Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Arnold on February 26, 2023, 05:35:07 PM
-
Hi, I’m currently tuning my 1040G. I’ve gapped the reeds, and revalved them, and I am now beginning to tune them inside the box. I am able to quickly open and close the box for tuning, since I am using slightly narrower nails in place of bellows pins for now, and the process is relatively straightforward. At the moment I am tuning the reeds which are just held in place by firmly positioned pins, and a couple of bits of blu tac either end to prevent slipping. My question is, when it comes to actually waxing the reedplates properly in place, will the pitch somehow be affected, and if so by how much and in which direction?.. thanks
-
If you're tuning them in the box, why not wax them in first before tuning?
-
So as to avoid the dreaded ‘Reed lifter’ lol. I tune all the push notes, make a note of how flat each of the pull notes are, then flip them and tune them the required number of cents as if they were push notes. Finally the reedplates are flipped one last time, then waxed. At least, that’s the plan!..
-
I think you might be better off tacking them in place with a dab of wax on each end ( forget the blue tape) get the reeds as close as possible then wax them in . And yes you may have some adjustments after.
I believe this is sort of how Theo does it, but don’t quote me!
-
Here’s a picture for clarity. I screwed a strip of wood in the middle to help support the reeds. Basically I am wondering whether the pitch I am getting from the reeds now will be the same as when I wax them in… I am changing to 2nd button start and spaces at button 1 and 10 are for accidentals and high notes in case anyone is wondering…
-
It won't be far different but it will be different.
Wax first and learn to use the lifter.
Worst case you'll clean off the reeds and do it again.
1040 is a nice box to start on, but the plane of the reeds makes some of the filing a bit awkward as you foul the casework .
-
Yes my advice is to learn to use a reed lifter. It’s not as difficult as it looks though I have to admit it is much easier to learn in person, than from printed instructions or even from videos.
You could also pretune slightly sharp, then wax in place then tune down to the target pitch which does not need a reed lifter, only a scratcher. You will still occasionally need to use a lifter for the times when you lower the pitch too much.
The biggest advantage of mastering the use of reed lifters is that it makes the whole process much quicker, and more accurate.
-
Ok thanks for the advice. I’d better check nothing is flat then get on with the waxing then!..
-
Quick question, I get a bit confused by all the talk about scrapers, drill bits, burrs, no burrs and so on. I have this Draper needle file. I think it’s good for filing reed tips up in pitch but wondering whether the tip is ok to scrape reeds down in pitch?.. I mean it makes a scratch but is it somehow the wrong type of scratch? Thanks for your patience!..
-
The tip of a file can be almost any shape so it would be hard to tell what angle to hold it at, and when you rotate it it might cut more or less deeply or not at all so you would never be able to develop a feel for how much the tool is cutting. And after some use how would you sharpen the cutting edge if you don't know what sort of edge it is?
You can make a good scratcher from an old file by first heating to cherry red then cooling slowly to soften the steel. Then file off the teeth for the end inch or two and shape it to be smooth round and gently gently tapered, and file at right angles to form a flat on the end. Then harden by heating to cherry red, quench in water, then sand the surface to remove the scale from heating and leave a bright surface, then temper to pale straw.
Or for the price of a file you can buy a scraper ready made that will last you years.
-
The other disadvantage of using a file is that it's a file so has abrasive edges. You can cause damage to the sides of the opening in the reedplate.
-
Nice one, thanks for all the info. I think I really should get a scratcher then and a lifter and so on!.. I was mainly concerned I might have damaged the reeds but I think they’re alright… I notice CGM has different diameter scratchers. I’m guessing 1.4mm for an ‘all rounder’?..
