Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: jarviw on November 01, 2022, 06:27:45 PM

Title: Wooden buttons
Post by: jarviw on November 01, 2022, 06:27:45 PM
So I had the crazy idea of making my own wooden buttons... Hohner treble buttons are about half an inch in diameter, which I can get in both soft and hard woods dowels readily. And I think a small hole in the backside with some epoxy glue will hold them on the mechanism nicely. Obviously there will be a bit of sanding for the rounded profile as well as polishing, but surely it's doable?
Title: Re: Wooden buttons
Post by: mselic on November 01, 2022, 06:48:27 PM
I've done it once before for a concertina that was being restored for sentimental value (it being a cheap instrument that did not have any real value otherwise).  I made them out of wooden dowels as you are suggesting.
Title: Re: Wooden buttons
Post by: Theo on November 01, 2022, 06:49:29 PM
I'm sure it is do-able, but end grain on the top of the button might not be comfortable.
Title: Re: Wooden buttons
Post by: Tone Dumb Greg on November 01, 2022, 07:53:14 PM
I did this on a concertina. It was easy enough, but it wasn't 100% successful. I used soft wood dowel and they lasted about five minutes. The box had rubbish reeds. I threw it out in the end.

Why not just buy some Hohner buttons, or scrounge them out of a scrap box?
Title: Re: Wooden buttons
Post by: Trevor Henderson on November 01, 2022, 07:58:36 PM
I made wooden buttons out of 7/16” hardwood dowel. I put them in a small drill press and used sand paper to shape and smooth the tops. They’ve held up for 15years of daily playing
Title: Re: Wooden buttons
Post by: tirpous on November 01, 2022, 09:21:57 PM
Plug cutters are available in various sizes if one wants to make buttons with side-grain.  And a closed-grain hardwood would probably work best, no matter which way the grain is running.
Title: Re: Wooden buttons
Post by: Steve C. on November 02, 2022, 08:51:45 AM
Impractical, sure.  Fun, yes.
Lots of places sell scrap exotic wood cutoffs and Tirpous idea to use plug cutter would work nicely to get off-grain cuts.
Title: Re: Wooden buttons
Post by: jarviw on November 02, 2022, 03:16:57 PM
No, I don't actually *need* any buttons (yet). It was really just a crazy idea for the sake of entertainment.
and yes, I thought about using a plug cutter for cross grain cuts first, but thought a dowel would make the process easier: Round off the ends on a belt sander for the profile, then cut the buttons out on a band saw for consistent thickness. And a few coats of varnish with fine sanding in between will smooth anything out  ;D
Title: Re: Wooden buttons
Post by: Tone Dumb Greg on November 02, 2022, 08:59:47 PM
A lathe (table top versions are available if you don't have access to a half decent workshop) would be my tool of choice for the job.
Title: Re: Wooden buttons
Post by: boxcall on November 02, 2022, 11:48:08 PM
No, I don't actually *need* any buttons (yet). It was really just a crazy idea for the sake of entertainment.
and yes, I thought about using a plug cutter for cross grain cuts first, but thought a dowel would make the process easier: Round off the ends on a belt sander for the profile, then cut the buttons out on a band saw for consistent thickness. And a few coats of varnish with fine sanding in between will smooth anything out  ;D

If you use a bung cutter to cut them it would round the end for you.
You may need to adjust the round?
Title: Re: Wooden buttons
Post by: Kimric Smythe on November 13, 2022, 05:27:32 PM
You can use a nice hardwood and then "paint" the button with the wood workers super thin superglue (about the viscosity of alcohol) it will soak in the wood and harden the surface. It takes a nice polish too. This would seal a endgrain nicely.
Title: Re: Wooden buttons
Post by: Graham Spencer on November 14, 2022, 11:50:43 AM
I'm sure it is do-able, but end grain on the top of the button might not be comfortable.

I agree - and they would be considerably more liable to split with the grain running along the length. Plug cutters would work provided you can find a size near enough to your required diameter, though it shouldn't be too difficult to find a friendly woodwork enthusiast who would turn you up a set. I'd offer, but I'm 2000 miles away from the UK........
SimplePortal 2.3.5 © 2008-2012, SimplePortal