Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: dino.pafftti on April 03, 2025, 09:40:58 AM

Title: Hohner Corso proplem
Post by: dino.pafftti on April 03, 2025, 09:40:58 AM
Big problem in Corso,
I noticed that air was leaking from under the reed block. Reed block is straight, But the lid seems to be convex ,,
gap about 0.6 -0.7mm,,    Can the lid be straightened, or a thicker gasket be installed? Good advice is needed,,  :-[
Title: Re: Hohner Corso proplem
Post by: dino.pafftti on April 03, 2025, 10:06:35 AM
only the fingerboard side reed block leaks, the others are tight
Title: Re: Hohner Corso proplem
Post by: Theo on April 03, 2025, 10:22:14 AM
I’ve develop a fix for this on Club 2/Erika.  It might or might not work on Corso with three blocks instead of two. Are all three blocks affected?

I’ll find some photos of what I’ve done.
Title: Re: Hohner Corso proplem
Post by: dino.pafftti on April 03, 2025, 10:26:28 AM
Endast ett block läcker
Title: Re: Hohner Corso proplem
Post by: dino.pafftti on April 03, 2025, 10:31:07 AM
I’ve develop a fix for this on Club 2/Erika.  It might or might not work on Corso with three blocks instead of two. Are all three blocks affected?

I’ll find some photos of what I’ve done.

only one block is leaking
Title: Re: Hohner Corso proplem
Post by: Theo on April 03, 2025, 10:58:47 AM
Here is a photo of an old example of how I fix the warped fondo.   You can see the bracing rib attached beside the the reed block.  There is another out of sight beyond the reed blocks.  I've removed the normal reed block locating blocks. The rib is screwed in place from the pallet side.  The rib is carefully shaped with a concave surface so that as the screws are tightened the rib and the fondo pull together just enough to get the fondo perfectly flat.  It takes a bit of trial and error to balance the stiffness of the rib and the degree of curvature to give you the flat fondo.  The rib in the picture is also glued in place after all the adjustments have been made.
Title: Re: Hohner Corso proplem
Post by: dino.pafftti on April 03, 2025, 11:09:36 AM
Ok,, Thanks, I was thinking something like this too, I need to get some hard wood from the carpenter  (:)
Title: Re: Hohner Corso proplem
Post by: Theo on April 03, 2025, 11:50:07 AM
I’ve used beech or maple.
Title: Re: Hohner Corso proplem
Post by: dino.pafftti on April 03, 2025, 03:37:19 PM
 (:) Ok...
Title: Re: Hohner Corso proplem
Post by: Winston Smith on April 03, 2025, 04:49:47 PM
I had the same problem with my Busillachio, and followed Theo's advice. Not knowing about wood (to me a hardwood was keruing, which we used for wagon body floors in the old days) I used a bit of 9 ply 3/4 plywood as a stiffener. It has worked fine, so far!
Good luck with your box.
Title: Re: Hohner Corso proplem
Post by: mChavez on April 03, 2025, 05:08:58 PM
When I had this problem on my Shuya, I just replaced the fondo with a new one.  >:E
But I've seen thick window insulation tape being used to fix an issue like this.
Title: Re: Hohner Corso proplem
Post by: hickory-wind on April 03, 2025, 07:18:14 PM
Another method is to mill or router the reedblock contact area flat then add a new closed foam gasket in the shallow 'pocket'. It is perhaps more effort than other methods but results were excellent.


Scott
Title: Re: Hohner Corso proplem
Post by: dino.pafftti on April 04, 2025, 05:06:16 PM
I had the same problem with my Busillachio, and followed Theo's advice. Not knowing about wood (to me a hardwood was keruing, which we used for wagon body floors in the old days) I used a bit of 9 ply 3/4 plywood as a stiffener. It has worked fine, so far!
Good luck with your box.

I think Theo's advice is good.  (:) :|||:
SimplePortal 2.3.5 © 2008-2012, SimplePortal