Melodeon.net Forums

Discussions => General Discussion => Topic started by: Organettisto on October 11, 2009, 06:57:55 AM

Title: Microphone Placement for Recording
Post by: Organettisto on October 11, 2009, 06:57:55 AM
Hi, I was interested in peoples' experience with micing melodeons.  I'm specifically interested in the best mic placement for micing Italian organettos, which usually have 3 reeds per note and are rather loud and full sounding.   I'm using a stereo pair of condenser mics (Audio technica 4051a) and I'm trying to figure out the best distance from the instrument and also how to configure them (ie. xy pattern, or direct one mic at each side of the box).   In the coming weeks I plan to do more tests and see what I like best.  Should the mics be close up or farther back in the room?  My initial tests with the mics pretty close up in an xy pattern sounded a little muddy.    In the meantime I'm interested in hearing any other peoples' experiences.
Thanks,
David
Title: Re: Microphone Placement for Recording
Post by: Steve_freereeder on October 11, 2009, 09:39:58 AM
For both recording and gig use, I use a pair of AKG C1000 condenser microphones mounted on stands. I have them set up so that both mics are about 30 cm apart, their axes parallel and approximately horizontal, pointed straight at the melodeon at about mid-height. The mic heads are about 40 - 60 cm from the melodeon. When recording in stereo, this gives a sufficient L-R separation (but not too much), so that the melodeon sounds pretty much as it would do to an audience member located a few metres away. The narrow separation of the mics also means that I don't get any noticeable fading and swelling of the volume as a result of bellows movement.

Hope this helps, but ultimately you will have to experiment to see which works best for your particular combination of equipment and instruments.
Title: Re: Microphone Placement for Recording
Post by: IanD on October 11, 2009, 03:01:26 PM
Hi, I was interested in peoples' experience with micing melodeons.  I'm specifically interested in the best mic placement for micing Italian organettos, which usually have 3 reeds per note and are rather loud and full sounding.   I'm using a stereo pair of condenser mics (Audio technica 4051a) and I'm trying to figure out the best distance from the instrument and also how to configure them (ie. xy pattern, or direct one mic at each side of the box).   In the coming weeks I plan to do more tests and see what I like best.  Should the mics be close up or farther back in the room?  My initial tests with the mics pretty close up in an xy pattern sounded a little muddy.    In the meantime I'm interested in hearing any other peoples' experiences.
Thanks,
David

Depends very much whether you mean for recording or playing live, the requirements are very different.

For recording (as set up by a very experienced recording engineer) I used two large-diaphragm cardioid condenser mics, the treble one about 50cm away from the grille and slightly above it, the bass end one about 50cm away from and below the typical bass end position -- so both mics point towards each other, but from opposite ends of the box.

This gives even pickup with minimum bleed between the two channels, important if playing as part of a band -- you often want to turn up the treble end in the mix and leave the bass end where it is. The sound may be a little bit brighter then mics positioned in front of the box but this is easily corrected. The relatively close distance means you don't get too much reverb from the room.

For recording just a solo box you could have the mics further away if you want more room sound. Or you could use a crossed cardioid pair placed in front of the box and about 60cm away, which will give a less bright sound but more bleed between the two ends -- much closer than this and you lose treble giving a dull sound. I wouldn't recommend a relatively closely spaced parallel pair of mics (as Steve suggested) because both mics pick up both ends with different delays causing comb effect interference, you can then get a hollow sound which changes with box position and can't easily be removed by equalisation.

For playing live through a PA either of these setups would probably be too prone to feedback, especially from the bass end and if using monitors (not an issue in the studio with headphones). In this case I'd recommend a hypercardioid mic on a stand for the treble end placed about 30cm away from the grille, positioned to minimise monitor feedback (either in front or to the side of the box depending where the monitors are).

