Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: mr hohner on June 25, 2016, 06:45:18 PM

Title: Attaching plastic valves
Post by: mr hohner on June 25, 2016, 06:45:18 PM
Hi all,
I'm about to start sorting out the reeds in one of my old boxes. I am getting some valves and was wondering what type of glue I should use to attach them to reeds with. If anyone could enlighten me I would be very grateful.
Cheers
Mr hohner
Title: Re: Attaching plastic valves
Post by: Lester on June 25, 2016, 06:47:29 PM
I use EvoStik Impact

(http://www.wilko.com/content/ebiz/wilkinsonplus/invt/0150127/0150127_l.jpg)
Title: Re: Attaching plastic valves
Post by: mr hohner on June 25, 2016, 07:32:39 PM
I use EvoStik Impact

(http://www.wilko.com/content/ebiz/wilkinsonplus/invt/0150127/0150127_l.jpg)

Thanks Lester, I'll try using that.
 :||:
Title: Re: Attaching plastic valves
Post by: Lester on June 25, 2016, 08:14:45 PM
I clamp the tube in my bench vice, give it a little squeeze to get a blob of glue on the tip, wipe the valve across the blob, stick it on the plate.

(https://lh3.googleusercontent.com/Wl8nreImg5wI3tIcOSGxMt5uORplWyJImz1OZoOnRH5JQurRieTo4T3JeoUs_pzTgpvoXS7pIO42HJO773qyrGFf-EFo9aB0czDru3VWHqGhrVt65OyhrKWEa117JJgdV47hl6j1De1X7-Sr4C6uA0alwwHLpDcn8bKuGbVsT0vN93_O_TfXdUIJb8QiEU5uMzPNtGsvJ-S_2jN4w9WSuxmGimYGuHvFntH7tinvOuKbXWGJNtjWSXHUPBMQS5PzbTo9917MBtaMI0RoofijaIle-kUda-UjM-2kYgyB0yVGszbjCuCOrHu2lUmt82LdrRuBV7QvVsfn6KOH1uqak-Vbajk-aUIKfv-Nv7HC6L2ZSIGaEAM50P-z-093Rz2TogK6-MOCzrxrr2oHBqTrg-k8sc6DNWJlCfUHytNT5b0irHQE6HMRtsx66vAW0JC__1GdXdW5-U2-iHNoZD9qTKpLi4kcFCEYMSOqxsi5rpCmyQiohlkxQXnnL9A56r59MC6koXxDdELiHsfGsjWg9fCxb3Uw5ZF4OGoQ014eGQLfeBGgCb5ScUSNvsSZl5e_9ehmULahlfOBXM1s9uJeeAQE8j8Pqjmw=w600-h800-no)
Title: Re: Attaching plastic valves
Post by: Ebor_fiddler on June 30, 2016, 11:42:44 PM
Yes, as little as you can get away with.
Title: Re: Attaching plastic valves
Post by: Steve_freereeder on July 03, 2016, 06:32:03 PM
Hi all,
I'm about to start sorting out the reeds in one of my old boxes. I am getting some valves and was wondering what type of glue I should use to attach them to reeds with. If anyone could enlighten me I would be very grateful.
Cheers
Mr hohner
We covered this in the melodeon maintenance day which Rees and I held in Mendlesham back at the end of March. You were there - did you nod off at that stage?  ;)
Title: Re: Attaching plastic valves
Post by: Rog on July 03, 2016, 09:55:20 PM
An alternative to Impact is UHU, smeared in blobs on a sheet of card. You'll get a few valves out of each blob before it dries.  UHU sets hard so it's a bit closer in property than Impact to the brown shellac you often find on old valves. I think it sets faster than Impact as well, so for me is easier to use, but that is just my opinion. They both give off fumes and impact is particularly horrible after a while. I have also used Bostik solvent free, which has a longer setting time, but it doesn't set hard (neither does Impact) and is difficult to clean off, as is Impact.
Title: Re: Attaching plastic valves
Post by: mr hohner on July 04, 2016, 09:15:37 AM
Hi all,
I'm about to start sorting out the reeds in one of my old boxes. I am getting some valves and was wondering what type of glue I should use to attach them to reeds with. If anyone could enlighten me I would be very grateful.
Cheers
Mr hohner
We covered this in the melodeon maintenance day which Rees and I held in Mendlesham back at the end of March. You were there - did you nod off at that stage?  ;)

I lost the notes I made at the event... That my excuse...   ;)
Title: Re: Attaching plastic valves
Post by: Lars on July 04, 2016, 09:42:46 AM
An alternative to Impact is UHU ...  UHU sets hard ...

... which is why I would actually think you should avoid it. It dries hard, and is more prone to getting brittle when used on aluminium and plastic. The wonders of Impact or Bostik Contact #5 is, that it never dries hard, and will stand flexing for years and years.

My personal favorite method is to squeeze out a drop off the tip of the tube, take the drop with a cottonbud/Q-tip, and use that to apply it to the valves. It's faster than it sounds like, and will allow spreading in a thin, even layer, and control how far up the valve you want the glued surface to be.
Title: Re: Attaching plastic valves
Post by: Graham Spencer on July 04, 2016, 09:43:44 AM
I use Bison Kit Universal; it's a contact rather than an impact adhesive, slightly easier (IMHO) to work with than Evo-Stik, and much easier to clean off if when you have to.

Graham

(Incidentally I use pretty much the same technique as Lars, except that I use a cocktail stick rather than a cotton bud)
Title: Re: Attaching plastic valves
Post by: Lars on July 04, 2016, 01:21:19 PM
I except that I use a cocktail stick rather than a cotton bud)

I tried that, but I found that a cotton bud was better at holding on to excess glue - a plain stick just moved the blob around, whereas the cotton bud would 'dispense' glue in a more even layer. Maybe I'm just too used to the feel of the cotton buds? As with most things in the world of reedwork, doing things 2000 times makes the fingers to for the 'feeling' more than anythings else.
Title: Re: Attaching plastic valves
Post by: rees on July 04, 2016, 03:55:37 PM
I except that I use a cocktail stick rather than a cotton bud)

As with most things in the world of reedwork, doing things 2000 times makes the fingers to for the 'feeling' more than anythings else.

Worth every minute when you get "the feeling".
Title: Re: Attaching plastic valves
Post by: george garside on July 04, 2016, 05:19:29 PM
now't like a good 'feel'!

george ;)
SimplePortal 2.3.5 © 2008-2012, SimplePortal