Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Winston Smith on December 06, 2020, 02:38:12 PM

Title: Dix?
Post by: Winston Smith on December 06, 2020, 02:38:12 PM
I've just scrapped a knackered German PA and I was led to believe (quite a while ago) that Dix reeds had the circle stamp as their mark. My question is, "Can anyone confirm that these are Dix reeds?"
Title: Re: Dix?
Post by: Dave Praties on December 06, 2020, 03:01:16 PM
Hello Winston, I am no expert on reed identification, but I recently similarly scrapped a PA, (every little helps), and it too had reeds marked with an “0”. It was a cheap Klingenthal apparition, which would almost certainly not have had Dix reeds, which I believe were quite up-market.
Dave
Title: Re: Dix?
Post by: Nigel.H on December 06, 2020, 03:07:00 PM
I would say - yes.....the impress stamp is identical to that on a wood finish older Box I bought to have a look at Dix reeds on the strength of the mark.

They were typical machine made riveted reeds.

When the Bachenbulach arrived, it too has Dix reeds, but the rivets have the triple face finish of typical handmade reeds.  They are longer bladed and ground along the length of the reed as opposed to across it like Hohner ones ?  You can just about see the lengthways 'grind' in the reeds in the image attached.  The Box is a 1930's, Swiss Made.

I think they probably had a range available at cost to builders as they were effectively suppliers of reeds not boxes?   There is a TM associated ( it seems ) with their mid period, quality reeds.....I have seen it mentioned before.....Langstahl ?? or some such ? 

Interestingly.....in the hands of an amateur......when working on the reeds, the Hohner ones 'move about' in the tune a bit but the steel is quite a bit softer to fettle.  Dix ones move more efficiently but are marginally harder to work.  Italian hand mades from the same period are really hard, arguably very high quality ( or just hard! ) steel.  Harder than current hand made Voci Armoniche ones.


Title: Re: Dix?
Post by: Nigel.H on December 06, 2020, 03:32:58 PM
My old Box....I have never really looked at it properly and unlike the later Dix (?) circle stamped reeds, these are clearly ground side to side, machine made, dry fitted.  It is probably 1900's/1910's.....not pretty and no branding.

It supports the idea of Dix design improvement associated with the long grinding of the reeds which I have seen mentioned elsewhere on the forum ?  When long ground the plates are longer, if not noticeably narrower for the same 'voice' in a typical reed plate.
Title: Re: Dix?
Post by: diatonix on December 06, 2020, 08:21:10 PM
Virtually all reeds from East Germany, both from before and after the war, were marked with a circle, no matter by whom they were made. Dix was just one among many others. A bit like the slash on Italian reeds.
Title: Re: Dix?
Post by: Winston Smith on December 06, 2020, 08:31:14 PM
"Virtually all reeds from East Germany, both from before and after the war, were marked with a circle, no matter by whom they were made. Dix was just one among many others. A bit like the slash on Italian reeds."

Well! I thought that I'd read something similar once before, and that's what prompted me to ask. Thanks for that contribution, diatonix. And thanks also to the others, even though I'm no further forward, lol.

(Actually, the big bass reeds on this thing have the corner slash.)
Title: Re: Dix?
Post by: Nigel.H on December 06, 2020, 08:51:25 PM
One or two of the reeds in the handmade set have the corner slash, but are obviously made identically.

"Langsschliff" was that Dix term for the long ground reeds (image from a listing ).

This suggests the 'O' mark was - for a time - a Trademark (Google Chrome Translate helps ) 

http://balbuluz.blogspot.com/2011/11/stimmplatten-der-gebr-dix-gera.html?m=1
Title: Re: Dix?
Post by: Winston Smith on December 07, 2020, 12:46:03 AM
I'll check the rivets and the grinding in the morning, but I did notice that the surface of the reeds looked "different" in some way. Who knows?
Title: Re: Dix?
Post by: Peadar on December 08, 2020, 12:13:39 AM
I was under the impression that the Dienst Internationals were fitted with Dix reeds. All of mine (D's , A&D and C/C#) have circle marked reeds.
Title: Re: Dix?
Post by: Winston Smith on December 08, 2020, 12:21:49 AM
I did have a look this morning. The rivets are not hand hammered, but the actual reeds are definitely ground along their length. Under a glass, the marks are obvious.
SimplePortal 2.3.5 © 2008-2012, SimplePortal