Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Gav Wood on December 24, 2020, 09:15:10 AM

Title: Holey gussets
Post by: Gav Wood on December 24, 2020, 09:15:10 AM
On my second consecutive project with old bellows where the bellows gusset leather lets air through. This is not the joins but the leather itself.

Last one was a set of lilliput bellows, took them back to card strips eventually and regusseted before new cloth and tape. The card and corners were the only bits salvaged. The end job is now airtight, the gussets you could breathe through before.

This one is a circa 1960 paolo soprani, built a lot better but the large gussets also leak air through the leather. You can suck air through the gussets i have removed so far, compared to the leather i used for the replacement lilliput gussets, there is a lot of air comes through them.

Does anyone treat the gussets to keep them airtight, and is this normal?  I am coming to the conclusion i will need to replace all the gussets but if there is another way, please let me know.

I had a white leather coat for £3 off ebay, the daughter is getting it as a christmas present as I was told it was too good to cut up for gussets, looks new. I am on the lookout for another one.
Title: Re: Holey gussets
Post by: folkloristmark on December 24, 2020, 11:00:47 AM
Gusset material is not 100% airtight when new The original old lint on hohers for example but as they decay they do leak. In my opinion if they just leak then repair with triangles of very very thin leather or better lint with PVA rather than cut them out. this should be invisible glued from the inside. With bad bellow a whole strip from one end to another but not too thick as to change the bellows compression.The hardest thing is keeping the glue off every thing else and the covering the wet areas with kitchen paper or foils so you can compress the bellows to dry with out the folds all glueing together. I use a rod and pins to keep the bellows open while working cover the work from end to end and then compress with weights on closed bellows till nearly dry but open then so any glue errors are more easily rectified. If the gussets just leak without holes you might get away with just latex PVa water mix with out the material just cover with grease paper from the inside it will still but can be reomved.This is all very messy but is much easier then removing all the gussets and corners .I have had good success in the past but try to avoid boxes with such bellows now. Cosmetically it should all stay on the inside its really your call on which corners you replace
good luck
Title: Re: Holey gussets
Post by: Gav Wood on December 24, 2020, 11:40:34 AM
Thanks Mark, thought about latex, but remember a thread recently where someone said it does not last long. Friend of mine uses latex to line his northumbrian pipes bag, but has to be redone every few years.


This project is cutting down bellows from continental chromatic size to melodeon, was going to keep 2 out of 4 corners in tact and transfer the gussets from the binned corners, reinforcing does not seem sensible if i am already half way to replacing anyway.

Might have a go at painting a couple with different glues and see how they react.
Title: Re: Holey gussets
Post by: Gav Wood on December 24, 2020, 12:29:16 PM
Experiment in progress.
Title: Re: Holey gussets
Post by: JNM SY on December 24, 2020, 07:59:09 PM
Imagine if there was some kind of water-proof spray on sealer, you could do a whole bellows super quick. Im sure there is one out there somewhere.
Just a thought - Seasons Greetings,  John
Title: Re: Holey gussets
Post by: Gav Wood on December 24, 2020, 08:20:27 PM
Yes, that is what the plasticote is supposed to do, however early results are this is not viable, all the others are pliable, the spray on plastcote is rigid. At present, 1,2,4 and 5 are completely sealed and varying degrees of flexible, the others not. will scrumble them about after xmas then have another go.
Title: Re: Holey gussets
Post by: folkloristmark on December 25, 2020, 07:59:49 AM
I have pva ones that have lasted 10 years but they may not have been as extreme as others and the original gussets were still in place.They have not be payed as regular either.Replacement bellows is always better if a keeper.
Title: Re: Holey gussets
Post by: boscaceol on February 19, 2023, 09:19:36 AM
Hi Mark, do you have any photos of the gusset repair?  I am going to have to repair all of them on this box, it’s an oddball size bellows so I can’t get a second hand replacement.  Where could I possibly get a suitable lint material to use for the gussets, this seems like a better material than leather.
John
Title: Re: Holey gussets
Post by: Winston Smith on February 19, 2023, 09:42:16 AM
I've got to say that there's more to life than bellows corners! Even being the cheapskate that I am, I think that you're all (possibly a colloquialism that could be misunderstood) 'fond of a treat', and that a set of second hand or even new bellows would be my choice rather than all that clart-on.
Title: Re: Holey gussets
Post by: boscaceol on February 19, 2023, 12:27:08 PM
Of course, and that’s what I would normally do!
Title: Re: Holey gussets
Post by: Squeaky Pete on February 19, 2023, 12:47:55 PM
I painted weak water soluble PVA on some leaky gussets and virtually eliminated the leaks.
The Melodeon is still very playable, better than I ever thought possible.
Title: Re: Holey gussets
Post by: Kimric Smythe on February 25, 2023, 06:07:02 PM
I would not bother reusing gussets if you are putting in all that effort to modify bellows. Places that sell parts for player pianos and organ parts suppliers often have leather for just this purpose.
SimplePortal 2.3.5 © 2008-2012, SimplePortal