Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Torsten Feurstein on April 12, 2023, 09:22:05 PM

Title: Getting Preciosa buttons back in the fingerboard
Post by: Torsten Feurstein on April 12, 2023, 09:22:05 PM
I recently bought a Hohner Preciosa Eb/Bb that doesn't have the usual extra four club buttons on the third row. Trying to figure out if the box was factory converted  I removed the fingerboard to have a look. Unfortunately, now I cannot get the buttons back in the holes of the fingerboard, because of how the buttons attach to the levers. Any advice as to how to align the buttons so that I can get the fingerboard back in place?

Ps. I believe it was factory converted. Fingerboard look original, pallets and mechanism for the third row is all there. Missing four sets of reeds and no sign of wax where they should have been.
Title: Re: Getting Preciosa buttons back in the fingerboard
Post by: Theo on April 12, 2023, 09:56:55 PM
Some were made that way.  I have one too.

Best way to get the buttons back is to hold the keyboard with the buttons hanging down then bring the top up starting towards one end.  You are unlike to get all the buttons on straight away, but once you have a start you can use a hook to manipulate the buttons into place one at a time.
Title: Re: Getting Preciosa buttons back in the fingerboard
Post by: Lester on April 13, 2023, 07:24:05 AM
The way I do it is to remove the thumb board this gives you access to the button rods which I align using a set of needle nosed pliers starting withe the row nearest the bellows.
Title: Re: Getting Preciosa buttons back in the fingerboard
Post by: Torsten Feurstein on April 13, 2023, 10:58:38 AM
Thanks!
I was hesitant about removing more parts as I already made at mess of it. But I'll remove the thumb board and have a go.
Title: Re: Getting Preciosa buttons back in the fingerboard
Post by: Theo on April 13, 2023, 11:06:23 AM
I was assuming you had already removed the thumb board.
Title: Re: Getting Preciosa buttons back in the fingerboard
Post by: folkloristmark on April 13, 2023, 07:09:09 PM
They did make two rows the buttons wont be there but on the two row liliputs I have the reed blocks are the same ust have spaces no additional reeds.Interesting to see how that sits in The precy as it usaully has the flat block on top .
Title: Re: Getting Preciosa buttons back in the fingerboard
Post by: folkloristmark on April 13, 2023, 07:12:23 PM
Ps if you remove the top finger board it can be a real rollercoaster putting it back because of the hinged wire buttons. If its just a looksy remove the frontthumb board two or four screws its easier .You may already have found out the hard way. ??
Title: Re: Getting Preciosa buttons back in the fingerboard
Post by: folkloristmark on April 13, 2023, 07:16:48 PM
Bit confused if you want to put the top fingerboard back on the best way is to start form one end with it raised and push the buttons under the holes as you go along using the board to hold them first then slip them back with something like a screw driver or kitchen knife as you work your way to the other end the board lowers as each pair of buttons falls into place.Thats my way it can take quite a time at first as if buttons fall out of holes you need to start again can be done
Title: Re: Getting Preciosa buttons back in the fingerboard
Post by: Torsten Feurstein on April 14, 2023, 08:27:26 AM
Thanks for all the help!
Buttons back in place by removing the thumb board, some pliers, and some foul language.
Nice little box. Needs tuning/revalve at some point, but still playable.  It makes my standard sized Maugein two row look like a giant.


SimplePortal 2.3.5 © 2008-2012, SimplePortal