This solution isn't so good for the bass end, if it's close enough to minimise feedback then the volume varies all over the place as the bass end moves around -- though for players who don't use the bass end much this might not matter so much. I've found the best solution is a high-quality clip-on mic (fastened to the box) on a miniature gooseneck, positioned so it points towards the bass end sound holes from 15-20cm away (depends on length of gooseneck) -- I use a Beyerdynamic Opus 82 set (includes a preamp, needs phantom power) clipped to the bottom of the bass end strap:

http://www.dv247.com/microphones/beyerdynamic-opus-82-set--58496

If you try this I strongly suggest the (optional) windscreen, otherwise a use of the air button while playing hard can cause a rumble in the mic as air is blown towards it -- this caused some time to track down since it doesn't happen when playing more quietly:

http://www.dv247.com/microphones/beyerdynamic-ws-97-windscreen-for-opus-and-dt-series-charcoal-grey--59756

Hope this helps

Ian
Title: Re: Microphone Placement for Recording
Post by: Steve_freereeder on October 11, 2009, 04:09:31 PM
I wouldn't recommend a relatively closely spaced parallel pair of mics (as Steve suggested) because both mics pick up both ends with different delays causing comb effect interference, you can then get a hollow sound which changes with box position and can't easily be removed by equalisation.
Ian, could you explain this a bit more please? I am very much a novice in this field and don't know what you mean by 'comb effect interference'. The results I get from my set-up sound OK to me, but perhaps I am just not critical enough. What do you mean by a 'hollow sound'?

Quote
For playing live through a PA either of these setups would probably be too prone to feedback,
My set-up as described in my earlier post actually work OK in the band I play in, and there is rarely any feedback problem. The sound quality I get is better than I previously had with AKG clip-on mics; I no longer get any air-button whoosh and RH button rattling is hardly picked up at all.

Interesting thread. I'll be grateful for advice and feedback ('howls' of derision?) too.
Title: Re: Microphone Placement for Recording
Post by: LJC on October 11, 2009, 05:07:27 PM
I've often used an XY pair of mics positioned about 30cm above the top of the box and around 1-2m away pointing down. You'll always get some bass volume changes with the movement but you can use a multiband compressor on the lower frequencies to even them out without squashing and disrupting the higher ones.

The key is to use a second person to walk about your recording room whilst you play and then position mics where it sounds good in the room - if you capture a good basic sound then there is a lot less work to do later on trying to fix things. Record, listen back, adjust, until your happy.

I've got some very convincing recordings using just one stereo mic. Sound on Sound magazine have a good online database of back issues if you register (free!). A quick google gave me http://www.soundonsound.com/sos/1997_articles/feb97/stereomiking.html (http://www.soundonsound.com/sos/1997_articles/feb97/stereomiking.html) which looks about right (It's old, but basic mic technique hasn't really changed). I used a Royer stereo mic - they are about £3500 to buy, but many places will either let you try for a week so you can return it if you like or hire them out. It's worth spending £100 or so on superb mic hire than more money on a lesser quality mic.

However - If your recording with cheap thin cables or in a noisy room you will only get a sound as good as your weakest link. Nothing wrong with C1000's though, perfectly acceptable and I've used them on commercial recordings.

With any acoustic instrument I always think it is best to give it plenty of air so that the sound can develop before it reaches the microphone. Anything close up will sound odd as its the equivalent of listening to the box with your ear to the grille.
Title: Re: Microphone Placement for Recording
Post by: IanD on October 11, 2009, 05:12:30 PM
I wouldn't recommend a relatively closely spaced parallel pair of mics (as Steve suggested) because both mics pick up both ends with different delays causing comb effect interference, you can then get a hollow sound which changes with box position and can't easily be removed by equalisation.
Ian, could you explain this a bit more please? I am very much a novice in this field and don't know what you mean by 'comb effect interference'. The results I get from my set-up sound OK to me, but perhaps I am just not critical enough. What do you mean by a 'hollow sound'?

