Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Squeaky Pete on May 07, 2022, 02:25:16 PM
-
My HA114 has been worked hard over the last couple of months.
I knew the wax wasn't in the best of order and a couple of plates were rattling around when I got it.
Now a buzz has started on one button and another is slightly out of tune, so it's clear I need to strip it and renew the wax and valves.
This is the version with 2 parallel blocks glued in place and there's not much room. I had no problems working on the other 4 stop with flat mounted reeds.
Any tips on waxing? I normally use either a brush (very slow) or a flat spoon which I'm not sure I've got room for. I could make a special one....
-
Here be dragons!
My hands aren't steady enough to make an even half decent job of them. Good luck!!
-
Gravity is your friend here. It is possible to run molten wax along the gap between two reed plates. Position the box so that there is a slight slope to get the wax running in the right direction. When placing the reds put a coat of melted wax on the end that is furthest from the top of the reed block. This seals the end of the reed and helps to hold the reed plate in place while you wax the edges.
-
In a similar way to Theo's method I attach a small bead of wax to the bottom of the reed then slide it in place, then wax the top of the reed and use gravity for the sides.
-
Right.
I'm going in.
Just not yet
-
"Just not yet"
Chicken!!!
-
"Just not yet"
Chicken!!!
Possibly. But.....
I have a couple of more pressing jobs already laid out.
I thought, just for a change, that I'd ask advice before I started. I might remelt around the buzzy reed just to keep it going, but it does need serious attention.
-
I’ve watched a fella dip the rivet end just a little into wax then pop into
position on reed block before pouring wax between plates .
I’ve yet to give in a go.
-
Try not to drop the whole reed into the wax pot. I, uh, know someone who did that once.
-
Do they float ?? ;)
-
I'll ask.
-
;D
-
Somebody here reading this has a wicked sense of humour.
I got a large packet in the post and I now have two to do.
-
Well it's not pretty but seems to work.
I now have another problem, playing the higher notes I am getting bleed of air from the note I'm playing to nearby ones. Is this a job for getting the reed block of and re gluing?
Is there a better way or am I missing something?
-
It could be air leaking through a loose or misaligned register slide. First thing to check is that the register slides are travelling the correct amount so that they open and close fully. Or if it’s the same note that’s sounding it could be a split if knot hole in the midrib of the block. The chamber walls are fairly thick in a 114 so damage to the wood is unlikely. Another possibility is a cracked glue line at the top or at the base of the block.
-
It has been repaired in the past and not aligned properly.
The slide had a couple of links in it.
The base of the reed block had a crack in it, glued up with some brittle clear glue, very different from the usual brownish stuff.
Now it's going to be interesting getting it back together.
-
It turned out that the base of the block where the slide works was uneven and the air could leak along this.
As this was a HA113 for a friend I couldn't risk it coming back to me. It had to be a proper final repair, not a make do for myself.
I slowly and very gently rocked the block until the the glue gave way and then I could flat it on a long standing block.
I took this opportunity to make sure the wax was ok
I was terrified to think I'd do all the work and there would still be an air leak so I made a very bodgy attempt to hold it in final position and confirm it seated properly. Second time it worked after removal of a stubborn bit of glue and I was able to play it.
I then glued up and used the same Heath Robinson system to hold it .
Success!!
-
Necessity being the Mother of invention, well done!
-
“ I slowly and very gently rocked the block until the glue gave way...â€
I have never achieved this, always been too wary of damaging the delicate slide cut outs!
I must say “ Well done!â€
-
An old 3 stop of mine, with the single reedset block being removable.
(Posted on here in the past - Credit to P.Grassby of Coventry.)
-
My method is to remove all the reeds and then place it over a pan of boiling water, reed-blocks facing into the pan..
This softens the glue and the blocks come out easily.
It's worth blocking off the rest of the treble end to keep the steam away from the other glued parts, otherwise the whole thing could fall apart.
-
I think I'm going to try that.
Sometime ago I bought a C/C# from a seller in Edinburgh that turned out to quie literally have had the reed blocks smashed. Obviously the e-bay seller was a con artist but i didn't return the box because I had bought it to see what it's tuning was like ( I have found a tendency for old boxes sourced in Edinburgh to be High Pitch tuned whereas ones coming from Glasgow and Aberdeen tend to be A 435 but my sample is statistically insignificant).
Anyway... I think I'll try Rees method possibly using an old mess tin...I rather like the idea of re-fittng this yoke with removable reed blocks so I can have a German Type 4 bass D/G. ( Thread de-railment not intended)
-
My method is to remove all the reeds and then place it over a pan of boiling water, reed-blocks facing into the pan..
This softens the glue and the blocks come out easily.
It's worth blocking off the rest of the treble end to keep the steam away from the other glued parts, otherwise the whole thing could fall apart.
As luck would have it, one of my students brought in an old 4 stop which a friend had found in a house in that London which they were just about to pull down. I said I'd see if I could tart it up a bit. A quick gawp inside revealed some flaky wax and one loose reed. Life will be easier if the blocks were removed I guess.
Now, might a hot air gun, on a low setting do the same job, or is the moisture a key ingredient. I understand hot hide glue melts at around 6o C
-
It might work, Ed. If no luck with that, try a blowlamp.
That should sort the job out once and for all. >:E
-
A steam cleaner gun may be the ticket. Often comes with hose accessory so you can keep the action local.