Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Pat McInnis on March 23, 2024, 06:55:27 PM

Title: Back to Bellows
Post by: Pat McInnis on March 23, 2024, 06:55:27 PM
I know this is my second leaky bellows post but the thread by Disparate Dan had me out to the shop to see what I could do to chase down my own leaky bellows. The suggestion of using an old stethoscope was a great idea. I had one and just took the end off so I had a rubber line that I could chase potential leak spots while cycling the bellows or working the treble and bass ends on my tuning bellows since it gave me a free hand. I found a few small leaks around the bellows gasket and one misaligned treble pallet. Fixed. The AH Ha moment came when I took the bellows into a dark corner and shone a flashlight from the inside out. the corners that flex between the cardboard folds are in terrible shape. Some just seem thin but there are also some pinholes that will definitely leak enough air to make playing difficult. I'd rather not junk the bellows after painting the outer folds and retaping, which is hugely labour intensive but I'm not sure that there is a repair that can flex with the corners. (https://live.staticflickr.com/65535/53606522800_34d98e3540_c.jpg) (https://flic.kr/p/2pF2rB7)IMG_7285 (https://flic.kr/p/2pF2rB7) by Pat McInnis (https://www.flickr.com/photos/157073130@N07/), on Flickr
Title: Re: Back to Bellows
Post by: Disparate Dan on March 23, 2024, 07:23:46 PM
My favourite way of tracing elusive air leaks on reed organs is to watch the smoke from an incense stick held nearby.  Can't see why it wouldn't work just as well on box bellows, but if it doesn't, at least your house will smell pretty.
Title: Re: Back to Bellows
Post by: Peadar on March 23, 2024, 07:54:50 PM
I know this is my second leaky bellows post but the thread by Disparate Dan had me out to the shop to see what I could do to chase down my own leaky bellows. The suggestion of using an old stethoscope was a great idea. I had one and just took the end off so I had a rubber line that I could chase potential leak spots while cycling the bellows or working the treble and bass ends on my tuning bellows since it gave me a free hand. I found a few small leaks around the bellows gasket and one misaligned treble pallet. Fixed. The AH Ha moment came when I took the bellows into a dark corner and shone a flashlight from the inside out. the corners that flex between the cardboard folds are in terrible shape. Some just seem thin but there are also some pinholes that will definitely leak enough air to make playing difficult. I'd rather not junk the bellows after painting the outer folds and retaping, which is hugely labour intensive but I'm not sure that there is a repair that can flex with the corners. (https://live.staticflickr.com/65535/53606522800_34d98e3540_c.jpg) (https://flic.kr/p/2pF2rB7)IMG_7285 (https://flic.kr/p/2pF2rB7) by Pat McInnis (https://www.flickr.com/photos/157073130@N07/), on Flickr
Uuugh...
Maybe smearing a bit of rubber solution from a cycle puncture repair kit on the inside?....but even if it works it's on a par with the 19th century (locomotive) engine man putting a handfull of oatmeal into the boiler feed water to keep a leaking tube in the firebox going.
The right way of course is to dampen and peel back the bellows tapes and bellows papers then remove and renew the corner patch. I have done it - once - on a single failed corner patch. Not convinced I would fancy doing it on  the sixty odd patches of a fifteen fold bellows.
Title: Re: Back to Bellows
Post by: Pat McInnis on March 23, 2024, 07:56:07 PM
My favourite way of tracing elusive air leaks on reed organs is to watch the smoke from an incense stick held nearby.  Can't see why it wouldn't work just as well on box bellows, but if it doesn't, at least your house will smell pretty.

That's funny, I'm not a huge fan of insense but I've been thinking of ways to incorporate smoke into my leak detection.
Title: Re: Back to Bellows
Post by: Squeaky Pete on March 23, 2024, 09:13:07 PM
I have a club V from maybe the 50s when they were experimenting with using leather substitute corners that became quite porous.
I even sourced bellows of a close to similar size (Thanks Microbot) but as a last ditch attempt before making adaptors for the frames I thinned out some cheap PVA and put a couple of thin coats on the diamonds from the inside.
Astonishingly it worked rather well
Title: Re: Back to Bellows
Post by: Peadar on March 23, 2024, 09:48:44 PM
I have a club V from maybe the 50s when they were experimenting with using leather substitute corners that became quite porous.
I even sourced bellows of a close to similar size (Thanks Microbot) but as a last ditch attempt before making adaptors for the frames I thinned out some cheap PVA and put a couple of thin coats on the diamonds from the inside.
Astonishingly it worked rather well
That would work better than my suggestion....copydex might be an alternative as stays flexible but apparently has a short life then degrades..whether that is atmospheric oxidation or UV decomposition I don't know.
Title: Re: Back to Bellows
Post by: Pat McInnis on March 23, 2024, 10:00:30 PM
I have a club V from maybe the 50s when they were experimenting with using leather substitute corners that became quite porous.
I even sourced bellows of a close to similar size (Thanks Microbot) but as a last ditch attempt before making adaptors for the frames I thinned out some cheap PVA and put a couple of thin coats on the diamonds from the inside.
Astonishingly it worked rather well

Interesting stuff Pete, As you can see from my photo (hopefully), there are no diamonds over the inner corners. I wonder if there is a flexible enough material to use? Also, did you just thin the PVA with water? I'm determined to give this repair a go even if it fails. Nothing ventured...
Title: Re: Back to Bellows
Post by: Theo on March 23, 2024, 10:32:58 PM
It is possible to make a long term repair of leaking gussets by gluing a very thin layer of soft leather on the inside.  It does make the corner slightly thicker but with the right materials it will outlast the rest of the bellows.
Title: Re: Back to Bellows
Post by: Squeaky Pete on March 23, 2024, 11:13:51 PM
Pat, the diamonds are glued on the outside of the cardboard and what you see in your photos is exact what you'd expect to see of the diamonds.
I used a cheap PVA which is not waterproof (so not suitable for external joinery) and I had noticed it was more flexible whan set than the exterior stuff. Thinning it made it even easier to use. I had to stretch the bellows on a frame to keep the corners taut.
Title: Re: Back to Bellows
Post by: Ross Dubois on March 29, 2024, 12:15:09 AM
It is possible to make a long term repair of leaking gussets by gluing a very thin layer of soft leather on the inside.  It does make the corner slightly thicker but with the right materials it will outlast the rest of the bellows.

I've skivved down some very soft leather until it was shy of tissue thin and glued it over holes. Works a treat. I've done that sort of thing for concertina bellows repair for a number of years and none have failed or impeded the bellows function, aesthetically or mechanically... Yet.
SimplePortal 2.3.5 © 2008-2012, SimplePortal