Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Vallenato831 on January 05, 2021, 05:56:04 PM

Title: Cracked Bellow Frame
Post by: Vallenato831 on January 05, 2021, 05:56:04 PM
Cracked wooden bellow frame at the pin hole site, glue and give it a go?  Or replace the frame? 
Title: Re: Cracked Bellow Frame
Post by: Theo on January 05, 2021, 06:52:35 PM
Hard to know without a picture, but it’s not any easy site to repair.  If split along the grain it might be reinforced by one or two carefully fitted wood screws. 
Title: Re: Cracked Bellow Frame
Post by: Vallenato831 on January 05, 2021, 07:04:38 PM
Hard to know without a picture, but it’s not any easy site to repair.  If split along the grain it might be reinforced by one or two carefully fitted wood screws.

Photos attached.  Not sure what the previous owner did, but looks like he totally screwed up when inserting the pins.  >:(  Fortunately, it is still air tight.  But surely going to be a problem sooner or later. 

Title: Re: Cracked Bellow Frame
Post by: folkloristmark on January 05, 2021, 07:59:49 PM
I would glue clamp and fill that, then relocate the actual pin to one side and drill new hole.Need to do both opersites if the eye line needs to be kept thats a cosmetic visual thing.
Title: Re: Cracked Bellow Frame
Post by: rees on January 05, 2021, 08:01:14 PM
I would cut out and replace that section of the frame.
Title: Re: Cracked Bellow Frame
Post by: chris hall on January 05, 2021, 08:01:52 PM
maybe bellows pin was hammered in without frame lined up. Also I encountered same result recently from instrument being dropped. I fixed with titebond wood glue and small clamp. could also be an indication that new frame seal has been used that is deeper than original. Id just try wood glue and clamp and try and get pin in original hole. could reinforce frame along inside edge if necessary again with wood glue and thin wood (coffee stirrer or lolly stick should work). Id only consider new frame as last resort. superglue in original hole after repair might also help pin sit tight. If other 3 pins fit good you should be ok. 
Title: Re: Cracked Bellow Frame
Post by: chris hall on January 05, 2021, 08:17:39 PM
I would cut out and replace that section of the frame.

even better. assume you would angle the replacement piece at 45 degrees so it pulls into place? but maybe with good wood glue a straight fit would be ok?
Title: Re: Cracked Bellow Frame
Post by: John MacKenzie (Cugiok) on January 05, 2021, 08:21:53 PM
I  would drill through both holes, then pare down  a piece of wood to fit the holes, and insert the wood with superglue, which will osmose along the crack. Once dried, tidy up and sand, then with the bellows frame in the box, mark the spot for a new hole, using the existing hole in the carcase of the box as a guide, take frame out again, and drill new hole, of the appropriate size.
Make sure the frame is tight, when marking the new hole position. I usually remove the old gasket before I mark the position, then the new gasket will be compressed properly, when refitted.
SJ
Title: Re: Cracked Bellow Frame
Post by: diatonix on January 05, 2021, 08:31:51 PM
I would cut out and replace that section of the frame.
Absolutely!
Title: Re: Cracked Bellow Frame
Post by: Theo on January 05, 2021, 09:20:26 PM
I would cut out and replace that section of the frame.
Absolutely!

Agreed.  All the other suggestions will lead to this.  Best do a proper job first time.
Title: Re: Cracked Bellow Frame
Post by: Vallenato831 on January 06, 2021, 04:59:22 PM
maybe bellows pin was hammered in without frame lined up. Also I encountered same result recently from instrument being dropped. I fixed with titebond wood glue and small clamp. could also be an indication that new frame seal has been used that is deeper than original. Id just try wood glue and clamp and try and get pin in original hole. could reinforce frame along inside edge if necessary again with wood glue and thin wood (coffee stirrer or lolly stick should work). Id only consider new frame as last resort. superglue in original hole after repair might also help pin sit tight. If other 3 pins fit good you should be ok.

Yeah, those are the front 2 holes on the treble side.   The back 2 holes are perfect.  Definitely human error when inserting the pins.  I may go the wood glue route first. 

I'd love to do it the right way, cutting out that piece and gluing a new one in, but my carpentry skills are 0 to none.  Will do more harm than good.  Probably send off to an experienced technician to fix.  Appreciate all the feedback, extremely helpful.  Thanks all. 
SimplePortal 2.3.5 © 2008-2012, SimplePortal