Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Mark Leue on December 29, 2020, 10:29:57 PM

Title: Hohner Preswood: imagining what they looked like new.
Post by: Mark Leue on December 29, 2020, 10:29:57 PM
I'm sure others have tried this, but the "blond" "Presswoods" seem to have lost contrast between the recessed surface and the flush one over the years. you can see some of that on areas that didn't get much light where the pattern stands out a lot more.
It's quite easy to bring back a color contrast with some acrylic paint. Here's one I fooled around with today, that I think looks nice.
Before:

(http://)
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: Mark Leue on December 29, 2020, 10:31:54 PM
And doctored up, after I took this I lightened up a few areas and then a light coat of shellac to seal it in.

(http://)
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: Squeaky Pete on December 29, 2020, 10:55:36 PM
That looks really good.
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: Mark Leue on December 29, 2020, 11:35:07 PM
That looks really good.

I think it probably is what Hohner had in mind more or less.   Here's the keyboard.  before

(http://)
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: Mark Leue on December 29, 2020, 11:37:26 PM
and after.

(http://)
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: Peadar on December 30, 2020, 12:35:21 AM
Hi Mark,
That looks good. Nice piece of re-finishing. :D
P
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: Mark Leue on December 30, 2020, 01:53:07 AM
I wonder what it would look like in red or something bit more... loud. As if melodeons were not loud enough to start with.
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: hickory-wind on December 30, 2020, 03:20:50 AM
You don't need to wonder. I affectionately call these the Wes Anderson models. I converted this from CC# to C#D.

https://youtu.be/4nI5uZYuS4E (https://youtu.be/4nI5uZYuS4E)

Scott
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: hickory-wind on December 30, 2020, 03:31:33 AM
I like what you did with the pressedwood. A definite improvement.

I personally love the precursor to the pressedwood that I call 'black & blond'. It it a bit more bold than your nice subtle hue.

This one is an EA conversion that I am added a third set of high reeds to get a full time MMH configuration. It will have its own thread when I'm done.

Scott
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: Graham Spencer on December 30, 2020, 07:03:05 AM
And doctored up, after I took this I lightened up a few areas and then a light coat of shellac to seal it in.


I like that.  Normally I'm not keen on over-restoring (of anything!) and getting an old object to look "as new", as the knocks, dings and wear are pert of the object's life-story, but that looks nicely restrained and "well looked after" rather than "straight out of the factory".

Graham
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: Broadland Boy on December 30, 2020, 01:22:08 PM
I have long believed that these are the true 'Pokerwork's the pressed, scorched decoration being done with a similar apparatus to that used for scorching details and decorations onto boxes to contain all sorts of products from kippers to spuds. The impress usually being cut into zinc sheet heated electrically or by gas - can be seen in action in this video, skip to 7 mins if in a hurry
https://www.youtube.com/watch?v=_mKSKZau9qs

This mimicing the labour intensive hand pokerwork using a heated wire or bit.

Degree of heating could be varied, subsequently could be black and gold lacquered for the Goldbrand, those I've seen showing no sign of much heat when being impressed - is this the experience of restorers or those who have stripped them for repainting etc ?
Title: Re: Hohner Preswood: imagining what they looked like new.
Post by: Steve C. on December 30, 2020, 01:22:56 PM
Gents, do you stain it dark, then sand or ? off the high points?
Very nice.
SimplePortal 2.3.5 © 2008-2012, SimplePortal