Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: mselic on August 08, 2017, 10:06:49 PM

Title: broken screw in keyboard
Post by: mselic on August 08, 2017, 10:06:49 PM
Without much warning, the screw that fastens the keyboard to the frame on my Hohner HA114 broke as it was going back in.  I now have one half of the screw stuck in the keyboard thread.  Not sure what my options are here...I suppose a screw extractor, but even if I do manage to get it out, how would I attach the keyboard now?
Title: Re: broken screw in keyboard
Post by: playandteach on August 08, 2017, 10:20:55 PM
Can I just say that I paid a lot of money for a screw extractor set, used it successfully and mislaid it. I bought a cheap set which was totally hopeless. One product where the quality of metal matters.
Title: Re: broken screw in keyboard
Post by: Theo on August 08, 2017, 10:38:36 PM
If you get the broken screw out you need M3 x 30mm screw. It's rather a small diameter to get a screw extractor into. There other ways of removing screws - cut a slot in the broken end and use a screwdriver; use a small pointed tool (centre punch) to turn the screw enough to grasp the end with pliers.
Title: Re: broken screw in keyboard
Post by: Winston Smith on August 08, 2017, 10:47:32 PM
If it's the plastic keyboard, and the screw is stuck in the captive nut, you're just about b******d I'm afraid. The only reason which I can think of that the screw would snap, is that it was cross threaded, which will have spoilt the captive nut. Although, I suppose that it would be possible, if you managed to get the broken bit out, to drill and re-tap the captive nut and use a bigger screw to fasten it together again. Not particularly easy, I'm afraid.
Title: Re: broken screw in keyboard
Post by: Theo on August 08, 2017, 11:08:17 PM
Or maybe drill out the whole captive nut and fix a new on in with epoxy.  Probably best to replace the keyboard with one of these.

http://www.acorninstruments.co.uk/inst.cfm?instID=24
Title: Re: broken screw in keyboard
Post by: george garside on August 08, 2017, 11:30:16 PM
.  You don't say whether the keyboard is off the box or not?    If it is still partly attached the screw at the other end of the keyboard screw out  so that the keyboard can be removed in its entirety?.  If this is the case  there may then be sufficient of the broken screw protruding from the keyboard to get it out with mole grips.  If the keyboard is off the box and the broken screw is not protruding it may be possible to drill it out carefully , preferably using a  bench  drill press , and then tap the captive nut  a size larger. or if this is not possible to araldite a short length of threaded bar ( ? a  ?m  3screw with the head cut off?) into what remains of the captive nut.  this could then be secured by a nut inside the box.

george
Title: Re: broken screw in keyboard
Post by: syale on August 08, 2017, 11:52:00 PM
Or maybe drill out the whole captive nut and fix a new on in with epoxy.  Probably best to replace the keyboard with one of these.

http://www.acorninstruments.co.uk/inst.cfm?instID=24

Bit tricky fitting a 2 row keyboard on a one row Hohner (HA-114)
Stephen
Title: Re: broken screw in keyboard
Post by: Winston Smith on August 08, 2017, 11:59:02 PM
"Bit tricky fitting a 2 row keyboard on a one row Hohner (HA-114)"

But novel, Stephen. Could be the start of a new trend?
Title: Re: broken screw in keyboard
Post by: mselic on August 09, 2017, 12:04:34 AM
The keyboard is off, and a luthier friend of mine and I spent an hour or two getting what's left of the old screw out. We're now looking at drilling out a new thread for a slightly larger screw. I'll let you know how it goes...
Title: Re: broken screw in keyboard
Post by: Winston Smith on August 09, 2017, 12:13:20 AM
Sounds as if a new keyboard would be cheaper.
Title: Re: broken screw in keyboard
Post by: Steve_freereeder on August 09, 2017, 01:18:29 AM
Charlie Marshall (http://www.cgmmusical.co.uk/CGM_Musical_Services/Welcome.html) sells a replacement keyboard (http://www.cgmmusical.co.uk/CGM_Musical_Services/Hohner_Parts.html#30) for a Hohner 114.
Title: Re: broken screw in keyboard
Post by: mselic on August 09, 2017, 01:28:12 AM
Success! We managed to use a tap and die set to drill a new thread slightly wider than the last and used the corresponding sized screw to fasten it back in place! It only cost me a case of beer, a few hours with a good friend, and I still get to use the accordion this evening as planned! Thank you everyone for your input - much appreciated and helpful.
SimplePortal 2.3.5 © 2008-2012, SimplePortal