Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Vallenato831 on March 24, 2021, 05:31:52 PM

Title: Painting Bellow Frames and other parts.
Post by: Vallenato831 on March 24, 2021, 05:31:52 PM
I have a few Hohner boxes that need some freshening up.  I'd like to repaint the black parts.  Such as the bellow frames, black part of the keyboard and the bassboard cover.   I've attached a few photos showing the areas. 

What type of paint do I use, one that wont leave it sticky to the touch? 
Title: Re: Paiting Bellow Frames and other parts.
Post by: Theo on March 24, 2021, 05:40:48 PM
I’ve had good results with car spray paint.   Check first that the old paint doesn’t react badly.  If the old paint  is deeply chipped or scratched you will need to remove all the old paint if you want a decent finish.
Title: Re: Paiting Bellow Frames and other parts.
Post by: Lester on March 24, 2021, 05:42:00 PM
I’ve had good results with car spray paint.   Check first that the old paint doesn’t react badly.  If the old paint  is deeply chipped or scratched you will need to remove all the old paint if you want a decent finish.
I was about to say this very thing but Theo beat me to it
Title: Re: Paiting Bellow Frames and other parts.
Post by: Vallenato831 on March 24, 2021, 05:48:25 PM
I’ve had good results with car spray paint.   Check first that the old paint doesn’t react badly.  If the old paint  is deeply chipped or scratched you will need to remove all the old paint if you want a decent finish.

I would have never thought that would work!  I was thinking of some kind of roll on paint.   With spray I have to be extremely careful with overspray.  I guess it's all in the prep. 
Title: Re: Paiting Bellow Frames and other parts.
Post by: Helena Handcart on March 24, 2021, 05:50:04 PM
Following advice from Theo I used car spray paint to freshen up some Liliput keyboards, just a quick sand and quick spray and they looked lovely and the finish was not at all out of place.
Title: Re: Paiting Bellow Frames and other parts.
Post by: Andy Next Tune on March 24, 2021, 05:56:06 PM
Yep, I've also had good results with car spray cans. However you do need to disassemble then clean and prep everything thoroughly before spraying.
Title: Re: Paiting Bellow Frames and other parts.
Post by: rees on March 24, 2021, 05:57:04 PM
Overspray can be avoided by using masking tape.
Title: Re: Paiting Bellow Frames and other parts.
Post by: Lester on March 24, 2021, 05:59:41 PM
An alternative for the bellows frames is to use Humbrol model makers enamel which can be brushed on.


Title: Re: Paiting Bellow Frames and other parts.
Post by: Gonk on March 24, 2021, 06:16:53 PM
Might go without saying, but I like the finish that results from drying and sanding between the first coats, medium then fine, then very fine steel wool.
Title: Re: Paiting Bellow Frames and other parts.
Post by: Chris Marriott on March 24, 2021, 06:46:11 PM
For my, ahem, “colourful” Pokerwork I used artist’s acrylic paint and finished it with several coats of satin varnish.
Title: Re: Paiting Bellow Frames and other parts.
Post by: Graham Spencer on March 24, 2021, 07:22:08 PM
Yep, I've also had good results with car spray cans. However you do need to disassemble then clean and prep everything thoroughly before spraying.

Same here - I keep a can of "matt" (I find it doesn't dry dead matt, but has just a tiny hint of satin finish that I really like) black car spray in the workshop at all times, and usually have a small selection of other useful colours knocking about.  Thorough prep is essential for good results.
Title: Re: Paiting Bellow Frames and other parts.
Post by: Vallenato831 on March 24, 2021, 07:28:04 PM
Overspray can be avoided by using masking tape.

What worries me is the bellow frames, dont want to risk damaging the bellows.  For the keyboard, should be straight forward.  I'm going to find some of that models brush on paint that Lester recommends. 
Title: Re: Paiting Bellow Frames and other parts.
Post by: Steve_freereeder on March 24, 2021, 07:31:58 PM
An alternative for the bellows frames is to use Humbrol model makers enamel which can be brushed on.

Yes - I've used that for bellows frames. It's good and hard-wearing.
Title: Re: Paiting Bellow Frames and other parts.
Post by: Chris Marriott on March 24, 2021, 07:43:04 PM
An alternative for the bellows frames is to use Humbrol model makers enamel which can be brushed on.

Yes - I've used that for bellows frames. It's good and hard-wearing.

Yes, my acrylic paint isn’t very tough. Hence the varnish to protect it.
Title: Re: Painting Bellow Frames and other parts.
Post by: diatonix on March 24, 2021, 09:30:59 PM
I too use car spray paint. In the case of bellows frames I spray a generous amount on to a piece of wood or card board and then use a small paint brush. Wear a gas mask, the stuff is nasty.
Title: Re: Painting Bellow Frames and other parts.
Post by: Stiamh on March 24, 2021, 09:50:14 PM
For my, ahem, “colourful” Pokerwork I used artist’s acrylic paint and finished it with several coats of satin varnish.

Love it!
Title: Re: Painting Bellow Frames and other parts.
Post by: Chris Marriott on March 24, 2021, 09:56:30 PM
For my, ahem, “colourful” Pokerwork I used artist’s acrylic paint and finished it with several coats of satin varnish.

Love it!

Completely unsellable now, probably 😁
Title: Re: Painting Bellow Frames and other parts.
Post by: Grumpy on March 24, 2021, 10:56:01 PM
Smooth gloss black Hammerite is a perfect match to Liliput, dries quickly to a super hard finish and has no stickyness even in summer sun. A little expensive but tin lasts along time.
Title: Re: Paiting Bellow Frames and other parts.
Post by: Vallenato831 on March 24, 2021, 11:07:32 PM
An alternative for the bellows frames is to use Humbrol model makers enamel which can be brushed on.

Is this the right stuff?

https://modelmerchants.com/shop/humbrol-21-black-gloss-enamel-paint-14ml-45-oz-aa0237/
Title: Re: Paiting Bellow Frames and other parts.
Post by: Steve_freereeder on March 24, 2021, 11:58:12 PM
An alternative for the bellows frames is to use Humbrol model makers enamel which can be brushed on.

Is this the right stuff?

https://modelmerchants.com/shop/humbrol-21-black-gloss-enamel-paint-14ml-45-oz-aa0237/

Yes - that's the stuff!
Title: Re: Painting Bellow Frames and other parts.
Post by: Vallenato831 on March 25, 2021, 02:26:05 AM
Thanks Steve
SimplePortal 2.3.5 © 2008-2012, SimplePortal