Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Dazbo on January 16, 2008, 12:45:27 PM

Title: Blown Reed?
Post by: Dazbo on January 16, 2008, 12:45:27 PM
A bass reed on my Tommy seems unwell.  On the A note at low volumes all is fine but when giving it some welly for morris the low reed randomly does one of: a) plays fine, b) sounds well out of tune, c) doesn't play at all.

I've not had a change to get the box apart yet but assuming I can't see any problems I want to make sure I've done all I can before I trek up to The Music Room at Cleckheaton.

Cheers,
Title: Re: Blown Reed?
Post by: george garside on January 16, 2008, 12:54:47 PM
HOpefully Theo will come in  with his considerable expertise  on this one . For what its worth my first shot would  be to put a great deal of pressue on the bellows first and then press the appropriate button to play the offending reed suddenly long & loud., perhaps repeating this several times - this may dislodge a moving bit of dust, wax or whatever that may be intermitantly jamming the reed (as sometimes it is not sounding). If this  non invasive therapy doesnt work work open it up, remove reedblock & 'ping' the offending reed several times until the 'ping' sounds more musical. After that its on to the 'expert' stuff.

george
Title: Re: Blown Reed?
Post by: Dazbo on January 16, 2008, 01:03:52 PM
Hi George, tried the high pressure option but it hasn't worked yet.  Will try it again tonight, if I get the time I'll whip the bass end off and have a look.
Title: Re: Blown Reed?
Post by: Lester on January 16, 2008, 03:29:47 PM
Hi George, tried the high pressure option but it hasn't worked yet.  Will try it again tonight, if I get the time I'll whip the bass end off and have a look.
As any fule kno it is not possible to remove the bass end from a Tommy as it is glued to the bellows so you can only detach the treble end. Hope this is of some help  :P
Title: Re: Blown Reed?
Post by: Theo on January 16, 2008, 04:16:46 PM
Darren,

Is this a change from previous good behaviour?
Title: Re: Blown Reed?
Post by: Dazbo on January 16, 2008, 04:30:40 PM
Theo, yes it's a new change.  Three years fine service since I got it from Steve (yes it's more than three years now, Steve).  I first noticed it as a harder than usual pull at Monday's practice (bass itself being drowned out by other melodeons and drums).
Title: Re: Blown Reed?
Post by: oldclubII on January 16, 2008, 04:46:17 PM
Dislodged or damaged valve playing tricks on the reed?
Title: Re: Blown Reed?
Post by: Theo on January 16, 2008, 07:10:15 PM
Could be the valve on the push reed next to it which is not closing properly, or some foreign body that is stuck in  the reed.  Since A will be the pull reed, its on the 'inside' of the block and less easy to see.   If you are able to remove the reedblock (requires an extra long pozi screwdriver) look inside and see if valve beside teh A reed is lying flat.  Look at other valves for comparison, there is likely to be a little bit of curve on leather valves after a few years of playing.

If the reed plays in tune when it plays then its unlikely the reed is cracked.
Title: Re: Blown Reed?
Post by: Dazbo on January 18, 2008, 07:10:08 PM
Thanks Theo, I've just had the box apart and taken the bass reeds out.  It looks like the valve was bent almost U shaped away from its reed I poked it flat and and looked at the others and there was another valve similarly  shaped (although not as bad).  I've put it back together and had a quick play at morris volumes and it seems okay at the moment.

I noticed that some valves have springs to keep them flat but others don't.  Size of the valve doesn't seem to be correlated to the spring.  Are there some springs missing or is this normal?

Title: Re: Blown Reed?
Post by: Theo on January 18, 2008, 07:42:31 PM
I noticed that some valves have springs to keep them flat but others don't.  Size of the valve doesn't seem to be correlated to the spring.  Are there some springs missing or is this normal?

Most likely the springs have been added at sometime to correct valves that were not lying flat.

A common problem on very small boxes is that the outer valves can come into contact with the bellows.  If a valve catches on a fold then it can get bent double.
Title: Re: Blown Reed?
Post by: Steve_freereeder on January 19, 2008, 12:39:06 AM
I noticed that some valves have springs to keep them flat but others don't.  Size of the valve doesn't seem to be correlated to the spring.  Are there some springs missing or is this normal?
Most likely the springs have been added at sometime to correct valves that were not lying flat.
Interesting...
I had this instrument (from new) before I sold it to Darren several years ago. I never replaced any valve springs, so what is there now must be how it left the Castagnari factory.
SimplePortal 2.3.5 © 2008-2012, SimplePortal