Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Pat McInnis on November 13, 2020, 09:21:24 PM

Title: Bit my tongue off
Post by: Pat McInnis on November 13, 2020, 09:21:24 PM
I was hearing a strange sound from my E5(F#5) on my D row and noticed that it was really flat for some reason. I did some light sharpening but it kept getting flatter and was now more like D#??? Then I tested it again and 3/4 of the tongue came spitting out through the F# valve.  ::) Now I have a bunch of spares but nothing really obvious from CF,GC, C#C that seems right. I did just pick up that odd ball EB.
Question (finally): Do E/F# share the same plate in the key of E? There is no layout shown for anything with E and well, I'm clueless.

Thanks,
Pat
Title: Re: Bit my tongue off
Post by: Gonk on November 13, 2020, 09:26:21 PM
No, if you had an E row, the E5 and F#5 would be in the equivalent places of your D row's D5 and E5.

You could modify a F5/G5 reed, right?
Title: Re: Bit my tongue off
Post by: Tone Dumb Greg on November 13, 2020, 09:35:11 PM
They do on the B row, if I've worked it out right.
Title: Re: Bit my tongue off
Post by: Pat McInnis on November 13, 2020, 09:35:21 PM
No, if you had an E row, the E5 and F#5 would be in the equivalent places of your D row's D5 and E5.

You could modify a F5/G5 reed, right?

Is that my best option? G all the way to E seems far. I think it is the + reed at least.
Title: Re: Bit my tongue off
Post by: Pat McInnis on November 13, 2020, 09:43:27 PM
They do on the B row, if I've worked it out right.

Unfortunately I need the whole B row.  ;)
Title: Re: Bit my tongue off
Post by: Gonk on November 13, 2020, 09:45:35 PM
Is that my best option? G all the way to E seems far. I think it is the + reed at least.

Flip it around, too -- then it's just semitones.
G --> F#
F --> E
Title: Re: Bit my tongue off
Post by: Tone Dumb Greg on November 13, 2020, 09:52:17 PM
No, if you had an E row, the E5 and F#5 would be in the equivalent places of your D row's D5 and E5.
Quote
You could modify a F5/G5 reed, right?

Wouldn't that be F#5/G#5?
Even so, there was recent discussion which concluded that dropping reed pitches quite a long way by weighting with solder can be done successfully. Should work fine on a tone or two.
Title: Re: Bit my tongue off
Post by: Pat McInnis on November 14, 2020, 03:22:23 PM
Alternately I could look at buying a single E/F#-5 from someone; maybe Charlie Marshall will have a single? I could actually use a couple of other random treble reed sets and some single bass/chords to make up a decent BC as well.

Anyone holding? :-X
Title: Re: Bit my tongue off
Post by: Squeaky Pete on November 14, 2020, 04:31:44 PM
I'll have a rummage.
Title: Re: Bit my tongue off
Post by: Pat McInnis on November 14, 2020, 04:40:53 PM
I'll have a rummage.

You're the man Pete!!

I'll see if I can figure out what else I need.
Title: Re: Bit my tongue off
Post by: Tone Dumb Greg on November 14, 2020, 05:16:17 PM
...maybe Charlie Marshall will have a single?...

If you still need odds and ends Charlie is quite happy to sell single reeds and small lots. I have bought Hohner and Cagnoni off him without any difficulties..
Title: Re: Bit my tongue off
Post by: Squeaky Pete on November 14, 2020, 06:49:51 PM
I'm just about to strip a club IV so there should be 3 of everything, or near enough to bodge/file/alter.
You're welcome to a little of my plunder.
Title: Re: Bit my tongue off
Post by: Pat McInnis on November 14, 2020, 08:27:19 PM
...maybe Charlie Marshall will have a single?...

If you still need odds and ends Charlie is quite happy to sell single reeds and small lots. I have bought Hohner and Cagnoni off him without any difficulties..

It's a shame, I placed a big order with him just a week ago. Could have piggybacked shipping.
Title: Re: Bit my tongue off
Post by: Squeaky Pete on November 14, 2020, 09:02:29 PM
I have a E5/F5 aluminium reed. It's a bit sharp anyway so should easily make F#.
The plate is 39mm long. Will that fit?
Title: Re: Bit my tongue off
Post by: Pat McInnis on November 15, 2020, 01:10:31 AM
I have a E5/F5 aluminium reed. It's a bit sharp anyway so should easily make F#.
The plate is 39mm long. Will that fit?

Message sent and did I mention how awesome this community is?
SimplePortal 2.3.5 © 2008-2012, SimplePortal