Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: baz parkes on August 11, 2019, 12:15:39 PM

Title: Retaping Bellows...Again
Post by: baz parkes on August 11, 2019, 12:15:39 PM
Ok...after countless viewings of Lester's video and weeks of procrastination I've taken the bellows off my pressedwood with a view to retaping.

The current tape isn't your standard gold but a matt black...(the bellows are green...) and it seems rather reluctant to part company with the bellows. I'm reluctant to use too much brute force (combined with rather a lot of ignorance...) as I don't want to damage the bellows themselves.
Might gentle dampening help in this case or am I being over cautious?

Concerned of Mobberley.
Title: Re: Retaping Bellows...Again
Post by: Steve_freereeder on August 11, 2019, 01:45:21 PM
Gentle dampening is OK. Use a damped sponge or cloth to moisten the bellows tape. Work on a single fold at a time. Leave for a couple of minutes after dampening and then try to carefully peel and lift off the old tape using a blunt knife or scraper. With luck you should be able to remove a long-ish section of tape. Re-dampen as needed, but take care not to saturate the bellows fold.

It's a horrible messy job and needs a lot of patience. Good luck!
Title: Re: Retaping Bellows...Again
Post by: Theo on August 11, 2019, 04:51:12 PM
I'm more adventurous than Steve!  I spray the bellows with a fine mist sprayer and do a whole side at a time.  If you hold the bellows by one end so it hangs down with the fold slightly open it is possible to control where most of the spray lands.   Do it from both sides, then close the bellows, put it in a plastic bag and leave for 20 minutes.  If the tape doesn't come off easily repair the spray and wait.
Title: Re: Retaping Bellows...Again
Post by: Winston Smith on August 11, 2019, 11:38:53 PM
Theo, you terrify people!
Title: Re: Retaping Bellows...Again
Post by: Nick Collis Bird on August 12, 2019, 07:20:51 AM
Agree with Steve and Theo. Even if you over spray Baz if won’t do any damage.
  Let’s just hope that if it had been retaped  before, that person used water soluble adhesive . 🙏
Title: Re: Retaping Bellows...Again
Post by: Peadar on August 12, 2019, 07:22:46 AM
I'm more adventurous than Steve!  I spray the bellows with a fine mist sprayer and do a whole side at a time.  If you hold the bellows by one end so it hangs down with the fold slightly open it is possible to control where most of the spray lands.   Do it from both sides, then close the bellows, put it in a plastic bag and leave for 20 minutes.  If the tape doesn't come off easily repair the spray and wait.

Fine mist sprayer.....like a greenhouse/houseplant mist sprayer running on pure unadulterated Adam's Ale?
Title: Re: Retaping Bellows...Again
Post by: Theo on August 12, 2019, 08:52:13 AM
The one I use is a repurposed cosmetic bottle of some kind,  but any kind of spray bottle will do.
Title: Re: Retaping Bellows...Again
Post by: baz parkes on August 12, 2019, 09:07:54 AM
Thanks all...I've managed to do 4 folds so I'm at the point of no return... >:E
Title: Re: Retaping Bellows...Again
Post by: Lester on August 12, 2019, 10:31:15 AM
Thanks all...I've managed to do 4 folds so I'm at the point of no return... >:E
My thoughts are with you at this difficult time
Title: Re: Retaping Bellows...Again
Post by: baz parkes on August 12, 2019, 11:23:16 AM
Thanks all...I've managed to do 4 folds so I'm at the point of no return... >:E
My thoughts are with you at this difficult time
Should anyone be thinking of undertaking this task, your Granny's old butter knife will prove invaluable. (Other elderly female residents may be available...or indeed male....) :|glug
Title: Re: Retaping Bellows...Again
Post by: Steve_freereeder on August 12, 2019, 11:28:16 AM
Thanks all...I've managed to do 4 folds so I'm at the point of no return... >:E
My thoughts are with you at this difficult time
Should anyone be thinking of undertaking this task, your Granny's old butter knife will prove invaluable.
Snap! Bingo! (etc.) That's exactly what I use!
Title: Re: Retaping Bellows...Again
Post by: baz parkes on August 12, 2019, 01:30:44 PM

