Melodeon.net Forums
Discussions => Instrument Makes and Models => Topic started by: Matthew B on May 11, 2021, 10:59:26 PM
-
On Friday I had my first ever squeeze of a Hohner Morino Club, courtesy of Gonk. Wow. Just wow. What an amazing piece of machinery. Five minutes, and Gonk's neighbor evicted me for disturbing the peace.
I have never played a Castagnari, so I can't judge against that standard, but those big Hohners are, without a doubt, most remarkable.
So thanks Gonk, more noise follows! Anyone else have the measure of these mighty machines?
-
I bought one a couple of years ago on Ebay de. What a big sound and so easy to play! I'm used to playing quite a heavy Italian box so didn't find the size or weight a problem. It's currently being retuned to D/G club to be a backup of my usual one.
-
Are these the ones with cassotto on the L voice?
Do you know their size and weight?
-
-Y-, yep, L and M in cassotto, LMMMH in total... weight: 18 lbs / 8.15 kg, dimensions when sitting on lap: 14" high x 8.5" deep / 35.5 cm x 21.5cm. (The measure of the machine.)
In fairness to my (downstairs) neighbor, I think she really drew the line at our podorythmie...
-
all the morino instruments are top notch including the piano and continental boxes. My only criticism of the 'melodeon' version is that it has only 18 push pull bases.
to me the 3 row shand MOrino with 80 or 96 bass mokes more sense as 12 keys on the treble are relatively easy ( just 5 scalewoth of learning) and there is bass for everything in a very logical layout.
But each to his own ( i think Mark Basely of the dartmoor pixies plays the melodeon version)
george
-
I bought one a couple of years ago on Ebay de. What a big sound and so easy to play! I'm used to playing quite a heavy Italian box so didn't find the size or weight a problem. It's currently being retuned to D/G club to be a backup of my usual one.
The retuning of such a large and complex machine must be a pretty substantial undertaking. I am suitably impressed. Perhaps you could post a sample of the result when it's done?
-
I bought one a couple of years ago on Ebay de. What a big sound and so easy to play! I'm used to playing quite a heavy Italian box so didn't find the size or weight a problem. It's currently being retuned to D/G club to be a backup of my usual one.
The retuning of such a large and complex machine must be a pretty substantial undertaking. I am suitably impressed. Perhaps you could post a sample of the result when it's done?
Yes. It's taking a long time but I will post a clip when I get it back.
-
which tuner is doing it
g
-
Here's a picture of a retuned and extensively modified Hohner Morino Club. The treble end was retuned to BCC# and the bass end modified to include the 60 bass innards from a small CBA. Apologies for the size and quality of the pic; it was cropped from a much bigger collection of boxes.
There's also a short YouTube clip of it being played by its owner, Graeme Mackay, before the bass modification, with a selection of some of the different couplers. https://youtu.be/AZ8_9gu2bvE
-
which tuner is doing it
g
PM on it's way.
-
Hello,
Does anyone know the difference in the Hohner Morino Club,Morino Club N,Morino Club S and Overture reeds.
Thanks.
-
I have a Morino Club S with Midi factory installed.
It is a pleasure to play but have never been able to figure out if the midi works or how to connect it. There is a 5 pin connector on front but not standard midi cable. With some research ; I have concluded that it requires a box which likely provides power for the midi. I have found a picture of a hohner interface box which I have attached along with 5-pin connector. Does anyone have experience with this type of interface box and what it does and how to replicate it. ? THx; Don.
-
The little box should feed into any midi voice module which then outputs to an amp. I used a Boss module into a Roland keyboard amp. It may work "out of the box" or it may require cleaning of contacts/components depending on the system installed. Re-triggering is the most common problem and is likely from dirty contacts or corrosion.
-
But each to his own ( i think Mark Basely of the dartmoor pixies plays the melodeon version)
george
Mark BaZeley does indeed...Bob Cann's box re-tuned to D/G by Ivor Hyde but with the gleichton retained... :|glug
-
The little box should feed into any midi voice module which then outputs to an amp. I used a Boss module into a Roland keyboard amp. It may work "out of the box" or it may require cleaning of contacts/components depending on the system installed. Re-triggering is the most common problem and is likely from dirty contacts or corrosion.
The box output would likely be a standard midi out signal as you indicate. The problem is I do not have this converter box and wish to build or purchase a suitable replacement which would provide suitable power for the midi system and a standard output midi connection. THx; Don
-
I have a Morino Club S with Midi factory installed.
It is a pleasure to play but have never been able to figure out if the midi works or how to connect it. There is a 5 pin connector on front but not standard midi cable. With some research ; I have concluded that it requires a box which likely provides power for the midi. I have found a picture of a hohner interface box which I have attached along with 5-pin connector. Does anyone have experience with this type of interface box and what it does and how to replicate it. ? THx; Don.
You might try a polite enquiry to Rod Stradling (NOT the melodeon player). He has some information about accordion MIDI here (https://www.rodstradling.co.uk/accmidicable/index.html). It's not the same as the system you need but he might be able to point you in the right direction.
-
Thanks for tip. I was in contact with Rod; unfortunately there is very little info available for these proprietary hohner expander boxes.
-
My guess is that there is a printed circuit board inside the Morino that generates the MIDI codes and that the interface box powers this. There may be some printing on the board that will tell you the voltage required. The interface box uses a 180deg DIN connector for MIDI out and a 240deg connector for the Morino so you can't misconnect them. I doubt that the interface box does anything to the MIDI signal other than link the two connectors.
There is very good tutorial on MIDI hardware and signal formats on the Sparkfun website. You don't have to be an engineer to understand it but it would help if you have a little electronics knowledge.
Good luck!
