Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Tone Dumb Greg on May 23, 2015, 01:50:45 PM
-
I have a liitle problem that I would normally take it to Roger at Kingsbridge, the very skilled gentleman who fettles my instrument, b :out I cannot get it to him until after the summer season is finished and it is starting to annoy a bit. I suspect it is something simple.
I have two things happening with my (chinese pokerwork), which is coming up for its third birthday:
1. One reed of a pair stops sounding. This has happened to the f on the G row and the ^c and e on the D row.
2. A note stops sounding completely for a period and then starts working again. Seems to happen with the less well used notes, in particular those on the squeaky end. Up 'till now I have coped by picking up the note on the alternate row.
I took the covers and bellows off the treble end, to see if there was an obvious cause, for problem 1, (problem 2 having gone away for the time being), but could not identify one. I was looking for "foriegn matter", but found none. I am open to advice (it might be worth mentioning that I have an engineering background and I am usually pretty good at reassembling what I have rent asunder).
Greg
-
The most likely thing is foreign matter stuck in the clearance gap between the reed tongue and the reed plate. This can be something very tiny that you would only see with a magnifying lens. The cure is to simply lift the tip of the reed and let it ping back into place. Easy to do for the push reeds, which are on the outside surface. For the pull reeds you can either go under the valve and push down on the reed tip, or go in through the vent under the reed block and depress the reed tip. Both operations are easier with the reed block taken out of the box. Steel reed tongues are fairly tough but be careful to avoid any permanent bending.
-
Theo- Should I try the same thing on my Loffet GC? I have a high A on the C row that is slow to start, but it does play.
Problem is I need to hit this note first before I can apply harmony, it is getting annoying
-
Slow starting not is likely to have a different cause, usually a reed set too high or possibly a faulty valve
-
I hate to ask this, but where is the reed in the blocks when I attempt disassembly.
Otherwise I'm sure I can find from this forum somewhere
Sorry to be a pest.
-
Thanks Theo. The notes I have the problem with are all on the pull. Guess I have to go a bit deeper to access those reeds. Time to start poking the pokerwork again!
-
Hmm! Removed bellows and reed blocks and gently nudged guilty reeds. Reassembled and notes sounded fine (:) Started playing and discovered Bb had developed a very high pitched whistle, rather than a clear note. Repeated the exercise without any improvemnt :(
Get back to it later.
-
I hate to ask this, but where is the reed in the blocks when I attempt disassembly.
Otherwise I'm sure I can find from this forum somewhere
Sorry to be a pest.
Open the box and you will see the reed plates in rows along either side of the reed blocks. The reed tongues are steel and have a rivet at one end.
-
Thanks Theo
I located and slid a business card under it. After reassembly it plays fine.
-
Its not occurred to me before, but how does one 'ping' an inside / push reed. Has anyone devised a special pinging tool for inside reeds? Maybe a thin rod with a tiny hook on the end.
-
Its not occurred to me before, but how does one 'ping' an inside / push reed. Has anyone devised a special pinging tool for inside reeds? Maybe a thin rod with a tiny hook on the end.
No need to attempt to 'ping' the reed. Use a cocktail stick: carefully lift the valve a small amount with the point of the stick, then push the stick through the slot to gently ease the underneath reed tongue up and down a few times. This is usually enough to clear any debris which may be obstructing the reed tongue. Repeat as necessary. A persistent blockage may need a few puffs of air, e.g. from a camera lens cleaning tool (the sort with a nozzle and rubber bulb). It's best not to blow air from your mouth as this is warm and moist and may induce rust to form prematurely.