Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Henry Piper on March 29, 2018, 05:57:37 PM

Title: Pokerwork Gaskets.
Post by: Henry Piper on March 29, 2018, 05:57:37 PM
I have just acquired most of an almost new, Chinese Pokerwork box, courtesy of a fellow melnetter, and I am planning to install a set set of old or even "Vintage" reeds in it. The FondoPalletteboardsoundboardthing has the gasket for the reedblocks attached to it, the reedblocks  I'm planning to use also have gasket material attached,.....What is my best plan of action:-
                    1     Remove reedblock gasket retaining Fondo gasket.
                    2     Remove fondo gasket retaining reedblock gasket
                    3    Leave both in place

If it helps the reedblock gaskets are a little worn, but the fondo gasket, being virtually new is pristine.
Cheers    Henry.
Title: Re: Pokerwork Gaskets.
Post by: John MacKenzie (Cugiok) on March 29, 2018, 06:01:16 PM
I would clean off the new reed blocks, as that lessens the chance of damaging the fondo.

SJ
Title: Re: Pokerwork Gaskets.
Post by: Lester on March 29, 2018, 06:02:45 PM
I have always removed the gasket from the reed blocks, mainly because it is easier. Scrape off as much of the gasket as you can then sand on a flat surface to true up the face of the block. It may be necessary to add some thickness to the tongue of the reed block that fits under the casework to ensure a tight fit.
Title: Re: Pokerwork Gaskets.
Post by: Andy Next Tune on March 29, 2018, 07:57:49 PM
Out of curiosity, how would you approach the opposite problem - no gaskets on either.

Where is it best to place the Olovisc gasket from CGM - fondo or blocks?

I think my long term project box sitting on the shelf will have this challenge.
Title: Re: Pokerwork Gaskets.
Post by: Theo on March 29, 2018, 09:06:28 PM
In that case I woouldput gasket on the block, just because it’s a bit more accessible.  Stick on a full sheet, then cut the coles out with a scalpel.
Title: Re: Pokerwork Gaskets.
Post by: Lester on March 29, 2018, 10:48:29 PM
In that case I woouldput gasket on the block, just because it’s a bit more accessible.  Stick on a full sheet, then cut the coles out with a scalpel.

I did it the other way but as I had the casework without any of the mechs fitted so it was easy enough.
Title: Re: Pokerwork Gaskets.
Post by: tirpous on March 30, 2018, 12:45:56 AM
Quote
Quote from: Theo on Yesterday at 09:06:28 PM

In that case I woouldput gasket on the block, just because it’s a bit more accessible.  Stick on a full sheet, then cut the coles out with a scalpel.

I did it the other way but as I had the casework without any of the mechs fitted so it was easy enough.

Or one could compromise and put 1 gasket on the block and the other one on the fondo !   ;D

More seriously: I'm fixing a Pokerwork for a friend and one of the blocks seems to have warped so it leaks at the base.  I think I'll have to remove/replace the gasket from the block to fix it.  Wouldn't be necessary if the gasket was on the faceplate (fondo)...
Title: Re: Pokerwork Gaskets.
Post by: boxcall on March 30, 2018, 01:29:44 AM
On the recording king I just did some work on, the gasket was on the fondo on the treble side and on the blocks on the bass. Different colored material so maybe one of the sides was redone at one point.
Six of one - half dozen of the other.
Title: Re: Pokerwork Gaskets.
Post by: Theo on March 30, 2018, 07:55:41 AM
Exactly,  and fondos can warp too.
Title: Re: Pokerwork Gaskets.
Post by: Henry Piper on April 02, 2018, 06:38:08 PM
Thank you all for the advice.   As suggested  I shall be removing the gasket material from the reed blocks and leaving it on the fondo.
SimplePortal 2.3.5 © 2008-2012, SimplePortal