Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Pete Dunk on May 15, 2020, 03:12:50 PM

Title: Plastic Valves
Post by: Pete Dunk on May 15, 2020, 03:12:50 PM
Does anyone here know what the specific type and thicknesses of 'film' or 'plastic' material are used to make accordion reed valves, and where they may be found? 'Vileda' is one term I have seen mentioned in relation to the yellow coloured film used on some chord reed plates but searching for it only turns up the well known brand of household cleaning products.
Title: Re: Plastic Valves
Post by: John MacKenzie (Cugiok) on May 15, 2020, 03:19:28 PM
Yes that's used to replace leather valves, usually bass I think.

SJ
Title: Re: Plastic Valves
Post by: Theo on May 15, 2020, 03:33:05 PM
You'll end up with a lot of work, time spent experimenting and so on if you make your own valves.  They are cheap to buy ready made.  Personally I don't like the vileda valves, they always seem rather floppy.   There are several types of composite valves available which have a leather layer with one or more plastic layers on top which give a good combination of the quietness of leather with the additional springiness of plastic. 
Title: Re: Plastic Valves
Post by: chris hall on May 18, 2020, 01:26:25 PM
where can we try these composite valves? cgm? sounds interesting
Title: Re: Plastic Valves
Post by: Theo on May 18, 2020, 01:32:06 PM
I get mine from Carini.  CGM doesn't list them.  This ebay seller (https://www.ebay.co.uk/itm/164206575418) is offering valves and the sets seem to include leather valves with plastic strengtheners.  You could contact them and see what else they have.
Title: Re: Plastic Valves
Post by: mselic on May 18, 2020, 01:40:12 PM
I’m curious - I’ve only ever used the plastic valves with the pre-punched holes. Is there any advantage or disadvantage to using the ones without holes? My thought was always that having the former meant there was more surface area for the valves to be glued onto the plate and were therefore more  desirable, but then again there are plenty of boxes without them...
Title: Re: Plastic Valves
Post by: Theo on May 18, 2020, 01:52:22 PM
Punched valves seem to be favoured by Hohner, virtually all Italian makers use unpunched. I’ve never semi punched leather valves.
Title: Re: Plastic Valves
Post by: Steve_freereeder on May 18, 2020, 02:17:17 PM
This ebay seller (https://www.ebay.co.uk/itm/164206575418) is offering valves and the sets seem to include leather valves with plastic strengtheners.  You could contact them and see what else they have.

The Ebay seller is OG Accordions, based in Bristol. Nice website and some good information. Judging by the 'Information' section I have a hunch that the business is run by a member(s) of this forum, or at least accesses this forum. Come on, own up...!

https://ogaccordions.com/
Title: Re: Plastic Valves
Post by: hickory-wind on May 18, 2020, 03:11:07 PM
I have done some research on valve design & manufacturing. One main advantage of perforated plastic valves is that the effective 'hinge' point for the valve is closer to the rivet allowing for more flexure and thus more air flow. I'm attaching photos of a valve test fixture with and without a valve and a second fixture that can accommodate a reedplate.

*edit* more flow means louder sounding to the ear outside of the instrument *edit*
Title: Re: Plastic Valves
Post by: mselic on May 18, 2020, 03:14:00 PM
Scott, you've created some wonderful tools and toys...
Title: Re: Plastic Valves
Post by: hickory-wind on May 18, 2020, 03:16:25 PM
Here is a picture of the flow and low pressure gauges I used on the test platform. The unit is in a locked laboratory at my university at the moment so I can't provide a photo of the entire rig with blower and gauges.

I am developing a flex tester that uses a high precision laser to measure the actual deflection of the valve under controlled air flow. Much more detail will follow when it is all complete.
Title: Re: Plastic Valves
Post by: chris hall on May 19, 2020, 02:42:23 PM
yes og accordions of bristol looks good for valves. alas pretty much out of stock of valves at moment according to website. also found this place that does composite and other valves in various sizes https://www.accordionary.com/en/product/2024/reed-valves-leather-synthetic.html
based in netherlands. anybody know website for carini and if they do small orders?
Title: Re: Plastic Valves
Post by: Theo on May 19, 2020, 02:45:08 PM
Carinidena.com is Carini’s website.  I think they do fairly small orders,  you would have to contact them and ask.  They have good English speakers.
Title: Re: Plastic Valves
Post by: Rog on May 19, 2020, 06:42:30 PM
Carini plastic valves are cheap. Their leather composite plastic valves for bass work out a bit more expensive than the straight leather valves (which are pretty cheap, it has to be said). But the booster springs are quite expensive and I reasoned the total cost of leather valves, if you include the faffing around fixing on booster springs, is greater and less convenient than their leather/plastic composites (these are like CGMs bass valves except the soft bit is leather whereas CGMs is a synthetic material). I do a lot of PAs and time becomes a valuable commodity ... so a few pence more on valves with booster spring in place is actually ok in the grand scheme of things.
Title: Re: Plastic Valves
Post by: Squeaky Pete on May 19, 2020, 10:01:01 PM
That's a very helpful run-through, Roger.
I'm finding fitting the booster springs a bit of a faff and I've been wondering about the comparative merits of pre-plasticked leathers.
Title: Re: Plastic Valves
Post by: Steve_freereeder on May 20, 2020, 01:49:39 AM
I'm finding fitting the booster springs a bit of a faff...

The booster springs can be a bit of a faff but I find you get used to it. It helps to put a tiny bit of downwards kink with tweezers or small round-nosed pliers on the last few millimetres where the 'dot' will go. This ensures the spring will press the valve flat.

Here's the sequence of gluing which I use:
1. Glue the valve in place.
2. Put a tiny bit of glue on the kinked portion of the spring and press into place on the valve. This just helps hold it in position while you get the dot ready.
3. Put a bit of glue on the dot and press into place over the spring.

Quote
and I've been wondering about the comparative merits of pre-plasticked leathers.
I find they are excellent and indeed save a lot of faffing about. Castagnari use them all the time now, no worries.
Title: Re: Plastic Valves
Post by: chris hall on May 21, 2020, 12:58:55 PM
Carini website of Italy looks great for valves and all kinds of other accordion goodies. huge choice. Here in the UK, OG accordions said very helpfully they will make up sets so i'll get a set from them first and see how that works out.
Title: Re: Plastic Valves
Post by: Theo on May 21, 2020, 03:02:00 PM
Good plan. Valves from Carini typically come in minimum quantity of 100 for each size,  so you need to know that the valves you order are suitable for your intended use.
SimplePortal 2.3.5 © 2008-2012, SimplePortal