Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: mselic on June 18, 2015, 02:45:20 PM

Title: squeeky Hohner Erica bass button
Post by: mselic on June 18, 2015, 02:45:20 PM
I have a lovely new Hohner Erica, but I've noticed that a squeek has developed on one of the bass buttons.  It's not always immediately present, but tends to show up quickly after a bit of playing.  Although the instrument is new, I've played in many, many hours and this is a recent development.  I will be opening the bass side up later today (never done it on this accordion) to see if I can figure out what it might be.  I browsed through a thread on a similar topic, and the general consensus there was to NOT use any kind of lubricant on the spring.  I have to admit, when I heard a squeek develop my first thought was that something needed lubricating.  Should I not use any kind of lubricant, then?  What else should i look for when I open up the bass side?  Anything I need to be aware of or be careful of in my troubleshooting? Thanks.
Title: Re: squeeky Hohner Erica bass button
Post by: Theo on June 18, 2015, 02:50:56 PM
Sometimes the buttons rub against the woodwork and squeak.  Pencil lead rubbed onto the wood inside the hole will fix that, though you may find it difficult to get the pencil in there.

Don't assume its the springs, they are just one possible source.  Any of the moving parts can rub and squeak.  First identify the source.   Powdered graphite mixed with meths works well and does not attract dust.
Title: Re: squeeky Hohner Erica bass button
Post by: mselic on June 18, 2015, 03:02:44 PM
Thanks, Theo.  I will be looking into it later today.  You mentioned powdered graphite mixed with meths...forgive my ignorance, but what are meths?
Title: Re: squeeky Hohner Erica bass button
Post by: Theo on June 18, 2015, 03:06:44 PM
Denatured alcohol.  in UK known as methylated spirits.  Any kind of (pure) alcohol will do.
Title: Re: squeeky Hohner Erica bass button
Post by: mselic on June 26, 2015, 03:40:53 PM
I opened up the bass end and it seems that moving the positioning of the spring on the rod makes a difference.  I re-positioned the spring to a spot along the rod where the squeeking stopped.  I've closed it back up and will see if that's done it or if the squeek will come back with playing...
Title: Re: squeeky Hohner Erica bass button
Post by: mselic on June 26, 2015, 10:38:12 PM
Unfortunately, the squeek is back...moving the position of the spring seemed to make a difference, but did not fix the problem.  I'm not sure what is needed...there are only so many moving parts, and I can't quite understand where the noise is coming from...
Title: Re: squeeky Hohner Erica bass button
Post by: mselic on June 26, 2015, 10:40:29 PM
Also, I'm not sure why I've been spelling "squeak" like "squeek".... ::)  I can spell, honest...
Title: Re: squeeky Hohner Erica bass button
Post by: malcolmbebb on June 26, 2015, 10:42:54 PM
I have squeaky springs on my Erica - moving the spring seems to cure the problem temporarily, as you found. Not such a problem when I can give it some welly, but most distracting when trying to play quietly.
Title: Re: squeeky Hohner Erica bass button
Post by: mselic on June 26, 2015, 10:56:54 PM
Source of problem discovered! It wasn't the springs or any of those components. Rather, it was as Theo mentioned was possible - when upright, the button itself would rub against the woodwork.  I had looked into that initially but didn't determine it to be the source of the problem at the time.  Now it's certain! Whenever I had the box on it's side, the button wouldn't squeak, but when up right, the button would hang down ever so slightly and rub up against the woodwork of its opening.  Now to try and fix it...Theo mentioned getting pencil lead in there somehow...
SimplePortal 2.3.5 © 2008-2012, SimplePortal