Quote
For playing live through a PA either of these setups would probably be too prone to feedback,
My set-up as described in my earlier post actually work OK in the band I play in, and there is rarely any feedback problem. The sound quality I get is better than I previously had with AKG clip-on mics; I no longer get any air-button whoosh and RH button rattling is hardly picked up at all.

Interesting thread. I'll be grateful for advice and feedback ('howls' of derision?) too.


If you use two relatively closely spaced mics both of which pick up close to equal volume from a sound source which isn't midway between them, then at some frequencies the signals from the mics add (in phase) and at some frequencies they subtract (out of phase) -- this gives bumps and dips in the frequency response, which are worse the closer to equal volume the two mics pick up.

http://www.mcsquared.com/2mics.htm

For example, say the difference in the path lengths to the mics is a foot, which is about 1 wavelength at 1KHz. At frequencies which are multiples if 1kHz (low, 1kHz, 2kHz, 3kHz...) the signals add, at frequencies where the path length difference is half a wavelength (0.5kHz, 1.5kHz, 2.5kHz...) the signals subtract. The ear usually picks this up as a kind of "hollow phasey" sound, I can't really describe it any better than that. It's called "comb effect" because that's what the frequency response looks like if you plot it out, a series or regular peaks and troughs.

It can be quite obvious sometimes, depending on how closely you're listening to the sound -- as the player it's not so obvious because you also hear the sound direct, but it can be quite obvious through a PA or when recording. If you want to see how it sounds, wear some headphones with good isolation, set both mics to the same level (and panned to centre), and play a note on the treble end while moving sideways in front of the mics. The "true" sound is when you're exactly between the two mics; as you move sideways you'll hear the tone change as the response dips move up and down in frequency.

The effect is especially obvious with reed instruments because they have a lot of high-pitched harmonics, and most so with single-reed instruments -- concertina is probably worse than anything else, but (assuming you're listening carefully) it can quite spoil the sound of melodeons as well.

A crossed pair doesn't suffer from this effect because the mics are coincident, and neither do two widely spaced mics (one pointed at each end) because they each pick up the sound from one end.

Ian
Title: Re: Microphone Placement for Recording
Post by: IanD on October 11, 2009, 05:23:24 PM
I've often used an XY pair of mics positioned about 30cm above the top of the box and around 1-2m away pointing down. You'll always get some bass volume changes with the movement but you can use a multiband compressor on the lower frequencies to even them out without squashing and disrupting the higher ones.

The key is to use a second person to walk about your recording room whilst you play and then position mics where it sounds good in the room - if you capture a good basic sound then there is a lot less work to do later on trying to fix things. Record, listen back, adjust, until your happy.

I've got some very convincing recordings using just one stereo mic. Sound on Sound magazine have a good online database of back issues if you register (free!). A quick google gave me http://www.soundonsound.com/sos/1997_articles/feb97/stereomiking.html (http://www.soundonsound.com/sos/1997_articles/feb97/stereomiking.html) which looks about right (It's old, but basic mic technique hasn't really changed). I used a Royer stereo mic - they are about £3500 to buy, but many places will either let you try for a week so you can return it if you like or hire them out. It's worth spending £100 or so on superb mic hire than more money on a lesser quality mic.

However - If your recording with cheap thin cables or in a noisy room you will only get a sound as good as your weakest link. Nothing wrong with C1000's though, perfectly acceptable and I've used them on commercial recordings.

With any acoustic instrument I always think it is best to give it plenty of air so that the sound can develop before it reaches the microphone. Anything close up will sound odd as its the equivalent of listening to the box with your ear to the grille.


A crossed XY pair spaced well back is one good technique, whether this is appropriate depends on how "dry" you want the recording to be and how much bleed between the two channels is acceptable. In a good-sounding room (with the amount and quality of reverb you want) this can work very well to give a "natural" sound, assuming that you do want the sound of the box "as is" -- I agree that micing too close gives an unnatural sound, but usually by two or three feet away you're in the far-field for sound (rule-of-thumb -- for accurate far-field sound you want to be a distance away which is twice the size of the sound-radiating part of the instrument).

