Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Peadar on January 12, 2019, 03:08:07 PM

Title: Stop Lubrication
Post by: Peadar on January 12, 2019, 03:08:07 PM
Recently aquired an antique single row. (Antoria Tremelo, 3 stop if you ignore the tremelo valve).

Stops are very stiff- It took me a good five minutes to open them up at first- I was actually afreaid of breaking something in the process.- Investigation showed the stop push rods had corroded into the wood. A couple of days use and they move, but force is still a bit excessive.

Thinking of trying a (small) drop of raw linseed oil on each might help. Any views on the wisdom or otherwise?

The logic being that linseed oil is used in the conservation of wooden artefacts.
Title: Re: Stop Lubrication
Post by: Theo on January 12, 2019, 03:12:37 PM
Nope.  It will work to begin with then when dust begins to stick to the oil it will gradually get stiffer.  In addition linseed oil oxidises and hardens over time. 

First make sure that the steel rod is cleaned of all traces of rust, then if it's still stiff apply some powdered graphite, or powdered ptfe.   
Title: Re: Stop Lubrication
Post by: Peadar on January 12, 2019, 03:18:52 PM
Thanks Theo - That makes perfect sense.
Title: Re: Stop Lubrication
Post by: Scotty Gring on February 13, 2019, 01:39:14 AM
Nope.  It will work to begin with then when dust begins to stick to the oil it will gradually get stiffer.  In addition linseed oil oxidises and hardens over time. 

First make sure that the steel rod is cleaned of all traces of rust, then if it's still stiff apply some powdered graphite, or powdered ptfe.

Theo - can you briefly explain to this newbie the dos/don'ts regarding graphite?  I thought I had seen elsewhere not to use it but it was likely a situational type thing.  Seems like it would be good, but I assume there are some places where it shouldn't?  I better ask now because you haven't seen the mess I can make with a tube of graphite.
Title: Re: Stop Lubrication
Post by: Steve_freereeder on February 13, 2019, 01:55:26 AM
If you are a bit clumsy with the graphite, it can leave a dark residue on exposed surfaces, but I can't think of any places where it should never be applied if ultimately required as a lubricant. Keep it away from reeds and valves, I guess...

It's best to use locksmiths' graphite which should be a very fine dry powder (usually supplied in a squeezy puffer-type container) rather than in a squirty or tube version which may be mixed with a propellant of some sort.

Put some dry graphite powder in a small dish or saucer or similar, then mix it with a little methylated spirit. Use a small pointed artists' paint brush or similar to apply small amounts of the graphite/spirit suspension to the problem area on the instrument. The alcohol acts as a carrier to get the graphite into hard-to-reach areas, then evaporates leaving the graphite in place.
Title: Re: Stop Lubrication
Post by: Martyn on February 14, 2019, 09:54:27 PM
Probably easiest and most effective to rub a parrafin wax candle on the stop rod.

Martyn
Title: Re: Stop Lubrication
Post by: Kimric Smythe on February 17, 2019, 07:49:04 PM
I remove the rust with very fine sandpaper and then rub the rod with a wax candle (not bees wax in this case).
This will not draw dust and will also slow down rust. Works great to keep the rods from sticking.
SimplePortal 2.3.5 © 2008-2012, SimplePortal