  Let’s just hope that if it had been retaped  before, that person used water soluble adhesive . 🙏

Seem to have done...comes o4f in two layers...the black top leaving behind the white was sticky bit... :|glug
Title: Re: Retaping Bellows...Again
Post by: baz parkes on August 12, 2019, 04:14:31 PM
Should anyone be thinking of undertaking this task, your Granny's old butter knife will prove invaluable.
Snap! Bingo! (etc.) That's exactly what I use!
"Warranted Sheffield Manufacture" I trust? :|glug
Title: Re: Retaping Bellows...Again
Post by: Steve_freereeder on August 12, 2019, 06:39:58 PM
Should anyone be thinking of undertaking this task, your Granny's old butter knife will prove invaluable.
Snap! Bingo! (etc.) That's exactly what I use!
"Warranted Sheffield Manufacture" I trust? :|glug
Of course!
Title: Re: Retaping Bellows...Again
Post by: Peadar on April 11, 2020, 10:12:57 PM
Advice needed (before I try this on a set of bellows that matter) ::):

A couple of my acquisitions absolutely need at least some of the bellows tapes replaced. Not a job I've done before.

A search for a fine mist sprayer ended with the realisation that the choice available to me is a 20 litre backpack model last used for spraying thistles or an old windolene bottle.

I have tried a wall paper steamer instead- experimenting on a section of scrapped PA bellows.  The steaming pipe is a piece of 20mm toilet overflow pipe with a quarter section cut out of it that saddles over one fold at a time

The tapes in question appear to be fabric based, attached with a hot glue. 30 seconds of steam then start peeling. When the tape starts resisting repeat steaming. Or maybe go onto the next fold to avoid soaking damage to the underlying bellows paper? First two folds shown after stripping...one of them part of the bellows paper has failed before the glue did.

Is the damage to the bellows paper in the normal range for the tape stripping operation or is the method just too viscious for this job?




Title: Re: Retaping Bellows...Again
Post by: Theo on April 11, 2020, 10:27:33 PM
Looks good to me.
Title: Re: Retaping Bellows...Again
Post by: Peadar on April 11, 2020, 10:51:57 PM
Looks good to me.
Thanks Theo. Not perfect but I'll practice on the other folds/sides before I go for the real thing.
Title: Re: Retaping Bellows...Again
Post by: mselic on April 12, 2020, 01:43:10 AM
I use Theo’s method and it has worked every time.
Title: Re: Retaping Bellows...Again
Post by: Theo on April 12, 2020, 09:15:44 AM
With older boxes like your Club you can often pull off the tape without any need for steam or water spray.  If you can see a corner that is not firmly glued try lifting it and pulling.  If that does work it much less messy.
Title: Re: Retaping Bellows...Again
Post by: Julian S on April 12, 2020, 10:07:22 AM
I'm pleased that I've got some tape somewhere for essential repairs - and I think that this is a good time to find it and get the bellows in order for whenever we are let out again.
(I can probably guarantee that I haven't quite enough tape or adhesive for all the repairs - such is life !)
Certainly my experience has been that old tape can be quite easy to take off without damping it - probably shouldn't say that because I'll now find the next repair much more problematic. And the old favourite round ended butter knife has proved very useful both in helping remove tape and apply glue (though I advise careful cleaning before returning to the kitchen drawer ! ::))

J
Title: Re: Retaping Bellows...Again
Post by: MikeK on April 12, 2020, 10:56:28 AM
With older boxes like your Club you can often pull off the tape without any need for steam or water spray.  If you can see a corner that is not firmly glued try lifting it and pulling.  If that does work it much less messy.