-
My guess is that there is a printed circuit board inside the Morino that generates the MIDI codes and that the interface box powers this. There may be some printing on the board that will tell you the voltage required. The interface box uses a 180deg DIN connector for MIDI out and a 240deg connector for the Morino so you can't misconnect them. I doubt that the interface box does anything to the MIDI signal other than link the two connectors.
There is very good tutorial on MIDI hardware and signal formats on the Sparkfun website. You don't have to be an engineer to understand it but it would help if you have a little electronics knowledge.
Good luck!
Thanks; JD for your detailed reply; I was hoping that this would be the case. If the box is only providing power and converting cables; I may be able to convert it to run with widi jack (bluetooth) which provides 5 Volt power. ( I still have to check inside to see if it is actually 5 volt required and the internal midi printed circuit board exists and all pickups are ok) (If it was 9v required for example ;then a conversion to 5volt would be required for midi). Perhaps the dc for circuitry come from the separate plug beside the midi connector. I will take some pictures and share them . Thank You. ; Don
-
My guess is that there is a printed circuit board inside the Morino that generates the MIDI codes and that the interface box powers this. There may be some printing on the board that will tell you the voltage required. The interface box uses a 180deg DIN connector for MIDI out and a 240deg connector for the Morino so you can't misconnect them. I doubt that the interface box does anything to the MIDI signal other than link the two connectors.
There is very good tutorial on MIDI hardware and signal formats on the Sparkfun website. You don't have to be an engineer to understand it but it would help if you have a little electronics knowledge.
Good luck!
I have now attached some pictures inside the morino club.
Will need it !
-
I can see from the first photo that there are 4 wires connected to the din socket on the left, Red, yellow, violet, black. It looks as if they go all the way across to the far right and the black and red go to what looks like a regulator on a black heat sink and the other two to a connector on the board. It seems likely that the red and black are the power supply and yellow and violet the midi out. The regulator should have a number on it something like 7805. If that is the case the 05 indicates that it’s a 5v regulator so it will need an input voltage of at least 7v - a 9v power supply would be ok.
All of this needs verifying of course.
Is the connector next to the din socket a jack socket? Does it go to the internal mic shown in one of the other photos?
-
The first thing that jumped out at me was the mounting of the reeds on the treble side. I assume those are the "L" reeds mounted parallel to the fondo. Is that a bit like the arrangement in a Preciosa but on a larger scale?
Shame we can't quite see the labeling of the chips on the board. I would agree with Howard that there is probably a 7805 regulator mounted on the heatsink. If that is the case then the power for the board is coming from the 240deg DIN socket, probably 9 volts. So the four wires from the DIN would be 0v, 9v and MIDI out and possibly 5v out. That allows the interface box to provide power for the MIDI electronics and the three wires required for the standard MIDI interface without any extra electronics actually inside the box.
It looks like the internal microphone is connected to the extra jack socket on the case. This is a rare beast.
When was this installation done I wonder. 1980s or 90s?
-
The first thing that jumped out at me was the mounting of the reeds on the treble side. I assume those are the "L" reeds mounted parallel to the fondo. Is that a bit like the arrangement in a Preciosa but on a larger scale?
Not the same apart from the orientation. Those reeds are in a cassotto chamber.
(http://www.accordions.co.uk/images/Siteimagery/Cttoxsec.jpg)
-
Thanks Howard and JD for your analysis;
Indeed you are correct. It is a 7805 regulator. pics attached.
Don.
-
The large IC EF68B50 is a UART, proving the serial output for the MIDI interface. It looks like it’s connected to the smaller chip CD74HCT03 next to it. This is an open drain nand gate which provides the driving current for the MIDI output. It normally has a 220 ohm resistor from its output to one of the midi pins and the other pin is connected to +5 volts via another 220ohm resistor. Right next to the adjacent connector for the yellow and violet wires are two resistors colour coded red, red, brown = 220 ohms.
I’d say there’s a good chance you’ll be able to connect a 9v power supply and split off a standard midi signal to go to a synth of your choice. It just needs some probing with a meter to verify all of this and check the polarity of the power supply and the midi connections.
From the date codes on the chips I’d say this was made about 1987.
-
This tech info is greatly appreciated. It clarifies the function of the "special box" which I will replicate. I will check further on what the phono jack connects to.
Dates of manufacture for Hohner Morino Club "S" from 1987 to 2006
per Hohner website.
-
Update on midi discussion for morino. I have now completed midi box _ picture attached.
It works great with the V3control module (chord ch2 bass ch3 treble ch1). It seems very responsive to bellows direction change and always sends correct midi note. Volume does not change with bellows pressure. I would like to know how it is determining bellows direction (pressure transducer?)
-
Congratulations on making this work. Imagine how much Hohner would charge for an interface box with just a few wires inside!
It might be worth using a MIDI logging program to check for "expression" values. A value from the pressure sensor might be sent as expression rather than volume. This is used to simulate a swell pedal on some synths. Whether your V3 module could use it is another question.
As for the pressure sensor, is it the component that looks like a microphone mounted on one of the blocks? I always thought that a MIDI accordion would use two pressure sensors, one inside the bellows and one outside. I know the Streb only uses one.
-
I’m guessing here-
The circuitry at the left of the board looks like something linear, maybe an A to D. There are 2 red preset pots, possibly gain and offset. If the gain is set high the bellows pressure would appear on or off as you report.
Is there a pressure sensor something like one of these somewhere https://datasheet.octopart.com/MPX5010DP-Freescale-Semiconductor-datasheet-98060.pdf
The round object mounted on a rubber suspension attached to the block is an internal microphone.
If you could send a pic of the numbers on the chips on the left it might be possible to work out more.