Many melodeons in particular sound better with some added EQ, especially on the bass end to remove any honky or buzzy sounds, and you don't want this EQ to apply to the treble end. In this case a mic technique which gives good isolation between the two ends is preferable, and a crossed pair is not so good for this.

Ian
Title: Re: Microphone Placement for Recording
Post by: Steve_freereeder on October 11, 2009, 07:36:11 PM
Ian and LJC,

Many thanks for your responses. You have given me quite a bit to think about and try out. 

Steve
Title: Re: Microphone Placement for Recording
Post by: Organettisto on October 11, 2009, 11:04:12 PM
Thanks for all the responses guys.  I'm probably going to go with something like the crossed pair a few feet away to go for the "true" sound.  I'm limited by the mics I own and the fact that I can only use one microphone stand (with a T adapter to put two mics on the end).  I'll be making these recordings in the field in Southern Italy in remote areas.  My entire recording set up fits in a backpack which includes a modified mic stand that I shortened substantially with a hack saw ;D
Title: Re: Microphone Placement for Recording
Post by: rees on October 11, 2009, 11:15:09 PM
Thanks for all the responses guys.  I'm probably going to go with something like the crossed pair a few feet away to go for the "true" sound.  I'm limited by the mics I own and the fact that I can only use one microphone stand (with a T adapter to put two mics on the end).  I'll be making these recordings in the field in Southern Italy in remote areas.  My entire recording set up fits in a backpack which includes a modified mic stand that I shortened substantially with a hack saw ;D


Excellent project. Calabria? Basilicata? I look forward to hearing the fruits of your field trip. Good luck in your travels.
Title: Re: Microphone Placement for Recording
Post by: Organettisto on October 12, 2009, 02:59:52 AM
This particular trip I'm going mainly to record zampognas, but since a lot of the guys who play the pipes also play the organetto, I'm hoping to get some recordings of that as well.  I'll be in South Eastern Campania, very close to the dividing line with Basilicata visiting my relatives and recording the local folk musicians in their little town up in the foothills of the Apennines.  Then I'll be heading to South Eastern Lazio in the Amatrice region to record pipers and hopefully organetto guys who play saltarellas (type of italian dance not the brand of box!).  I'll also be recording people in Rome proper before flying back to the states.   This is part of a larger project to gather a comprehensive collection of Southern Italian folk music over the next few years.  I started this project in summer 2008 and this is my second time back for this purpose.  It's going to be crazy! I'll probably need some luck!
Title: Re: Microphone Placement for Recording
Post by: LJC on October 12, 2009, 07:38:49 AM
If your doing it outside then the big foam wind shields are a must - there is nothing worse than getting a great take with a load of whooshing over it!
Title: Re: Microphone Placement for Recording
Post by: Chris Brimley on October 12, 2009, 10:01:52 AM

Quote
For both recording and gig use, I use a pair of AKG C1000 condenser microphones mounted on stands. I have them set up so that both mics are about 30 cm apart, their axes parallel and approximately horizontal, pointed straight at the melodeon at about mid-height. The mic heads are about 40 - 60 cm from the melodeon. When recording in stereo, this gives a sufficient L-R separation (but not too much), so that the melodeon sounds pretty much as it would do to an audience member located a few metres away. The narrow separation of the mics also means that I don't get any noticeable fading and swelling of the volume as a result of bellows movement.