I have retaped several and found that by gently lifting a corner, the tape comes away,tearing in two along the spine. I also tend to hold the tape flat in the direction of travel. This method has always worked for me.
Title: Re: Retaping Bellows...Again
Post by: Lester on April 12, 2020, 12:35:17 PM
I have retaped many, mostly Hohner, boxes and indeed sometimes the tape just peels off easily with no tearing of residue, but the other 75% if comes off in little bits leaving glue/paper residue that has to be wetted to remove. Tis the luck of the draw

Title: Re: Retaping Bellows...Again
Post by: Theo on April 12, 2020, 01:01:55 PM
If the tape is paper as on more recent Hohners. Then my experience is similar to yours Lester,  But for older Hohners with cloth tape,  like the club Vic, the experience is different.
Title: Re: Retaping Bellows...Again
Post by: Peadar on April 12, 2020, 03:23:05 PM
I have no idea what the bellows I was practising on came off- but the tapes were obviously fixed with a hot aimal glue (tackiness post heating and smell).
The first box to be retaped   is a Pancotti probable date range 1935-50 and appears to have bellows covered in cloth rather than paper. The second is a (possibly Hohner built) Wilkinson Execelsior c.1926.

Title: Re: Retaping Bellows...Again
Post by: Rog on April 13, 2020, 07:30:22 AM
I avoid retaping as much as possible  (:)
Title: Re: Retaping Bellows...Again
Post by: Graham Spencer on April 13, 2020, 09:50:41 AM
I avoid retaping as much as possible  (:)

Agreed, but sometimes it's unavoidable.......
Title: Re: Retaping Bellows...Again
Post by: Peadar on April 14, 2020, 07:31:21 PM
I have no intention of completely retaping the bellows just for the fun of it, but both boxes have been well played by original (or at least former) owners.  and bellows tape has worn through in places which belie the strapping/posture preferences of owners. Those sections of bellows tape need replaced to enable refettling to at least medium term playability.
Title: Re: Retaping Bellows...Again
Post by: MikeK on April 14, 2020, 08:23:29 PM
I must be in minority as I find retaping relaxing and enjoyable. Especially when I cast a critical eye over the final result and end up rather pleased
with the result.
Title: Re: Retaping Bellows...Again
Post by: Nigel.H on April 14, 2020, 09:07:13 PM
I recently contemplated a full tape and paper refinish of a Presswood bellows, the one with the very thin pale green paper and 'ruddy' coloured tape.  Ruddy was right.  Lester counselled against a full re-furb ( at The Fleece ) and I fully intended to follow his advice.

But, .....the tape was fixed with rabbit/hide/fish glue and it flatly refused to peel.  The moistening - done with a damp cloth - moistened in turn the paper which was happy to come away jut for being looked at! and as the tape glue refused to let go in places, the paper was coming off before or with the tape.  I ended up completely re-finishing the bellows, down to the card.  It was quite fulfilling as it happens - a pain - and a long job, but it was winter.  It has rejuvenated the bellows which are now very responsive.  I got the paper from one of the German Hohner parts places.....made a template for the 'V's from a tin lid.  The corner pieces were pretty straightforward to ease off and re'pinch'. 

That 'certain era' Presswood paper is very thin compared to later bellows and much weaker than the tape.  I think the refurb was worth the effort/expense, especially for the playability of the bellows, if not the improved looks. 
Title: Re: Retaping Bellows...Again
Post by: Peadar on April 14, 2020, 09:55:42 PM
I really don't want to trash this bellows paper:See below
Title: Re: Retaping Bellows...Again
Post by: Nigel.H on April 14, 2020, 11:34:46 PM
Interesting - original ?.....this one was listed this week, on DE.  Unusual celluloid finish and jazzy bellows.  Not sure if original or not.
Title: Re: Retaping Bellows...Again
Post by: Theo on April 15, 2020, 08:55:32 AM
Yes that is a paper I’ve seen several times on early 1930s Hohners.
SimplePortal 2.3.5 © 2008-2012, SimplePortal