Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: AlexCJones on July 08, 2019, 01:52:23 AM

Title: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: AlexCJones on July 08, 2019, 01:52:23 AM
I have read a bunch of posts about the bending needed to restore the button height after resurfacing the pallets with thick material, but I still am not sure exactly how to do that.  (I have not yet started resurfacing the pallets, but the material I have is 2.5-3mm thick, and will certainly make the buttons low enough that I will need to do the bending to restore their height.)

From some posts, it seems like the arm going from the button to the fulcrum rod is what is to be bent, but from others, it seems like it is the portion from the fulcrum rod to the pallet.  So, at what point should the bending be done?  It other words, is it the short part of the "L" or the long part?  And what part of the short or long part?

Does anyone have any instructions with a photo showing the best way to do the bending part?  I looked on YouTube for a video, and even with "accordion" in the search, but the results are videos for bending all kinds of non-musical machine parts, but not accordion levers.  Would anyone know of a video that exists, that I just have not found yet?

Thanks.


Title: Re: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: boxcall on July 08, 2019, 02:37:29 AM
The bending happens on the button side of the arm,

Watch this guy (  I think he’s some kind of MD ) about fourteen minutes in or watch the whole thing as it applies.
https://m.youtube.com/watch?feature=youtu.be&v=g7nVDIXF3qc
Title: Re: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: Lester on July 08, 2019, 08:04:37 AM
Watch this guy (  I think he’s some kind of MD ) about fourteen minutes in or watch the whole thing as it applies.
https://m.youtube.com/watch?feature=youtu.be&v=g7nVDIXF3qc (https://m.youtube.com/watch?feature=youtu.be&v=g7nVDIXF3qc)


He's good, who is he?
Title: Re: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: Squeaky Pete on July 08, 2019, 09:19:23 AM
Don't assume automatically that you are going to have to do a lot of work. If the old pallets have been removed without bending the arms, not much will change. I only had to bend 3 or 4 on my club III B S and I had to take the whole mechanism out to get the pallets off to start with.
Title: Re: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: Winston Smith on July 08, 2019, 09:33:47 AM
Surely, by just bending the button end of any linkage, that would leave the pallet sitting at an angle on the soundboard/fondo thingy, begging air to leak past?
Title: Re: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: Lester on July 08, 2019, 09:40:06 AM
If you watch my video (above) I recommend adjusting the button height and checking button alignment prior to hot glueing the pallets in place
Title: Re: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: rees on July 08, 2019, 10:10:38 AM
As Lester says, get everything lined up and in the right place before applying the glue.
Title: Re: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: Steve_freereeder on July 08, 2019, 11:43:16 AM
Surely, by just bending the button end of any linkage, that would leave the pallet sitting at an angle on the soundboard/fondo thingy, begging air to leak past?
It doesn't though. When the pallets (with new facing) are in position over the fondo vents, and with the lever arms bent slightly to restore the previous button height, the lever arms then slot into place into the pallets at a fractionally different angle than previously. That new angle is then preserved when you glue the lever arms on to the pallets. Watch Lester's video - it is spot on.

If you have only refaced 1-row 4-stop pallets, they are longer and therefore slightly more tricky to get a flat, flush seal all along the length of the pallet. Hence the potential for air leaks is greater. But if you follow Lester's method you should be OK.
Title: Re: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: AlexCJones on July 09, 2019, 03:12:37 AM
Thanks Mr. Bailey or Dr. Bailey!

This video is EXACTLY what I need!  It also answers the questions I would have needed to ask later, too.  It also takes the fear out of it.

Hey everyone! 

He has made a whole SERIES of videos called "Hot Rod a Hohner"!  This video above is #2 in the series and #3 is restricting the treble action.  There is also one for resurfacing the bass pallets and one for retaping the bellows too.  Just go to YouTube and enter "Hot Rod a Hohner" in the YouTube search field.

Thanks again!  This video series is brilliant!
Title: Re: How to bend pallet Lever arm on HA-2814, HA-2915, Pokerwork, 2-Row?
Post by: Tone Dumb Greg on July 09, 2019, 09:11:27 AM
Thanks Mr. Bailey or Dr. Bailey!

Hey everyone! 

He has made a whole SERIES of videos called "Hot Rod a Hohner"!

New readers start here (it's as good a place as any)

http://forum.melodeon.net/index.php/topic,23627.msg281500.html#msg281500

Would it be feasible to include a link to Lester's Hot Rod on the Home page?
SimplePortal 2.3.5 © 2008-2012, SimplePortal