Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Martyn Hunter-Wyatt on September 03, 2022, 01:44:21 PM

Title: Hohner T Dot Reeds
Post by: Martyn Hunter-Wyatt on September 03, 2022, 01:44:21 PM
I'm sure someone must know this.  What does a dot next to the T on a Hohner  aluminium reed plate mean? The only answer I've found so far is that they're PA reeds, but these are in a melodeon.  It says Made in Germany on the outside but I don't know it's history, it could be a marriage.
Title: Re: Hohner T Dot Reeds
Post by: Pete Dunk on September 03, 2022, 02:02:51 PM
I have a couple of Hohner PAs here, no dots next to the T on these plates.
Title: Re: Hohner T Dot Reeds
Post by: Martyn Hunter-Wyatt on September 03, 2022, 02:43:29 PM
Maybe not to do with PAs then. These have a definite dot. I wondered if they are Chinese, the reeds are in good condition, better than the box. It doesn’t look much messed about with though. Most instruments I’ve worked on so far have been a right mess inside, this looks a bit too pristine.
Title: Re: Hohner T Dot Reeds
Post by: Theo on September 03, 2022, 04:01:14 PM
I’m sure they are not Chinese.  All the Chinese Hohner reeds Ives seen just have a  plainT that is not very deeply pressed into the metal.
Title: Re: Hohner T Dot Reeds
Post by: Tone Dumb Greg on September 03, 2022, 05:22:47 PM
Could they be a fettler's punch marks showing which way is up?
Title: Re: Hohner T Dot Reeds
Post by: Pete Dunk on September 03, 2022, 05:43:40 PM
The T shows which way is up, perhaps the punch marks are a fettler’s mark to show that this plate is tuned. Seems a bit excessive though.  ::)
Title: Re: Hohner T Dot Reeds
Post by: Martyn Hunter-Wyatt on September 03, 2022, 06:11:58 PM
It seems quite well tuned. I’ll take fettler’s mark unless anyone else has a better idea. It has some tuning scratches but doesn’t look as though much else has been done, unless it’s well disguised.
Title: Re: Hohner T Dot Reeds
Post by: Theo on September 03, 2022, 07:00:49 PM
I’m pretty sure they are a Hohner factory mark and not a tuners mark added later. I have a suspicion that they are slightly better quality than standard T reeds.
Title: Re: Hohner T Dot Reeds
Post by: Martyn Hunter-Wyatt on September 03, 2022, 07:28:48 PM
Thanks Theo, it sounds encouraging. It’s an HA114. Seems pristine inside but it’s had a lot of wear outside. I was just wondering if it had been rebuilt somehow. Bellows are good, reeds excellent but plenty of rust and playing wear externally. A bit of de-clacking and cleaning up and I’ll be happy with it.
Title: Re: Hohner T Dot Reeds
Post by: jarviw on September 04, 2022, 03:13:00 AM
For those of you non-Chinese instrument collectors  :D  here are my Chinese Hohner Panther bass reeds.
The smaller chord reeds have better T stamping, vs the large bass reeds with faint stamping.

My panther has the old Corso style grill (not sure when they switch to the new one with Panther logo), so probably more than a few years old.
Title: Re: Hohner T Dot Reeds
Post by: Pete Dunk on September 04, 2022, 01:06:27 PM
Well, well, well. I decided to give my 1040C a brush up tuning today and was surprised to find that most of the treble reeds are marked “H.” rather than the more usual “H”. It would seem that the practice of adding a dot started before T reeds became more common. I’ll post a pic later once I’ve had time to reduce the file size.
Title: Re: Hohner T Dot Reeds
Post by: Rog on September 04, 2022, 05:05:21 PM
 (:) Presumably the dot is part of a single 'H.' punch, rather than a little helper stamping the dot separately
Title: Re: Hohner T Dot Reeds
Post by: Pete Dunk on September 04, 2022, 06:23:19 PM
it would appear so Roger. The markings are all identical and that would be nigh on impossible to do freehand.
Title: Re: Hohner T Dot Reeds
Post by: Winston Smith on September 14, 2022, 01:10:10 PM
I hadn't seen these dotted reeds either, but those on which I was actually working at the time had them! I was much surprised that I hadn't noticed before. Mind you, when I flipped the reeds over; I also noticed a dot on the reverse too! (The plot thickens?)
Title: Re: Hohner T Dot Reeds
Post by: Pete Dunk on September 14, 2022, 10:20:11 PM
I was working on a Club 111B MMM today and the chord reeds were all H reeds. I had to remove a few reed plates to sort out problems with the inner reed gap setting (reeds nailed in place on leather gaskets), these plates were all dot punched on the inside face. I've worked on this box before and had never noticed this, it's odd that it escaped my attention I'm usually quite observant.
SimplePortal 2.3.5 © 2008-2012, SimplePortal