Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Johnniez on July 08, 2015, 12:08:49 AM

Title: Hohner HA-114 BASS push reed ?
Post by: Johnniez on July 08, 2015, 12:08:49 AM
Hi all

Anyone know which reed is being used on the HA-114 for the BASS Push sound..
To me its lagging/choking/lazy only on the Push Pull is fine... Wonder if I can looked at it as I take the top off or would I have to remove the reed?

And when I do look at it.. What do I look for and/or do to remedy this? It's getting annoying.. I have same box in D and its fine..

help! Never touched an accordion reed. Lots of bagpipe reeds tho. thats fun too... ;-)

Tnx
Johnnie
Title: Re: Hohner HA-114 BASS push reed ?
Post by: squeezy on July 08, 2015, 10:23:57 AM
You don't necessarily need to remove the reed.  What you have to do is carefully remove the 4 pins that connect the bass side of the instrument to the bellows (keep them somewhere safe!) and have a look at the reeds which will be mounted flat to the inside of the bass end.  There will be 2 areas of reeds - the ones together with the largest reed will be the bass ones (they all play together to give the bass note) - and luckily for you the ones facing in to the bellows are the ones for the push note.

Have a visual inspection for any debris that could be clogging up one of the reeds and make sure the reeds are not loose in their housing (they are usually waxed in) ... then you will need to check that the valves that sit next to the reeds are flat to the reed plates and covering the gap efficiently.  If the ones facing you are OK - it may be that the ones on the reverse side of the reed plate are not working properly - and that's harder to look at without removing the reeds - but you can investigate by carefully pulling back the reeds that are facing you to get to the valves which are underneath.

Good luck.
Title: Re: Hohner HA-114 BASS push reed ?
Post by: Malcolm Clapp on July 08, 2015, 10:34:29 AM
What Squeezy said.

However, if that all seems OK and no improvement, it is likely that the height of the tip of one of the push reeds (the ones you can see are the push reeds!) needs adjusting, but whether it will need lowering or raising is impossible to say without seeing/playing it, as, to my mind, choking and lazy are opposing descriptions. Too low and it will "choke" if you squeeze too hard; too high and it will need a very strong pressure, which I would describe as "lazy".

A little judicious bending may be in order....possibly best left to a repairer, but inexpensive and probably a 2 minute job including tea break!
Title: Re: Hohner HA-114 BASS push reed ?
Post by: Johnniez on July 08, 2015, 10:49:40 AM
Hi all and thanks

Well I see the difference now in choking or lazy... SO I get that choking means that it will play then quit  or just quit.. And lazy would be taking a bit longer than normal to get going..

Mine is taking a bit to get going .. Not a right now response as the Pull or the Push Pull on the chord side..

So I would think the mode of operendi would be any more that I make to put it back together and try. If its better then great. If not or worse. I undo what ever I did ..

is that close to right way of doing things.

Johnnie

tnx again
Title: Re: Hohner HA-114 BASS push reed ?
Post by: Malcolm Clapp on July 08, 2015, 12:48:52 PM

... SO I get that choking means that it will play then quit  or just quit.. And lazy would be taking a bit longer than normal to get going..

Mine is taking a bit to get going .. Not a right now response as the Pull or the Push Pull on the chord side..


Almost! It's all about the pressure it takes to get the reed moving. A reed set too low may respond well at low pressure, but will choke at a higher pressure. A reed set too high (what I call lazy) will not respond until a greater pressure is applied. So it is a compromise based on how strongly you push the bellows, the airtightness of the instrument and the condition of the reed(s) at fault. There are no magic measurements afaik, but once you've set a few thousand reeds, you get a feel of what is about the right height above the reed plate (most of the time!!!)
Title: Re: Hohner HA-114 BASS push reed ?
Post by: Johnniez on July 09, 2015, 11:20:16 AM
Tnx Malcolm

Well I check it out and to be honest I really don't want to mess with it..

I have the same box in the key of D. and it also seems to be doing similar to the C box..

Maybe its me, or just suppose to be that way.. Both box are fairly new so maybe the reeds need to be broke in.. I am just learning pretty much. On book 1 lesson 24.. lol..

So at the end of day I can just live with it. I just mess around in my living room sittin in my lazyboy and play along to different Cajun tunes and also Scottish.. I have Cock of the North down pretty good.. .lol..

thanks for all the help..

Johnnie
Title: Re: Hohner HA-114 BASS push reed ?
Post by: Johnniez on July 11, 2015, 10:36:01 AM
Well I changed my mind when a buddy came over that knows about these boxes..

I wanted to put in small magnets for the stops also

Well I did the magnets and he walked in the door just as putting the last magnet in. He never saw that before.. Heard about it.. Anyway showed him what was going on the he did the last one.  I used .114 dia magnets 1/4 long.. Drill the holes, put in the stops, slid the magnets in the hole, pushed them down up against the stop rod, then a dap of wood glue in the hole. Not going anywhere. ;-)

Trevor had a look at the bass side, easy to get at ... All he did was flick the two reeds on the bass side a few times, then put he box together and tried it.. Apart once more, same thing done, put back together and now its great. Bass and chord have same response and volume or close enough.. 

Thank again everyone for the help..  :|glug :|glug :|glug

Johnnie
SimplePortal 2.3.5 © 2008-2012, SimplePortal