Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Squeaky Pete on June 20, 2022, 11:22:35 AM

Title: Keyboard material
Post by: Squeaky Pete on June 20, 2022, 11:22:35 AM
I'm playing about with moving button placement on an old club box and there will be holes missing and unused holes.
What material is used, or could be used to make a new keyboard?
I don't really want to patch anything if I can help it.
Title: Re: Keyboard material
Post by: Theo on June 20, 2022, 12:07:12 PM
The original top is celluloid.   It's unlikely you can find celluloid today in that is thick enough.  You might be able to use modern plastic.  Delrin/Acetal would be ideal.  Acrylic might work, but can be brittle.   Sheet aluminium would work too.
Title: Re: Keyboard material
Post by: Winston Smith on June 20, 2022, 03:29:45 PM
I used aluminium sheet on my bass thing, and it worked out fine. It would have looked better plated than polished, but that would have cost money!!!
But, of course, it doesn't look original any more.
Title: Re: Keyboard material
Post by: Graham Spencer on June 20, 2022, 07:10:58 PM
Would styrene sheet (eg "Plasikard") work? It's easily worked and readily available in thicknesses from 0.25mm to at least 1.5mm and comes in both black and white.  I've nver tried it for this job, and it may not be sufficiently rigid, but it might be worth a look.

Graham
Title: Re: Keyboard material
Post by: rees on June 20, 2022, 11:00:07 PM
Good results can be had with high quality aircraft ply. I can spare some in 3mm or 1.5mm.
Title: Re: Keyboard material
Post by: chris hall on June 21, 2022, 03:16:24 PM
After a chat with pete at acorn i decided to make some fingerboards from scratch for one rows and (when we get round to it two rows)...he also advised aircraft play for the tops which worked out good.....we ended up using 4mm ply stained with several coats of black liberon spirit stain and finished with 5 or 6 coats of liberon finishing oil. stain and oil was applied both sides to prevent warping. If you like black it looks good. Wear gloves and do it in a well ventilated space. its time consuming but not hard. hardest bit is finding tiny screws if you want it to be removeable.
Title: Re: Keyboard material
Post by: Graham W on June 21, 2022, 04:03:21 PM
Another vote for 'aircraft' ply. This one is finished with acrylic spray paint and lacquer and has a removeable back.

I've had good results using black acrylic sheet to replace an old celluloid top with something that looks reasonably similar.
As Theo says it can be brittle, but with care (mounted rigidly in a mill or drill press and cut with a very sharp tool and not too fast) it's fine.

Good luck.

Title: Re: Keyboard material
Post by: Squeaky Pete on June 21, 2022, 04:16:27 PM
As I have some ply at just under 2mm, I will use that. I've been using it for spines of reed blocks.
Either doubled or maybe I'll stick a walnut veneer either side so it's easier to stain and polish.
I like the idea of acrylic, but the ply is here and available.
Title: Re: Keyboard material
Post by: Winston Smith on June 22, 2022, 01:58:43 PM
"but the ply is here and available"

That's what I like to hear! (As Lieutenant Kojak was once heard to misquote, "Waste not; why not?") 
Title: Re: Keyboard material
Post by: Graham Spencer on June 22, 2022, 05:06:27 PM
"but the ply is here and available"

That's what I like to hear! (As Lieutenant Kojak was once heard to misquote, "Waste not; why not?")

Hear hear! If you've got a material in stock that will do the job, then why waste time, money and nervous energy buying something else that might or might not be a little better (or a little worse)?

Graham
Title: Re: Keyboard material
Post by: Kimric Smythe on June 23, 2022, 04:53:37 PM
i made some keyboards with aircraft ply for the top, I skinned it with a hardwood veneer and parquetry trim. https://flic.kr/p/b4UweZ   I have pieces of regular thickness celluloid that are probably big enough in several colors that would work if glued to a ply or aluminum backing.
Title: Re: Keyboard material
Post by: Winston Smith on June 23, 2022, 05:57:40 PM
"https://flic.kr/p/b4UweZ (https://flic.kr/p/b4UweZ)"

I really should stop looking at your pictures and/or videos as they make me feel so inadequate. Your work is always excellent!
Title: Re: Keyboard material
Post by: Kimric Smythe on November 13, 2022, 05:32:29 PM
Thanks. Did you check out the cosplay armor I make for the Mad Max crowd?
SimplePortal 2.3.5 © 2008-2012, SimplePortal