Steve, I use a very similar arrangement for live playing with my two Samson Q1 condenser mikes, except that I try to align the axes so that they are pointing directly away from the monitor, and perhaps I have both mikes slightly closer to the box, but also slightly further apart.  It seems to me that it is good to get separation between the mikes, but the distance will also depend on whether one's playing style uses lots of bellows (and body) movement, because it's desirable to keep the LH side response even, and therefore keep the sound source within the 'cone'.   I think of it like this:  a condenser mike has a narrow 'cone' of roughly even response, and outside that cone, response drops off quickly.  So I am trying to keep the RH side safely within the cone of the mike facing it, and the LH side similarly with the other mike, but such that the centre of the cone is at about the average position of the bellows.  This should give an even response, without noticeable interference between the signals from each mike. 

I wasn't aware of (and have never noticed) the comb effect interference issue IanD describes, but I do see that it can be a problem, (more so with cardiods?) - however if you keep the signals as separate as you can by spacing as I have tried to do, I would have thought that it shoudn't be too much of an issue anyway?  I will also in future try to angle each mike slightly away from the other, which should enhance the separation between the channels still further, without causing too many feedback problems.

However, it seems to me that by far the most important practical issue on stage is that of feedback.  With the arrangement I use, it really minimises this problem - I control the sound desk myself in the band, so I need to be able to hear everybody through the monitor as well as I can.  I have the wedge monitor pretty close to me therefore, about 1-1.5m away from the rear of my mikes.  But I usually find I could easily turn myself up far higher than the other acoustic instruments (particularly flute or violin), without any feedback.

Close miking systems are OK, but they don't seem to give this 'narrow response cone' effect, and I have to say (hopefully not too controversially!), they just do not seem to sound as natural as floor-mounted mikes.  I guess that it is because with a box the sound sources are all separated spatially, so a close mike system has to compromise on the frequency response from each reed - some will be closer than others, and will therefore inevitably sound more 'bassy'.  If this is corrected by equalisation, the other reeds will sound more tinny, won't they?

Another interesting question from this thread for the sound experts - if you have a mike pointing at the bass end from the side, is it possible that the speed of bellows movement is enough to create a noticeable Doppler effect?

Title: Re: Microphone Placement for Recording
Post by: Organettisto on October 12, 2009, 04:01:03 PM
LJC - I have rycote mini windjammers for my condenser mics.  They aren't amazing but they are better than nothing and work in low wind conditions.  Really to properly deal with any kind of moderate wind i would need baby-ball blimps around the mics and those cost a lot of money.  I just have to be careful when I record.


Now I'm off to las vegas for the italian folk music confrence.  Ill be giving a workshop demo on the zampogna and organetto and playing live music for some fold dance groups!

David
Title: Re: Microphone Placement for Recording
Post by: IanD on October 12, 2009, 10:55:31 PM

Quote
For both recording and gig use, I use a pair of AKG C1000 condenser microphones mounted on stands. I have them set up so that both mics are about 30 cm apart, their axes parallel and approximately horizontal, pointed straight at the melodeon at about mid-height. The mic heads are about 40 - 60 cm from the melodeon. When recording in stereo, this gives a sufficient L-R separation (but not too much), so that the melodeon sounds pretty much as it would do to an audience member located a few metres away. The narrow separation of the mics also means that I don't get any noticeable fading and swelling of the volume as a result of bellows movement.

Steve, I use a very similar arrangement for live playing with my two Samson Q1 condenser mikes, except that I try to align the axes so that they are pointing directly away from the monitor, and perhaps I have both mikes slightly closer to the box, but also slightly further apart.  It seems to me that it is good to get separation between the mikes, but the distance will also depend on whether one's playing style uses lots of bellows (and body) movement, because it's desirable to keep the LH side response even, and therefore keep the sound source within the 'cone'.   I think of it like this:  a condenser mike has a narrow 'cone' of roughly even response, and outside that cone, response drops off quickly.  So I am trying to keep the RH side safely within the cone of the mike facing it, and the LH side similarly with the other mike, but such that the centre of the cone is at about the average position of the bellows.  This should give an even response, without noticeable interference between the signals from each mike. 

