Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: KLR on July 26, 2015, 06:16:58 PM

Title: Reed damper
Post by: KLR on July 26, 2015, 06:16:58 PM
I bought an old Swiss made CBA the other day, C griff, "Record" brand by Ackerman Weld of Zurich, "Fabrik F. Hoeffleur Zurich-Seebach".  Here's another example, built by Paolo Soprani apparently:  Nice and rare RECORD button accordion / accordian! "C" system! | pianos, keyboards | City of Toronto | Kijiji (http://www.kijiji.ca/v-piano-keyboard/city-of-toronto/nice-and-rare-record-button-accordion-accordian-c-system/1086630722)  About all mine has in common with that one is the logo, though.  This one was designed by H. Ackerman, according to the seller.

The bass section of mine really caught my eye, with the damper for the bass reeds; it looks like someone worked on pianos.  Never seen the like before, was this commonly done?  This is a nice box, pinned reeds, with leathers that have been slashed crosswise - kind of like Swiss landsknecht fashions, come to think of it, which were slashed decoratively.  The treble keys unfortunately are made of some crummy plastic that falls apart, forming sinkholes in the middle before disintegrating entirely, so I'm turning out replacements from boxwood.
Title: Re: Reed damper
Post by: Steve_freereeder on July 27, 2015, 12:13:33 AM
Interesting...
Is the purpose of the dampers to cut out the bass reeds altogether, a bit like some melodeons have a stop to remove the low fundamental reed from the basses? Or is it to stop the sometimes annoying 'twangy' vibration of the large reeds continuing after the button has been released?
Title: Re: Reed damper
Post by: KLR on July 27, 2015, 07:40:01 AM
It kills the bass and one set of middle reeds entirely, just like coupler mechanisms usually do.  Doesn't seem to have a halfway point you can actuate.
Title: Re: Reed damper
Post by: Steve_freereeder on July 27, 2015, 08:28:09 AM
It kills the bass and one set of middle reeds entirely, just like coupler mechanisms usually do.  Doesn't seem to have a halfway point you can actuate.
OK - thanks.  (:)
Title: Re: Reed damper
Post by: blue eyed sailor on July 27, 2015, 08:40:12 AM
It kills the bass and one set of middle reeds entirely, just like coupler mechanisms usually do.  Doesn't seem to have a halfway point you can actuate.

Wouldn't this solution have to be considered as quite favourable as the one reed left will receive the full amount of air then, not restricted by a shut windway?

Best wishes - Wolf
Title: Re: Reed damper
Post by: Steve_freereeder on July 27, 2015, 09:01:38 AM
Wouldn't this solution have to be considered as quite favourable as the one reed left will receive the full amount of air then, not restricted by a shut windway?

I don't really understand this, sorry.
In a conventional stop/switch mechanism, the slider cuts off the supply of air to the reeds to be silenced, but the remaining reed(s) will still receive a 'full amount of air'.
Title: Re: Reed damper
Post by: george garside on July 27, 2015, 09:26:06 AM
Is it a more complicated or a less complicated way of doing what the common sliders do?.  The only aadvantage I can see is that it reduces the potential for air leakage  and maybe gives a faster change than a slider??




george
Title: Re: Reed damper
Post by: Lester on July 27, 2015, 09:30:53 AM
Is it a more complicated or a less complicated way of doing what the common sliders do?.  The only aadvantage I can see is that it reduces the potential for air leakage  and maybe gives a faster change than a slider??




george

It almost certainly does not reduce the potential for air leakage. It will work well for the closing the valves on the outside of the block (for the suck reeds) but for the reeds with the valves on the inside (Push notes) it will prevent the reeds sounding but air will leak around reed and through the open valve.
Title: Re: Reed damper
Post by: blue eyed sailor on July 27, 2015, 09:43:30 AM
Wouldn't this solution have to be considered as quite favourable as the one reed left will receive the full amount of air then, not restricted by a shut windway?

I don't really understand this, sorry.
In a conventional stop/switch mechanism, the slider cuts off the supply of air to the reeds to be silenced, but the remaining reed(s) will still receive a 'full amount of air'.

My point (right or wrong) was that (at least in smaller boxes) the more voices you have the smaller the aperture for the wind supply will have to get. With these dampers you can keep resp. apply the wide cross-section of a one- or two-voice...
Title: Re: Reed damper
Post by: KLR on July 27, 2015, 05:06:26 PM
That's a good point, Lester.  I dunno if I'm losing out on air much with the reeds dampened, like most all old boxes it could really stand revalving in the first place to work at its best.  It isn't bad though, good enough for practice's sake. 

I wonder about the pinned reeds, too.  It's nice to not have all that messy wax but wax certainly fills in any and all paths for air to escape.  And those pins are a pain to remove and replace, too.  And the felt underneath the reeds probably needs replacing just like bellows gaskets.
Title: Re: Reed damper
Post by: Etienne on July 28, 2015, 11:41:17 AM
It's something in use for the registers of reed organs (can't find a good picture to illustrate...).
SimplePortal 2.3.5 © 2008-2012, SimplePortal