Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Mark Leue on April 05, 2019, 11:11:00 PM

Title: Condition of reeds
Post by: Mark Leue on April 05, 2019, 11:11:00 PM
Here's a reed block from a presswood Hohner CF I'm learning to work on.
As you can see it has mixed age reeds, with a couple of zinc blocks.
Questions: What are the chances that Hohner did this originally, or is it a repair?
Is the oxidation and some rust pitting on the reeds bad enough to worry about?
Anything else about them other than the missing valves that you notice?  thanks.
(http://)
Title: Re: Condition of reeds
Post by: Eshed on April 05, 2019, 11:23:18 PM
I have a Club IIB Victoria with mixed age reeds as well, no idea what this says, though :D
Title: Re: Condition of reeds
Post by: Theo on April 06, 2019, 12:07:59 AM
That looks like the original Hohner setup to me. I’ve seen many examples of mixed aluminium and zinc reeds on the same block and with every indication that they are original.

I don’t see any missing valves.  The highest two or three reeds on each block don’t usually have valves - they work better that way.  If in doubt look for traces of old glue which you will be able to see if there were valves which have got lost.
Title: Re: Condition of reeds
Post by: Mark Leue on April 06, 2019, 02:08:01 PM
Thanks, interesting.

How about that corrosion? Not a big deal?
Title: Re: Condition of reeds
Post by: Theo on April 06, 2019, 02:24:29 PM
Not enough corrosion to affect reed performance,  but worth cleaning off when you take the reeds off the blocks.
Title: Re: Condition of reeds
Post by: Peadar on April 06, 2019, 02:34:16 PM
Quote
That looks like the original Hohner setup to me. I’ve seen many examples of mixed aluminium and zinc reeds on the same block and with every indication that they are original.

Question for Theo...

Do you have any idea of the approximate ages of the boxes with mixed reed plates?

In the early post war years - certainly up to the mid fifties British manufacturing faced serious difficulties with regular  material supply. It would be no surprise to find that the other European economies were in the same boat.
It may well have been the case that in that period the punching machines used to mass produce the reed plates could have been running off some batches in Aluminium and others in zinc.
Title: Re: Condition of reeds
Post by: Theo on April 06, 2019, 02:41:31 PM
Could be.  It could also be that there were varied stock levels of different size reed plates.  The new aluminium plates just came in as individual sizes of zinc plates were exhausted.
Title: Re: Condition of reeds
Post by: Peadar on April 06, 2019, 09:56:22 PM
Does anyone have any idea when Hohner switched from Zinc to Aluminium? 
Title: Re: Condition of reeds
Post by: Theo on April 06, 2019, 10:28:58 PM
My best guess it was over the 30s/40s/50s, I don’t think it happened over a short period. It’s not unusual to find mixes like yours, and more common to find zinc treble reeds with aluminium bass reeds.
Title: Re: Condition of reeds
Post by: Mark Leue on April 07, 2019, 03:02:57 AM
Not enough corrosion to affect reed performance,  but worth cleaning off when you take the reeds off the blocks.

Suggestions for an effective method when both sides of the reed are available? 0000- steel wool? 

Thanks.
Title: Re: Condition of reeds
Post by: Jesse Smith on April 07, 2019, 03:21:07 AM
I don't know if there's any connection but low-denomination German coins were made of zinc from 1940 until the end of the war (presumably bronze was needed for war materials or was just too expensive for a wartime economy). I wonder if that could have disrupted supplies or prices and encouraged the change.

I believe my 1950s presswood has a mixture of reed plates, too. I think I read that one way to date the boxes is by the domed "feet" on the bass side. If they are separate from the screws that hold on the panel, it is a post-war box. If the feet are held on by those same screws, it is earlier. But someone please correct me if I've got that wrong.
Title: Re: Condition of reeds
Post by: Theo on April 07, 2019, 07:26:05 AM
Not enough corrosion to affect reed performance,  but worth cleaning off when you take the reeds off the blocks.

Suggestions for an effective method when both sides of the reed are available? 0000- steel wool? 

Thanks.

Not steel wool it’s horrible stuff, and fibres can easily get stuck in the reed gap.

I use an abrasive polishing block like this https://www.cooksongold.com/Jewellery-Tools/-Range=Polishing_Materials/-Size=0/-Type=Abrasive_Blocks/-Brand=0/-Font=0/&prdsearch=y
SimplePortal 2.3.5 © 2008-2012, SimplePortal