Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: robotmay on January 07, 2016, 09:42:06 PM

Title: Spinning button
Post by: robotmay on January 07, 2016, 09:42:06 PM
The G/A button on my Lilium has decided to get a bit more lively. I'm assuming the threading in the plastic has gone; what's the best way to fix this? I have a variety of glues, but I assume it would be better to have a less-permanent fix as it's easier to remove the button from the plastic than the plastic from the metal rod? I have a small unopened bottle of liquid hide glue; would that be a reasonable choice?

(http://i.imgur.com/W66WqEN.gif)
Title: Re: Spinning button
Post by: Theo on January 07, 2016, 10:03:18 PM
If the button is spinning then you really need a new button.  Easily available from Charlie Marshall.
Hide glue is only effective on porous materials, not metal or plastic.
Title: Re: Spinning button
Post by: robotmay on January 08, 2016, 12:04:01 AM
Ah I see, so it's spinning around the metal itself, rather than the metal spinning inside the plastic attached to the lever. I'll have a look to see if Charlie has any matching ones in stock!
Title: Re: Spinning button
Post by: robotmay on January 09, 2016, 05:11:01 PM
After some very speedy posting from Charlie, I now have a few spare buttons!
I do have another quick question: how do I go about removing the old one if I can't rotate it to extract it? Do I have to break it off in order to get some pliers around the screw shaft, or is there a better way?
Title: Re: Spinning button
Post by: rees on January 09, 2016, 05:22:55 PM
Sorry to say it but I think that is the only way. Careful now.
Title: Re: Spinning button
Post by: Theo on January 09, 2016, 05:37:31 PM
Put some masking tape over the button before breaking it off.   That will help to contain sharp fragments.
Title: Re: Spinning button
Post by: robotmay on January 09, 2016, 05:40:40 PM
Great, thanks guys. I'll give that a go tomorrow!
Title: Re: Spinning button
Post by: george garside on January 09, 2016, 07:23:03 PM
spinning button ? good name for a tune!

george ;)
Title: Re: Spinning button
Post by: Psuggmog Volbenz on January 11, 2016, 10:01:10 AM

Hide glue is only effective on porous materials, not metal or plastic.
Sorry Theo, this is inaccurate. Hide glue will stick to non porous materials if correctly applied. It is sometimes applied to glass to create decorative chipping. When applied hot to prepped glass, the glue adheres so well, that as it contracts while cooling, can cause a piece of glass to flake off attached to glue. I would not use hide glue for adhering metal or plastic, but often use it for gluing shell and bone inlay on vintage musical instruments, as was done when they were originally constructed.  "superglue" is usually used by contemporary luthiers for this purpose.
Title: Re: Spinning button
Post by: Theo on January 11, 2016, 10:10:07 AM
Thank you for the correction.  That's interesting.
Title: Re: Spinning button
Post by: robotmay on January 12, 2016, 11:39:48 AM
Done, thanks for the advice guys. In the end I used my rotary tool to drill the plastic in a line through the middle, which allowed me to crush the metal disc in and grip the whole lot in some pliers and twist it out. First time I've put a button on without one of those tools Emmanuel had. I think I've got it aligned properly but the fresher felt is like an optical illusion when trying to judge position ;D

(http://i.imgur.com/DCpnY2q.jpg)
(http://i.imgur.com/qJ2E5Kx.jpg)
Title: Re: Spinning button
Post by: Broadland Boy on January 13, 2016, 12:25:04 AM
Nice careful bit of controlled demolition  :D
Title: Re: Spinning button
Post by: Psuggmog Volbenz on January 13, 2016, 04:22:38 AM
...First time I've put a button on without one of those tools Emmanuel had....

(http://i.imgur.com/DCpnY2q.jpg)
(http://i.imgur.com/qJ2E5Kx.jpg)
Could you please describe or show a photo, of the tools Emmanuel had, I will probably never get to see them personally.
Title: Re: Spinning button
Post by: Rog on January 13, 2016, 07:49:19 AM
If it's the one I'm thinking of, it is basically a collet that grips the button and allows you to screw it onto the lever.
Title: Re: Spinning button
Post by: Theo on January 13, 2016, 08:49:21 AM
Fingers are just fine for removing and replacing the occasional button.
Title: Re: Spinning button
Post by: robotmay on January 13, 2016, 09:46:10 AM
Yep, the finger-attached one seems to be holding up fine so far. It had a nice bedding-in with some vigorous morris tunes last night.

Here's what the button tool looks like for anyone interested:

(http://i.imgur.com/fTSnQh8.jpg)

I found it quite useful when doing a lot of buttons, though Emmanuel had two of them and one gripped slightly better than the other, so I imagine they can be quite variable.
Title: Re: Spinning button
Post by: Psuggmog Volbenz on January 14, 2016, 02:28:52 AM
Thanks for the photo, this gives me the information i would need to machine a set.
Title: Re: Spinning button
Post by: boxcall on January 14, 2016, 03:11:14 AM

Hide glue is only effective on porous materials, not metal or plastic.
Sorry Theo, this is inaccurate. Hide glue will stick to non porous materials if correctly applied. It is sometimes applied to glass to create decorative chipping. When applied hot to prepped glass, the glue adheres so well, that as it contracts while cooling, can cause a piece of glass to flake off attached to glue. I would not use hide glue for adhering metal or plastic, but often use it for gluing shell and bone inlay on vintage musical instruments, as was done when they were originally constructed.  "superglue" is usually used by contemporary luthiers for this purpose.
Glass is poruos under a microscope and if prepped with acidic cleaner it's even more so, I would think bone and shell would be also.
This would explain why hide glue sticks to it so well.
SimplePortal 2.3.5 © 2008-2012, SimplePortal