Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Fanie on April 05, 2025, 11:47:36 AM
-
I repaired the wooden keyboard on my Erica.
-
2
-
3
-
That would seem to be an Erica?
-
:-\
Yes, sorry, I got mixed up. Its an Erica
-
Nice work! I’ve thought about doing this on a few occasions. Btw, what kind of glue is it that you used? It doesn’t look like wood glue.
-
I used super glue and then put bicarbonate of soda over it to fill the gaps.
-
That definitely took some time. Nice one. I've done many similar button board repairs before we just started making new ones.
-
"just started making new ones."
Interesting!
-
Looks good!
Another way to repair them is to router out the face as shown in my photo and then
make a new plate. This way it is removable for padding the buttons or other adjustments.
I used the tick marks on the bottom of the original fingerboard for the holes.
I also did one on a box with the presswood decoration at the bottom of the keyboard where I left the decoration at the bottom so basically the new plate didn’t go all the way down.
I used a jig to make the cutout in the keyboard and it also held the keyboard tight in the jig so there was no moving around during the cutting process. The new plate was just fitted and then drilled out on my drill press.
Picture doesn’t show the screws that I installed later to hold the plate in place.
-
I have developed an alternative to repairs or full replacement of broken Hohner keyboard tops that maintains the original wood. It is a similar approach to Boxcall's, above. It is a flat machined panel with 21 slots (not holes but slots like the original) and 4 countersunk screw holes. I made a milling fixture to hold either 1/8" thick or 1/16" thick aluminum extrusions by the edges. A large CNC machine was used for accurate repeatable machining. A special round-over bit was purchased to put a small radius on the full perimeter of each slot and also on the machined ends of the extrusion. The extruding process itself provides a small radius on the long edges. This radius provides a nice comfortable edge so the fingers aren't going across a sharp corner.
It is discussed in detail here with photos:
https://forum.melodeon.net/index.php?topic=25858.msg308136#msg308136
With all the design time, fabrication, material and fixtures I am asking for $45 plus shipping. The first few folks can get one for $40 if you provide feedback to me on your installation experience.
Scott
-
I have developed an alternative to repairs or full replacement of broken Hohner keyboard tops that maintains the original wood. It is a similar approach to Boxcall's, above. It is a flat machined panel with 21 slots (not holes but slots like the original) and 4 countersunk screw holes. I made a milling fixture to hold either 1/8" thick or 1/16" thick aluminum extrusions by the edges. A large CNC machine was used for accurate repeatable machining. A special round-over bit was purchased to put a small radius on the full perimeter of each slot and also on the machined ends of the extrusion. The extruding process itself provides a small radius on the long edges. This radius provides a nice comfortable edge so the fingers aren't going across a sharp corner.
It is discussed in detail here with photos:
https://forum.melodeon.net/index.php?topic=25858.msg308136#msg308136
With all the design time, fabrication, material and fixtures I am asking for $45 plus shipping. The first few folks can get one for $40 if you provide feedback to me on your installation experience.
Scott
I believe I developed this method first or at least on a one row ( which could easily be applied to a two row). my project was presented here before you showed us your method, although I do believe that the use of metal is a good one and your method. I just used wood for it was available and easy to fit.
As for slots instead of holes are you referring to elongated holes? Because that is how I did mine to match the original holes ( which are elongated or oval shaped holes ). My method only requires a router and a piece of plywood with a square hole cut out to match the size of the repair and a little bit of woodworking skill. And then a drill press it is quite easy to cut the holes using a fence then shim the piece away from the fence and elongate the holes. I believe we have the same system and results but with different materials and tools being used.
-
I believe I developed this method first or at least on a one row ( which could easily be applied to a two row). my project was presented here before you showed us your method, although I do believe that the use of metal is a good one and your method. I just used wood for it was available and easy to fit.
I suspect this method has been independently developed by many people.
-
I believe I developed this method first or at least on a one row ( which could easily be applied to a two row). my project was presented here before you showed us your method, although I do believe that the use of metal is a good one and your method. I just used wood for it was available and easy to fit.
I suspect this method has been independently developed by many people.
I’m sure that’s true Theo, but I didn’t see the method used or posted here prior to my post, I may have missed it if it was. In any case I am not looking to make it mine, I’m just saying it was done before so not a new method.
-
Actually Hohner were using removable metal plates on their keyboards way back when in the 1930s as can be seen on this 3515:
http://forum.melodeon.net/index.php?topic=19800.msg239476#msg239476 (http://forum.melodeon.net/index.php?topic=19800.msg239476#msg239476)
And here is a link to an earlier thread where I had done a keyboard patching job of the same type as Fanie's. I guess the extent of the damage and the desire to keep the character of the box are factors when choosing a repair method.
http://forum.melodeon.net/index.php?topic=21122.msg258493#msg258493 (http://forum.melodeon.net/index.php?topic=21122.msg258493#msg258493)