded. And if I still get air, that means it must be something else.
-
(http://i946.photobucket.com/albums/ad305/SmoothSmoke/th_20150330_111319.mp4) (http://i946.photobucket.com/albums/ad305/SmoothSmoke/20150330_111319.mp4)
-
Found the leak!! >:(
I took out the keyboard and removed the 2 long screws that hold it to the body. I taped the 2 holes where those screws go through. Now no air leak at all!!! Now, how can I fix this? Is putting tape over the screws the only way to go?
-
I usually fit some leather washers under the metal washers. I have a bunch of scrap thickish soft leather which I punch them out from. Alternatively you can do what Hohner do now and cover the screw/washer in hot melt glue.
-
Thanks Lester, Reese and everyone else!!! Got this baby air tight now.
Unfortunately now I have sticking button!!! The button was that one button with the weakest spring/pallet. It's getting stuck underneath the keyboard. I kind of just bent it back into place as a temporary fix, but looks like I'll need to replace it's spring. That is something I will have to take into the shop. Not confident enough to take that task on myself
-
Unfortunately now I have sticking button!!! The button was that one button with the weakest spring/pallet. It's getting stuck underneath the keyboard. I kind of just bent it back into place as a temporary fix, but looks like I'll need to replace it's spring. That is something I will have to take into the shop. Not confident enough to take that task on myself
This is normal. The Hohner action is flimsy and can easily get misaligned. Bending it back into place is the correct remedy. The spring should be fine.
-
Unfortunately now I have sticking button!!! The button was that one button with the weakest spring/pallet. It's getting stuck underneath the keyboard. I kind of just bent it back into place as a temporary fix, but looks like I'll need to replace it's spring. That is something I will have to take into the shop. Not confident enough to take that task on myself
This is normal. The Hohner action is flimsy and can easily get misaligned. Bending it back into place is the correct remedy. The spring should be fine.
Good to know! If it misbehaves I'll just wrestle it back into place. And you're not kidding about flimsy. Sometimes I wish another big maker would make something to challenge the Corona III so Hohner can step up it's quality.
-
Try pushing down on a "good" button and then try pushing down on the one you think is bad, if the bad one is a lot easier to push then the spring is bad.
-
I will try that today Kimric! Thanks for the tip. Also, I'm not too far away from you, maybe 100 miles. If I need work done, I'll try with you.