Melodeon.net Forums
Discussions => Other Free Reed Instruments => Topic started by: Jack Humphreys on June 07, 2024, 09:18:27 AM
-
I know this isn't about a melodeon, but I'm hoping that someone can help.
On the box I'm trying to fix, I've removed the panel with all 72 holes in it. So now there are 72 buttons dangling randomly from their push rods. I've almost finished sorting them into their 6 ranks, kept apart with strips of card, and into their sequences. (Not fun).
But I don't know how to do the next step: How to replace the holey panel while guiding each button into its correct hole. I'm hoping that there is a trick to doing this which you can let me know about.
-
My usual method is to put the box upside down and wiggle the plate around until most of the buttons have found their place. The remaining ones can usually be guided into place with a needle through the hole, or with something long and that can get inbetween all the rods. That's what works for me, anyway!
-
I would just remove them one by one and then rebuild them one by one. Sounds like a lot of work but in the end might be easier and faster, and you're running lower risk of bending some of them from mis-alignment.
It's only a 72-bass anyway, now if you had a 180 bass, that would be a bit more of a challenge.
-
I would just remove them one by one and then rebuild them one by one. Sounds like a lot of work but in the end might be easier and faster, and you're running lower risk of bending some of them from mis-alignment.
It's only a 72-bass anyway, now if you had a 180 bass, that would be a bit more of a challenge.
Thanks for your suggestion M. Chavez! Sounds like you know about these machines. I don't quite understand what you mean by rebuild. How to rebuild is my problem.
I have all the buttons now arranged into ranks and sequences, but I don't know how to fit the holey plate back on while keeping the buttons in the right places.
-
My usual method is to put the box upside down and wiggle the plate around until most of the buttons have found their place. The remaining ones can usually be guided into place with a needle through the hole, or with something long and that can get inbetween all the rods. That's what works for me, anyway!
Thanks Squeezebox. Turning it upside down is a brilliant idea. Unfortunately, the buttons do not find their place! It's all so tiny that rows interfere with each other and don't hang together as a distinct row of similar chords or notes. I will still have to find a way of sorting out the diminished from the sevenths etc etc. But it looks like it will be much easier upside down rather than buttons up. At least the buttons want to point themselves in roughly the right direction thanks to gravity. Any more suggestions for helping with my 72 buttons would be most welcome.
-
Not the same job but similar
https://www.youtube.com/watch?v=p__2-_8Fk9M
-
I've rebuilt two stradellas and serviced one converter - won't say I know much about them, but in all cases the easiest solution was to disassemble the push rods one-by-one, and then remove the holey plate. It was the sliding design on all 3.
To put it back, push the holey plate in place, then assemble the bass machine push rods one by one (install a push rod & push it through it's hole one a time).
Try not to mix them up, because if you do, it's a job from hell to figure out where you've messed up. Don't ask me how I know it...
I don't play or fettle with accordion any more ;D
-
Not the same job but similar
https://www.youtube.com/watch?v=p__2-_8Fk9M
Thanks very much Lester,
I am struggling to do roughly what you show in the video. But when 72 buttons go "all flopperty" it's a nightmare to corral them into rows. They don't stay put when placed in rows, like your sturdy Hohner ones, but just keep flopping into the next row. I have to keep them apart with strips of cardboard.
Thanks especially for your recommendation for very long-nosed pliers, or that scissor-type gadget you used. And it makes obvious sense to start at the row which is furthest away.
I've been struggling with this for many hours, and maybe I can get somewhere now.
-
End of the story: I got so frustrated that I sent the accordion off to an expert, in this case Marcus Noon of Og accordions. It still took him three hours to get the **** buttons back in their proper holes.
Moral of the story: don't remove the button board unless absolutely necessary.
-
hi as already said stradella bass disassembly should be carried out by taking out each button and rod one by one starting from the left and put each layer /row of leavers in order on a tray left to right label each tray until all leavers are out of the case next you have all the long rods to take out but first mark them with a sharpie bothends with a different colour at an angle so they only go back one way also making notes and pictures as you take a part each layer on a diffrent tray and you cant go wrong i learnt this method when i was on a course in castelfidardo i hope it helps someone it took 7hours to complete 120 bass without replacing pallets or springs ect
-
I disassemble bass machines fairly frequently. There are several different constructions. The OP (it sounds like) BM is common to many Chinese PAs, where the mechanism lifts out, but removing the finger plate is a very bad idea, because as he discovered (it sounds like…but I might be wrong in his case) the buttons dangle and are tricky to get back. Another common problem is that the cassette mechanism comes loose and the buttons drop into the instrument. Generally it's not too difficult to fix (unless somebody has been bending stuff..then it can take longer…figuring out where to bend stuff back). I use a wire hook to move the buttons back.
The more traditional style of BM is easy to disassemble. Laying the levers out on a tray is actually a recipe for disaster. What you need is a rack, made from a couple of old 120 fingerboards, or drilled or whatever. Then remove the buttons and put them in their position in the rack. The Accordion Maintenance Manual book by Reuther shows this technique. The pipes are laid out on a tray. There are other BM constructions that are trickier to work on. Scandalli is an example, where the pistons are held in place with rubber/plastic tubing. I tend to avoid these, but don't see them very often (thankfully). Hohner BMs are quite nice because they come out in a big cassette like assemble, but old ones are prone to stick where white corrosion occurs, can can be difficult to get working properly. Bayan bass machines may or may not be maintence friendly..it depends…