Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: JNM SY on September 04, 2016, 02:20:30 PM

Title: Trichord Mixte
Post by: JNM SY on September 04, 2016, 02:20:30 PM
This is my attempt at a "mixte"box. I (ab)normally play an Elite3, but constant arm ache is forcing me to seek a lighter alternative. The trichord works quite well but the bass end uses a lot more air than the original 12 bass. I added a Bmin chord but still miss the counter basses.
Title: Re: Trichord Mixte
Post by: george garside on September 04, 2016, 03:57:34 PM
did you do the conversion yourself if so can you post pics of how you adapted the  bass end to fit the trichord bellows

george
Title: Re: Trichord Mixte
Post by: JNM SY on September 04, 2016, 04:49:47 PM
I did the work myself but I didn,t take any other photos.
From the start I wanted everything I did to be reversable,so if it didnt work out I could easily put the original bass side back on.
  I started by building a frame (using 12mm square hardwood) round the bellows frame,clamping it firmly overnight so when it dried it would be a tight fit.Half lap joints at the corners.
Repeat the process building a frame inside the bass side.
In this case the height was almost the same.
  Glue the two frames together,with the difference in width at the rear of the box. I then filled the gap between the two frames by inserting a 2 mm plywood board in the bellows side just cutting a hole out of the middle after the glue dried .There was enough clearance left for the bellows to plug in fully over the top of the plywood.  Here,s pic of the back showing the difference in sizes.
 I found this way easier than trying to cut an adapter plate out of one sheet of ply, and if you clamp the wood frames carefully (while the glue is wet obviously) then you,ll get a good fit.
                    JNM SY.
PS  Scrap bits of celluloid were used to cover the exposed ply and frame visible at the back.
Title: Re: Trichord Mixte
Post by: Andy on September 04, 2016, 10:19:42 PM
"I added a Bmin chord but still miss the counter basses."
 
Just wanting to check then, do these 4 row student basses have:           bass,                  chord,      minor,         7 th
Rather than:                                                                              counter bass,           bass,       chord,        minor
Title: Re: Trichord Mixte
Post by: JNM SY on September 05, 2016, 12:52:53 AM
Yes- bass, maj chord, min & 7 th. No counterbass.
Ideally I would have used a 40 bass donor box, but as far as I know there aren,t any to match this model of trichord.
 I could have rearranged the reeds I suppose to get Bmin by
Sacrificing the Eflat at the other end, but as there was one space left in the bass machine, I thought that would be an easy option to stick in another bass key- the required reeds for the chord are already there.( Not the bass reeds though).
 In  fact it took ages filing down an old bass rod that was too wide and also too thick to fit in the slots.

Took some more pics.The unfinished frame closest to the camera is the smaller frame built INSIDE the new bass.
The other frame was built around the outside of the original bellows. (Smoothed over and painted dark red)The two frames are positioned so that the both sides are even at the top and bottom when assembled and glued together.The 2 mm plywood is then used fill the space between the frame sizes.
Title: Re: Trichord Mixte
Post by: JNM SY on October 26, 2017, 11:33:15 PM
Another version.This one suits me better as it has counter basses.( and a few extra ones I added myself)
Title: Re: Trichord Mixte
Post by: Rog on October 26, 2017, 11:53:46 PM
What is the tuning on the RH? DG plus accidental row?
Title: Re: Trichord Mixte
Post by: JNM SY on October 27, 2017, 12:01:06 AM
No,it was originally C F Acc, but I converted it to BCC# as that is the system I play. I tried the CF system and it has advantages but I think I,m too old to learn another system now.
SimplePortal 2.3.5 © 2008-2012, SimplePortal