Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Sandy Flett on January 05, 2023, 05:01:08 PM
-
I have been playing my DB Carnival II a lot more than usual recently and noticed today that the A button in the middle of the D-row has suddenly gone a bit stiff. It still opens and closes the pallet. I have taken the cover off and everything looks normal. What can I do to restore it to its light touch?
-
It's a simple problem, but usually not so simple to solve. The Carnival has a traditional keyboard with wooden levers. This design is prone to the type of problem you are experiencing. Sometimes it can happen as a result of humidity changes causing the lever to distort slightly so it rubs on the side of its housing. In this case it should resolve without further attention. More often it is because the lever has become a tight fit on the axle rod which might be due to some dust or grit getting in there, or occasionally to corrosion on the axle rod. The only permanent solution is to strip down the keyboard, clean the axle rod and the holes in the levers, and reassemble the keyboard. This is not an easy diy task. All levers must go back in the same place, and cleaning the lever holes has to be done with extreme care because even a tiny enlargement of the hole can result in a key the can move sideways by an excessive amount.
Don't be tempted to add any lubricant or to poke anything down the side of the lever which won't help and might make things worse.
-
Thanks, Theo. Could it do any harm if I keep playing it to see if it resolves on its own?
-
Hi Sandy. You could try keeping it in a warmer room than usual. This will often do the trick as the wood will shrink slightly.
One of my own boxes does this - if I keep it in the workshop the button sticks but after a few days in the lounge it's fine again.
I'll get around to fixing it properly one day!
-
Thanks, Theo. Could it do any harm if I keep playing it to see if it resolves on its own?
No it won't do any harm to keep playing, and see the advice from Rees above.
-
That's good. I will give Rees's tip a try. Thanks both.
-
I had a similar problem with my Piroulet, about 3 or 4 months after i bought it. The fettler i took it gave me a remarkable impression of a sharp intake of breath. He put a subsntial effort into trying to extract the rod with zero success. In the end he resorted to applying heat, to try and release it, by means of connecting the terminals of a car battery across it. He never did get the rod free, but the key did stop sticking. He returned it to me with reservations, working fine, but with a question mark hanging over the success of the repair.
It worked fine for a year (November to November) then it stuck again. My man was busy, but I arranged to take it to him after Christmas. This wasn't a big problem, because it was the second button down on the G row and I didn't need it much, where it did i could frig my way round it (mostly). The thing is, after about a week, it put itself right and the problem never came back in years of playing (I can't remember how many. 5? 6? 7?).
I'm not sure what the moral is of this story, or there even is one, but that's my experience.
-
Thanks Greg. I am hoping mine will also just heal itself.
-
I wonder if anyone else has experience of the car battery trick? It was exciting to see.
-
I wonder if anyone else has experience of the car battery trick? It was exciting to see.
Do you get smoke signals when it is complete? ;D
I had a number of sticking (wooden lever) keys on a one row I lent to someone, and I think that was down to it being kept in the garage, (He isn't a natural musician so he and/or the melodeon may have been banished to the garage) . I think Rees is right about the benefits of warmer, drier conditions.
-
I did try the car battery method once but it was way too dangerous to repeat - that Oakwood was smoking, man!
I think it would be less scary if some kind of potentiometer were included in the circuit.
-
I wonder if anyone else has experience of the car battery trick? It was exciting to see.
Do you get smoke signals when it is complete? ;D
I had a number of sticking (wooden lever) keys on a one row I lent to someone, and I think that was down to it being kept in the garage, (He isn't a natural musician so he and/or the melodeon may have been banished to the garage) . I think Rees is right about the benefits of warmer, drier conditions.
I did try the car battery method once but it was way too dangerous to repeat - that Oakwood was smoking, man!
I think it would be less scary if some kind of potentiometer were included in the circuit.
;D ;D ;D
I expect the continued good performance is due to the improved conditions.
It didn't smoke much and no scarring resulted, though there was a bit of scaring.
-
Rees and Theo will probably be aghast at the idea, but would silicon spray or locksmith graphite help?
-
Graphite won’t do any harm and might help. Any liquid will only make things worse by allowing dust to stick and build up.
In the end you have to get to the root of the problem and put it right.
-
If it’s absorbed some moisture, a hairdryer will help to warm it up. This is a trick that’s worked for me once or twice.
-
Thanks, Rog. I can't think how it could have absorbed any moisture as it is kept and played in the house.
-
If it’s absorbed some moisture, a hairdryer will help to warm it up. This is a trick that’s worked for me once or twice.
Glad that worked for you and probably a good method if you dry it off immediately. If the water has had time to be absorbed into the wood then it would've better to slowly dry out by just leaving it out of its case and at normal room temperature.
Thanks, Rog. I can't think how it could have absorbed any moisture as it is kept and played in the house.
It's not just about adding moisture. Any change in humidity, either getting more or less humid affects wood, and a change in either direction can cause wood to move. By any chance did the problem start around the time of the spell of very cold weather in early December? If so it could be the result of lower humidity. It's still the same solution - leave it at normal room temperature to come back to equilibrium.
-
... By any chance did the problem start around the time of the spell of very cold weather in early December? If so it could be the result of lower humidity. It's still the same solution - leave it at normal room temperature to come back to equilibrium.
That timing matches the problems I had.
-
Yesterday was the first time I had noticed the problem, and was surprised how it seemed to have happened overnight. At first I thought the reeds had stopped working but it was just that I had to press more firmly to open the valves.
-
I had this problem on a three voice Dino binci, Theo sorted it and the old rod felt rough to the touch. The short cuts mentioned are probably only delaying the inevitable!
-
" He put a subsntial effort into trying to extract the rod with zero success. In the end he resorted to applying heat, to try and release it, by means of connecting the terminals of a car battery across it."
I have done this quite a few times.Instruments with brass axels are harder since the brass is so conductive. You have to have cables that are a lot thicker than the axel.
i usually touch the axel for a second and wait a few seconds and repeat. This heats the axel evenly and you don't get hot spots. It it is really bad you may end up having to char things a bit to get it free. If so you will have to rebore to a larger size.
Once i get it to move I quickly chuck a drill to it and get it spinning to keep it from seizing (friction heats the tight spots) and draw it out.