Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Tiposx on January 17, 2018, 03:47:46 PM
-
I have just modified my toy plastic 7 button melodeon into a single voice in the key of D. (originally brass reeds in the key of C) The Cagnoni reeds are quite a bit longer than standard, so I had to make a new reed block. It really sounds very pleasant and doesn't use much air. It sounds quite similar to a concertina. The volume is quite low - I can talk over it if needed, which is just what I wanted. I tour in a tiny caravan for 13 weeks of the year, so for me this is an ideal instrument. My layout is key 2-8 of a normal single row, so it is a button 2 start. There was no room for the "bass" reeds, so I have removed that reed block altogether.
-
Neat work
-
I had to make a new reed block.
Could you elaborate on that please?
-
The original plastic reed block is not tall enough for the reed plates I wanted to use, so I made a new block to suit.
-
I understand. I was hoping you might tell us how you made it.
-
Ok - I made the base plate from ply same exactly the same size as the original, drilled holes to match the fondo. Then I attached the centre plate with a fillet at the back. Then the slanted top strip from pine as dictated by the heights of the first and last reed plate, followed by the vertical reed chamber dividers, sanded to the correct angle at the top . Added some strengthening fillets at the back - that's about it. I didn't cut rebates for the uprights in view of the nature of the project. Titebond feels plenty strong enough for this project.
The photo is of a dummy reed block I used to tune my Hohner 1140, but it gives you the idea.
-
More photo please. How about the airbutton? And the bellows?
I like the thing!
-
Very good! Did you do anything with the bellows in order to improve it?
-
I used to think that the air loss was due to leaky bellows, but it was actually the bass end pallets leaking. I taped over the holes and it was loads better. Bass reeds now removed and holes sealed. The bellows needed a good overnight stretch when new. Since then I have just played it a lot over the last 6 months or so and the bellows have improved plenty. I bought another new one recently and I could hardly pull the bellows open! I had forgotten how poor they were.
Other mods - have fitted a bass strap that fits my left hand. Also replaced the metallic grille cloth with the real stuff, which actually made a difference.
I will post some more photos later.
-
The big problem with the bellows is in the gussets. They're made of a thin, treated, fabric that soon fails to seal and they become porous. :(
Have you seen all the threads about improving/rebuilding these toy melodeons? They'll show up if you perform a forum search for "Chanson"...
-
Hi triskel yes I have seen those threads. I haven't seen any examples using good reeds or new reed blocks though. The other mod I tried with the original reeds was tuning it completely dry. It sounded really super, but within a couple of days the tuning drifted and it just sounded "good", but it showed the potential of the instrument.
-
Photos as requested:
The Tobar in all its glory with new grille cloth:
-
I haven't seen any examples using good reeds or new reed blocks though.
Here's one! (https://www.youtube.com/watch?v=PfvCxfBH7j8)
-
Bass strap:
-
Fondo with 2 holes (for two reeds) and base of new reed block for single voice.
-
Close up of new reed block. The panel on the rear is where I added volume to the largest 2 reed chambers. I am still experimenting with this, also I suspect that the hole in the fondo/ reed block for those 2 reed plates may benefit from a slight enlargement.
-
Hi Pearse Rossa thanks - that clip shows what can be achieved.
-
Back to the good old Chanson post! I did all kinds of daft things to Chansons back in the day, stripping off the plastic, doubling up on the bellows etc. Getting Microbot to fit out a couple with Hohner reeds really worked, and now that I’m so decrepit and can’t play my 114’s they have come into their own as the only boxes I can play. The sound is great and very loud. Two coats of PVA pretty well cured the porous gussets by the way. Lester retuned one with the original reeds to Bb and that is surprisingly good.... :||: (:)