Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Mike-T on July 24, 2015, 06:29:24 PM

Title: Removing celluloid from a box.
Post by: Mike-T on July 24, 2015, 06:29:24 PM
Hi folks, I've acquired a double ray that at some time or other has been used for balancing cigarettes on, causing damage to the celluloid, I have it in mind to strip it off and polish it up to a decent wood finish. The question is,  is there an easy way to remove said celluloid? 
 Mike.
Title: Re: Removing celluloid from a box.
Post by: Theo on July 24, 2015, 06:45:52 PM
Just get a knife under an edge and lift it and it will peel off.
Title: Re: Removing celluloid from a box.
Post by: Mike-T on July 24, 2015, 06:55:36 PM
Ok Thanks Theo.
Title: Re: Removing celluloid from a box.
Post by: Lester on July 24, 2015, 07:02:54 PM
Just done it to an Erica for the very same reason. As Theo said pick away at edge and the celluloid will start to peel. You need to be careful getting the knife ( or similar) under the celluloid as the wood underneath is just fairly soft ply,

I then sand it off with palm sander til the surface is OK then finish with Liberon Finishing Oil (http://www.axminster.co.uk/liberon-finishing-oil) and then wax.

The main problem you will come up against (if you are me anyway) is that the bellows gasket will need renewing with some thicker stuff as there is a layer of celluloid that will be removed on the mating face between the casework and the bellows.
Title: Re: Removing celluloid from a box.
Post by: Lester on July 25, 2015, 06:07:12 PM
Three examples

(https://scontent-lhr3-1.xx.fbcdn.net/hphotos-xta1/t31.0-8/s2048x2048/11782316_863649163691056_6946329464255874795_o.jpg)

Left to right, Liberon Finishing Oil & wax, Liberon Finishing Oil & wax, wood strain and spray lacquer.
Title: Re: Removing celluloid from a box.
Post by: TomB on July 25, 2015, 08:26:20 PM
Often wondered if stripping off the celluloid has any effect on the sound of the box, presumably it makes it just a shade lighter in weight?
Title: Re: Removing celluloid from a box.
Post by: Mike-T on July 25, 2015, 08:40:08 PM
Lovely job Lester, gives me a high benchmark to aim for! Would you advise for or against polishing inside while I have the thing in bits?
Mike.
Title: Re: Removing celluloid from a box.
Post by: Lester on July 25, 2015, 08:44:51 PM
Lovely job Lester, gives me a high benchmark to aim for! Would you advise for or against polishing inside while I have the thing in bits?
Mike.

I personally would not bother as I can think of no reason to do it. The only boxes that I have worked on that have been varnished in side have been very low end and horrid.
Title: Re: Removing celluloid from a box.
Post by: Andy Next Tune on May 09, 2016, 04:31:18 PM
I am contemplating taking this route to revitalise a tatty red Erica which has clearly enjoyed a good life!

Lots of very helpful advice from Lester and Theo below.

Has anyone taken any alternative approaches to finishing the box after the celluloid has been removed?

Any other pics of Ericas 'sans celluloid' would be appreciated.

Title: Re: Removing celluloid from a box.
Post by: Lester on May 09, 2016, 04:48:43 PM
I've sprayed on using Halford's Car Primer followed by Car Enamel and a few coats of Car Lacquer
Title: Re: Removing celluloid from a box.
Post by: Andy Next Tune on May 10, 2016, 10:01:01 PM
Erica's red celluloid is no more  8)

......which leaves a thin black strip of celluloid inset in the woodwork on the back the the treble and bass carcasses where the ends of the celluloid sheet met.

Have previous celluloid strippers removed this as well (and somehow filled the trench!) or left them as a feature?
I'm tempted to leave them, although they do sit slightly proud of the surface of the wood.
Title: Re: Removing celluloid from a box.
Post by: Lester on May 10, 2016, 10:21:15 PM
Erica's red celluloid is no more  8)

......which leaves a thin black strip of celluloid inset in the woodwork on the back the the treble and bass carcasses where the ends of the celluloid sheet met.

Have previous celluloid strippers removed this as well (and somehow filled the trench!) or left them as a feature?
I'm tempted to leave them, although they do sit slightly proud of the surface of the wood.

I left them in place and just sanded them flush when refinishing the woodwork.
Title: Re: Removing celluloid from a box.
Post by: Grape Ape on May 10, 2016, 11:20:32 PM
Has anyone ever tried this on a box like the III BS where the keyboard is also covered? What about the switches on the back of the keyboard? Will they present a problem?  Can they be safely removed?
SimplePortal 2.3.5 © 2008-2012, SimplePortal