Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: dino.pafftti on May 29, 2021, 12:06:47 PM
-
I promised to take pictures of rusty reeds Theo .... in these a lot of rust, I do not know,, can restore them ?? I think G / C
-
I would expect them to clean up fine.
-
Yes .. Theo promised to tell me how I can remove the rust,
-
Yes they should be fine once cleaned.
Tools I use:
Support plate same as used for tuning
Polishing block - coarse https://www.amazon.co.uk/Garryson-Garryflex-Abrasive-Block-120grit/dp/B0001P08UQ
Small screwdrivers
For the top surface support the reed tongue and rub with the polishing block. This will remove most rust but doesn’t remove any significant amount of steel. Any coarse lumps of rust that resist the polishing block might need to be scraped with a screwdriver or something else with a hard edge. I prefer not to use a file because it’s too easy to remove steel as well as rust.
For the underside place the reed plate on a flat smooth surface and scrape with a small screwdriver. You can get quite cheap sets of “jewellers screwdrivers†which are fine fir this.
Finally I’d give each side of the plate a light rub with a soft wire brush to remove any loose debris.
Important: when using any of these methods always work away from the rivet and toward the free end of the reed.
-
Yes .. Theo promised to tell me how I can remove the rust,
I would use these (https://www.amazon.co.uk/Garryson-Garryflex-Abrasive-Block-240grit/dp/B0001P08UG) to clean the top of the reeds whilst supporting the tongue with a pinger. Any rust on the inside of the reeds can normally be scraped off with a screwdriver blade. I would then go over the reed plates with a brass brush (https://www.amazon.co.uk/Brushes-Plastic-Handles-Cleaning-Welding/dp/B08GXXMTTF/ref=sr_1_3?dchild=1&keywords=brass+brush&qid=1622288011&s=diy&sr=1-3).
Edit; Same as Theo then (:)
-
Though with a different grade of polishing block!
I do have 3 grades but for the degree of rust in the photos I think the coarse would be most effective.
-
Being non(un)professional, I've used a rust removing fluid with great success. It's called Evaporust and it's very easy to use and is even safely disposable! I got it off eBay, where it was cheap enough for even me to buy it!
-
Thanks everyone, I try to find the right tools for myself (:)
-
most folks seem to use acetone to clean off all the crud (old wax and glue and nicotine ). comes off nice with a soak and a cotton bud and eyebrow cotton buds for the smaller reeds. I use a two bath process. first one to take out the hardcore stuff. then into second bath for a cleaner clean. For those reeds I'd go acetone first so i get rid off all the crud. Then the gentle scraping and abrasive block or flexfile mini sanding sticks. Then more acetone to clean off again. Obviously tuning will be needed after removing rust and putting on new valves. I cleaned some recently and on some reeds the rust was worse at the rivet end and they were all 50 cents flat after removing rust.
-
I used a piece of medium fine Emory cloth tape to clean the underside of reed (part way) by slipping a piece of Emory cloth in under the reed as you would a pinger and pulled back the Emory cloth towards the tip of reed once or twice , then scraped close to the rivet with a screwdriver. Probably frowned upon but it worked well on the beat up hohner I was fixing. I was careful to keep the Emory cloth flat and no pressure was applied or at least not much so that I didn’t remove rust from the edge and not the middle, which I assume would be the reason for not doing it this way.
No detectable reed material was removed other than surface rust.