-
I get confused between a lifter and a hook. I use a u shaped hook make from piano wire (you can get them from Charlie….but I made one with a slightly smaller radius). For a 1050 though it can be tricky to lift the reeds coz they are flat down inside the casing. I think I normally manage ok with the bigger reeds but tack the little ones in (with blobs of wax) and pop them out to adjust. The issue I encounter on a box with flat mounted reeds is, if you aren’t careful, flattening inside reeds can mess up the reed gap (pushing it too wide when scraping the waist of the reed..if you don’t support it…or putting a curve in the reed if you do support it…nb..with practice this is avoided..but you need a v sharp scraper and then sort of stroke/scratch the reed with it rather than trying to put a score in the metal). And this seems to be a fault I encounter quite a lot, where someone has fettled a box but failed to optimise the reed performance …or pushed the reed tip which slows the response. Anyway, it’s something to look out for. If the reed is slow to speak check the gap, and pop it off and adjust it.
-
Thanks for all your thoughts and advice. For a start I will be getting the 1.4mm (I think) reed scraper from CGM. I’ll report back when I have made further progress!..
-
There seems to be rust on several of your reeds. You must remove it before doing any tuning.
-
What to you use to remove rust? I’ve scraped off powdery stuff before but this is a bit more set in…Thanks
-
What to you use to remove rust? I’ve scraped off powdery stuff before but this is a bit more set in…Thanks
https://www.axminstertools.com/axminster-detail-sanding-pen-kit-410218
-
Nice! What’s the cheapskate alternative? ;D I’ve just made a scraper out of an old 1.4mm drill bit and electrician tape, so I know there’s probably one out there!..
-
Nice! What’s the cheapskate alternative? ;D I’ve just made a scraper out of an old 1.4mm drill bit and electrician tape, so I know there’s probably one out there!..
Go to starbucks and half inch a load of coffee stirrers, pva some 400 grit abrasive paper to one end
-
I use very fine wire wool.
Slip a bit of flattened bean tin under to support the tongue.
I've tried all sorts and at the moment this is my favourite. But I use the shopvac a lot before I move on to something else.
-
Nice! What’s the cheapskate alternative? ;D I’ve just made a scraper out of an old 1.4mm drill bit and electrician tape, so I know there’s probably one out there!..
Go to starbucks and half inch a load of coffee stirrers, pva some 400 grit abrasive paper to one end
A bit upmarket. It will have to be Wetherspoons where I’ll be less conspicuous 8)
-
"What’s the cheapskate alternative?"
A man after my own heart! Firstly, get a daughter with a beauty salon. Secondly, call in on the premise of just saying hello, and maybe grabbing a cup of tea or coffee. Third, on the way out, cadge a few nail buffing thingies! They're four sided quite firm foam, about 3/4" wide and maybe 3 1/2" or 4" long with abrasive (pretty fine, but I don't know the grade) on all four sides. I find these ideal for the front face of the reeds. (10 for £3.49)
https://www.ebay.co.uk/itm/174867972112? (https://www.ebay.co.uk/itm/174867972112?)
Of course, you cannot fit them into the slots to do the back of the tongues. But I've found that usually I can get most of that off with a piece of wet and dry under the tongue or a small flat bladed screwdriver down the slot, and at the worst, a little strip of the wet and dry glued onto a divided up lolly stick. Although it seems to be quite common to pick these up from Starbucks or somewhere, I do prefer to get them via eBay where they can be had in different thicknesses and widths for not a lot of money.
-
Had a bit of a brainstorm walking home from work. Thank me later ;D: Magic Eraser!
Skip to 4:40 for use to remove rust: https://m.youtube.com/watch?v=y4F200dfBE0
-
If you remember the ink rubber from distant schooldays they are good rust removers, or if you can't find one then a polishing block.
-
Yep. On reflection perhaps the magic eraser isn’t quite the ticket since it leaves sponge dust everywhere. Perhaps prior to valving etc it might be good. But the job is done now at least!..
-
Abrasive rubber block is one way to clean reeds. Garryson (Garryflex) do them (120 grit) on eBay. Normally I get the little ones but the big ones can be cut up into eraser sized chunks (if you order the wrong size, as I did recently).