I wasn't aware of (and have never noticed) the comb effect interference issue IanD describes, but I do see that it can be a problem, (more so with cardiods?) - however if you keep the signals as separate as you can by spacing as I have tried to do, I would have thought that it shoudn't be too much of an issue anyway?  I will also in future try to angle each mike slightly away from the other, which should enhance the separation between the channels still further, without causing too many feedback problems.

However, it seems to me that by far the most important practical issue on stage is that of feedback.  With the arrangement I use, it really minimises this problem - I control the sound desk myself in the band, so I need to be able to hear everybody through the monitor as well as I can.  I have the wedge monitor pretty close to me therefore, about 1-1.5m away from the rear of my mikes.  But I usually find I could easily turn myself up far higher than the other acoustic instruments (particularly flute or violin), without any feedback.

Close miking systems are OK, but they don't seem to give this 'narrow response cone' effect, and I have to say (hopefully not too controversially!), they just do not seem to sound as natural as floor-mounted mikes.  I guess that it is because with a box the sound sources are all separated spatially, so a close mike system has to compromise on the frequency response from each reed - some will be closer than others, and will therefore inevitably sound more 'bassy'.  If this is corrected by equalisation, the other reeds will sound more tinny, won't they?

Another interesting question from this thread for the sound experts - if you have a mike pointing at the bass end from the side, is it possible that the speed of bellows movement is enough to create a noticeable Doppler effect?



I do agree that close mics on the treble end don't sound so good, especially if there are several (uneven pickup and interference effects again). On the bass end all the sound comes out through fairly small groups of holes so a close mic works much better. Bass tip-up only happens when you're within a few inches of the sound source with a cardioid mic, so one on a gooseneck 6" or so long (like the Beyer I use) doesn't suffer noticeably from this.

Anything that increases the separation between mics (so that each picks up mostly one end of the box) will reduce the interference problem -- either placing them at opposite ends, or angling away from each other. The worst position is to have them parallel to each other and fairly close together...

You'd have to move the bellows pretty damn fast to get noticeable Doppler effect -- even if you move a foot in a third of a second that's a pitch change of 0.3%, which is about 5 cents, which will be inaudible over such a short time (not that audible even over a longer time).

Ian
Title: Re: Microphone Placement for Recording
Post by: IanD on October 12, 2009, 11:08:14 PM
Thanks for all the responses guys.  I'm probably going to go with something like the crossed pair a few feet away to go for the "true" sound.  I'm limited by the mics I own and the fact that I can only use one microphone stand (with a T adapter to put two mics on the end).  I'll be making these recordings in the field in Southern Italy in remote areas.  My entire recording set up fits in a backpack which includes a modified mic stand that I shortened substantially with a hack saw ;D


Definitely the best setup now that we know exactly what you want to do :-)

Try crossing the mics at a 90 degree angle with the heads placed one immediately above the other, assuming your mic stand can do this -- in other words if the T adaptor spaces the mics apart, point them inwards towards each other not outwards away from each other.

Don't put them further than about 1m away unless you want to pick up a lot of background and/or room sound. Good windshields are essential!

Good luck!

Ian
Title: Re: Microphone Placement for Recording
Post by: Falseknight on October 12, 2009, 11:54:37 PM
Amazing isn't it? - After, what, 70 years of stereo recording, we come back to stereo crossed pair.  BTW, don't forget that the left mike picks up signal right, and vice versa.
Title: Re: Microphone Placement for Recording
Post by: LJC on October 13, 2009, 08:12:20 AM
You probably get more pitch variation out of the reeds moving differently as the bellows change direction than from the Doppler effect, I never even considered that as a potential problem. Talking from experience: if you get a recording of someone playing really well, that is more important than the sound quality. Just think of all those crackly English one row records of Percy Brown et all (I beleive Alan Lomax recorded them when he was hiding in the UK during the red scare). Its all pretty poor quality and just one mono microphone, but the playing comes through anyway. 
Title: Re: Microphone Placement for Recording
Post by: IanD on October 13, 2009, 06:58:17 PM
Amazing isn't it? - After, what, 70 years of stereo recording, we come back to stereo crossed pair.  BTW, don't forget that the left mike picks up signal right, and vice versa.

