Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Rog on April 16, 2015, 07:26:11 AM

Title: Glue for sticking things to celluloid finish
Post by: Rog on April 16, 2015, 07:26:11 AM
Hi
I need to reattach some trim to a celluloid finish. Any recommendations on glue for this? I was wondering about superglue but also concerned this might react with the celluloid. Or Bostick Solvent free which seems to be pretty strong. The trim is slightly sprung around a curve so the glue needs to be strong.
Title: Re: Glue for sticking things to celluloid finish
Post by: ACE on April 16, 2015, 09:18:59 AM
I have used a double sided bonding tape to fix a badge to a box. 3M do all sorts of industrial strengths. No room for error though, it takes some removing if you get it wrong. But at least you can clean of the residue with meths.
Title: Re: Glue for sticking things to celluloid finish
Post by: Kimric Smythe on April 18, 2015, 05:57:02 PM
super glue works fine if the item is not celluloid , it will not react with the celluloid in any manner.
If the trim is celluloid , or the metal trim with celluloid on the back , I use clear nail polish as a adhesive. You will want to use masking tape to hold the item in place for several hours, but the results are very good.
Title: Re: Glue for sticking things to celluloid finish
Post by: JNM SY on August 21, 2019, 08:15:48 PM
Hello Roger T,
                            I now have this same problem of detached trim needing to be reattached to celluloid. I was wandering what you eventually used & the result. The box I,m working on is a Club 3 BF and a previous owner glued on another corner trim with what looks like superglue which ran and left a mess. Thanks for any info.
                                                                                                                         John
Title: Re: Glue for sticking things to celluloid finish
Post by: Tone Dumb Greg on August 21, 2019, 11:31:33 PM
... I use clear nail polish as a adhesive. You will want to use masking tape to hold the item in place for several hours, but the results are very good.

My recollection is that acetone (active ingredient in nail polish) is a very good solvent for celluloid and will mark any it comes into contact with, so you have to be extremely carefully not to get it on any show surfaces.

Or, am I thinking of perspex?
Title: Re: Glue for sticking things to celluloid finish
Post by: JNM SY on August 22, 2019, 06:13:54 AM
Acetone definately will melt celluloid. Double sided tape would be strong enough but would lift the trim above the surface. Pva might work and its easy to clean off any excess -but I,m not sure how well it bonds with metal.  I think the trim was originaly held on with some kind of hot melt glue.  I,ll do a couple of trials on an old scrap box first just to be safe...
Title: Re: Glue for sticking things to celluloid finish
Post by: Theo on August 22, 2019, 08:35:33 AM
The traditional glue for celluloid is celluloid scraps dissolved in acetone.  Nail varnish is pretty much the same so just follow the advice in a previous post from Kimric Smythe.
Title: Re: Glue for sticking things to celluloid finish
Post by: JNM SY on August 22, 2019, 05:05:51 PM
Och but all my nail varnish has glitter in it!   After experimenting It turns out  -   the experts were right!
  I never doubted them for a minute.   (Ok I did).   So, the hot glue gun - no good - the glue went cold instantly .
   Next -  superglue  - refused to stick at all! + messy,dont even bother.  PVA glue which I thought would be the easiest was  messy and doesnt grab straight away so slides about when trying to clamp in position. Not sure about the strength of the bond either.

  So lastly I mixed a inch square bit of celluloid with about 5ml of  100% acetone in a foil empty cat food tray and stirred for about 5 mins until it dissolved into a soft toffee-like mush.I was worried about how to apply this stuff but it turned out to be the easiest method of all.  Applied with a cocktail stick & plonked into position - it stays!   Piece of cake!   ( I had the nibbles after all the fumes - note to self - next time open a window)  The mixture is also very good/easy for attaching the odd bit of celluloid that needs replacing.   I'm going for a lie down now, I have a headache...
Title: Re: Glue for sticking things to celluloid finish
Post by: JNM SY on August 23, 2019, 06:28:05 PM
Update:-  After leaving them clamped for 24 hours, the strongest bond was  PVA glue!
 The one with the acetone / celluloid mixture came off with a very slight tug!
   So, for me anyway  -   pva, or more acurately -  Evo Stick wood Adhesive  -  every time.     
                                                                                                                                                           John
SimplePortal 2.3.5 © 2008-2012, SimplePortal