Blumlein rules OK :-)

Ian
Title: Re: Microphone Placement for Recording
Post by: Falseknight on October 14, 2009, 07:57:07 AM
Blumlein works best with figure of eight (ideally ribbon) mikes, but that is another game again!
Title: Re: Microphone Placement for Recording
Post by: Simon on October 14, 2009, 11:58:49 AM
Another interesting question from this thread for the sound experts - if you have a mike pointing at the bass end from the side, is it possible that the speed of bellows movement is enough to create a noticeable Doppler effect?
Is that how you get different notes on the push and the pull?   :D
Title: Re: Microphone Placement for Recording
Post by: Simon on October 15, 2009, 01:02:13 PM
The mic heads are about 40 - 60 cm from the melodeon. When recording in stereo, this gives a sufficient L-R separation (but not too much)
This seems to assume that both microphones are directly connected to the corresponding speaker. Systems like microvox record with maximal separation. You can always reduce (or even remove) the separation with the mixer.
Title: Re: Microphone Placement for Recording
Post by: Theo on October 15, 2009, 03:19:24 PM
This seems to assume that both microphones are directly connected to the corresponding speaker. Systems like microvox record with maximal separation. You can always reduce (or even remove) the separation with the mixer.

Yea, but can you remove the crackling from the Microvox connectors?  I never could when I did sound for a Microvoxed fiddle and concertina.
Title: Re: Microphone Placement for Recording
Post by: Lester on October 15, 2009, 03:29:20 PM
This seems to assume that both microphones are directly connected to the corresponding speaker. Systems like microvox record with maximal separation. You can always reduce (or even remove) the separation with the mixer.

Yea, but can you remove the crackling from the Microvox connectors?  I never could when I did sound for a Microvoxed fiddle and concertina.

As I have shortened the leads on my Microvoxes and replaced the connectors with good quality gold plated ones I never have this problem.
Title: Re: Microphone Placement for Recording
Post by: Organettisto on December 10, 2009, 07:01:42 PM
Well, I ended up mostly recording Zampognas and a particular type of folk guitar called a "Chitarra battente."  I did record of couple of organetto tracks during the recording session described below, but during the sessions, all of the recording technique talked about in this thread went out the window.  The environment was what you would label "uncontrolled" as you can see from the youtube videos I posted.   Anyway, I had a blast and got some great recordings, despite the ambient background noise, which I guess just adds to the authentic traditional Italian flavor :)

Blurb:
A few weeks ago I got back from spending 2 weeks in Italy. The main reason for my
trip was to spend time In Rome visiting with the few remaining players of
one of the rarest forms of Italian bagpipe, "Le Ciaramelle d'Amatrice."
There are roughly only 5-6 active players of this zampogna. Fortunately two
of them are in their late 20's early 30's and are both very good players and
are dedicated to continuing this tradition.

The reason I chose to study this particular pipe on my recent trip as
opposed to going elsewhere and immersing myself in one of the other piping
traditions is because of its rarity. Also it appeals to me as a Zampognaro
and amateur ethnomusicolgist of Italian folk music because it is so
different from the other zampognas, not only in the fingering technique for
playing it, but also in its musical scales and their relationship between the two
chanters, the melodic phrases and the rhythmic structure of its traditional
tunes. Not to mention, it's the only zampogna w/o drones!

So I spent a lot of time talking to players and taking notes about the
tradition, and I was fortunate to spend an evening with the bulk of the
members of this musical culture in what I would describe as a "traditional"
ambiance (ie. a huge dinner with lots of wine and singing and piping around
the table) where I made a bunch of field recordings onto a professional
digital recorder for preservation. I was also taking copious pictures and
captured a few video clips as well which are posted below. The singing in the videos
is the traditional style of "stornello" from this region. It is all extemporaneous and
the lyrics are essentially a conversation between the two singers about current events
and observations about the guests sitting around the table. Several times they sang about me
one line going something like "David came from Kansas City and now he is going to bring
the ciaramelle back to Barak Obama!!" I imagine that before tv or radio this would have
been a way for members of the community to discuss news and share the events
of the town.


In addition to making field recordings I took a day trip from Rome to the mountains of
Amatrice. It was breathtakingly beautiful as all the trees were changing. As
we climbed the winding roads in the car there was snow on the ground in the
shaded areas. Going to Amatrice made me realize just how physically isolated
this area was - the perfect place for preserving a musical tradition that is
probably one of the closest unbroken links to the greek Aulos (Tibia) that
is in existence today. The music as described to me by one of the players
was properly "Roman." During my trip to Amatrice I went on what I can only
sum up as a wild goose chase trying to find a wood worker, of who I only had
a first name, Franco, who may or may not have had an old Zampogna that his
father made. To make a long story short, after going from town to town
asking random people for this wood worker, my Italian friend and I ended up
inside the small stone cottage of an old wood worker and his wife heated by
a wood burning stove in the kitchen of which an elderly woman was sitting by
warming herself. I think the last thing that he was expecting to encounter
as his wife roused him from a nap on the couch was to find a young American
standing in his living room very enthusiastically asking about an old
bagpipe. At first they had been holding out on me insisting that there were
no old pipes (this is what they had told my friends in rome as well), but I
think I endeared them enough that the wife, after I made my case, came back
with an old pipe that looked like it had been sitting in the basement for
years. I immediately knew it was the traditional pipe I was looking for and
was excited to get it for a very reasonable price. I then found out that
Franco, the son of the deceased pipe maker who made my pipe has also made a
handful of pipes. I did my best to encourage him to continue making them as
my friends back in Rome would be excited to get a pipe from the region of
Amatrice proper, instead of having to get a pipe maker from Molise to make a
very Molise looking copy.

Anyway, I have the pipe back in the US. After subjecting it to a thorough
cleaning and oiling it looks almost brand new. I put a bag on it and made a
pair of plastic reeds and have it in what I believe to be the proper scale.
I had to figure out the scale by ear. I now see that the tuning is very similar to
the Sicilian pipes, except that the Amatrice pipe has a sharp 4th and is missing the
subtonic note on the right chanter. And of course there are no drone pipes playing the 5th.

David

Videos:

http://www.youtube.com/watch?v=_3hsealpYxU
 http://www.youtube.com/watch?v=uts9HfiWOBg
 http://www.youtube.com/watch?v=zyaL_ayfyxw
 http://www.youtube.com/watch?v=jimCcGD_YYg
 http://www.youtube.com/watch?v=d4BdUHHHcfI
 http://www.youtube.com/watch?v=L7DSsPh4wdw
 http://www.youtube.com/watch?v=bQRISbAexT8
 http://www.youtube.com/watch?v=CYtBNEVk6uA
 http://www.youtube.com/watch?v=OBkxKqr4EJ0

The music scales from the video as I have interpret them:

Left Changer: G#-A#-C-C#-D#
Right Chanter: C#-D#-F-G-G#

My Pipe is playing a half step higher at:
L Chanter: A-B-C#-D-E
R Chanter" D-E-F#-G#-A

Note: The right chanter, though having a thumb hole, only plays 5 notes as
the pinky finger is not used. Notice that two notes overlap between the
chanters.
Title: Re: Microphone Placement for Recording
Post by: rees on December 10, 2009, 07:38:03 PM
Thank you for recounting your Italian adventure.
The videos are priceless.
SimplePortal 2.3.5 © 2008-2012, SimplePortal