Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: robinbid on April 21, 2025, 04:17:10 PM

Title: Coil springs for Cajun accordion
Post by: robinbid on April 21, 2025, 04:17:10 PM
Can anyone point me in the direction of a source for 7mm coil springs for my keyboard? 24 years old and starting to leak air, the box that is…. Have tried searching online but not much joy. Any help appreciated.
Title: Re: Coil springs for Cajun accordion
Post by: Theo on April 21, 2025, 04:20:52 PM
I don’t know a source for springs, but there are more likely sources of air leaks than weak springs.
Title: Re: Coil springs for Cajun accordion
Post by: tirpous on April 21, 2025, 04:50:04 PM
Coil springs can be found on eBay, often stainless steel and from China. You may need more specific details about your required spring. Presumably 7mm is coil length, but what about coil diameter and wire size ?? Note it's possible to purchase a long coil and cut it in shorter lengths, which can be convenient if you want to experiment with different tensions.

Try a search with 'small stainless steel extension coil spring' or something like that.

But as Theo said, maybe your problem is elsewhere anyway.
Title: Re: Coil springs for Cajun accordion
Post by: rees on April 21, 2025, 05:05:29 PM
You can shorten the existing springs to give more pressure at the pallets. This will also give a slightly heavier action at the buttons. Longer springs give a lighter action but can cause air leaks at the pallets. There's a fine balance between action and pallet pressure, finding the right spring is a matter of trial and error.
To shorten a spring by one coil, first snip the loop off one end.
To create a new loop, place two thin knife blades between the first and second coil.
Push one blade back towards the coil and bring the other blade flat to the bench.
This is a one way process, you can't make the spring longer again!
Title: Re: Coil springs for Cajun accordion
Post by: mChavez on April 21, 2025, 05:16:35 PM
This is a one way process, you can't make the spring longer again!

Lightly stretch it open?
Title: Re: Coil springs for Cajun accordion
Post by: rees on April 21, 2025, 06:35:36 PM
This is a one way process, you can't make the spring longer again!

Lightly stretch it open?

Yes, there is that. Or jam a screwdriver between the coils and twist (as I was shown by a respected old-timer accordion maker in Louisiana).
He also used a hot soldering iron on the centre of the spring to soften the temper so weakening the spring. A bit hit and miss!
The screwdriver method is brutal but more accurate.
Title: Re: Coil springs for Cajun accordion
Post by: robinbid on April 22, 2025, 08:32:49 AM
Have found a set of 10 on Accordionshop24 in Germany.
Title: Re: Coil springs for Cajun accordion
Post by: rees on April 22, 2025, 12:04:45 PM
Hi Robin. Let us know how those springs work out.
Title: Re: Coil springs for Cajun accordion
Post by: mselic on April 22, 2025, 03:04:48 PM
The problem with buying coil springs that have already been cut to size is that they are very rarely ready-to-go when installed in a particular instrument. They will almost certainly require adjusting, shortening, etc but there is also a limit to how much a pre-cut length of coil can be adjusted.  In Cajun boxes, the coil springs span two nails, one of which is in the lever and the other on another part of the keyboard itself (I’ve even seen the other nail in the pallet itself!!) The distance between these nails is different on every instrument, and even within the same instrument, so they need to be adjusted to get the appropriate amount of tension. It’s for this reason that I’ve found the best bet is to buy longer lengths of coils (of different gauges, coil size, etc) and then just cut off lengths yourself as described by others earlier in this thread. I’ve done extensive work with making, adjusting and replacing coil-springs for Cajun-style boxes, so I know from personal experience it’s rarely as simple as buying a set of accordion coil springs and just swapping out the old ones.
Title: Re: Coil springs for Cajun accordion
Post by: robinbid on April 25, 2025, 04:18:44 PM
http://www.accordionshop24.com/treble-spiral-spring-for-accordion-oe5x7mm.html

Yes, you’re right. The nails are too close together and the new springs are just not under enough tension. Thanks to Rees’s tip with the razor blades, I have shortened the original springs and now have a box which is airtight on the push. Have found other issues with a couple of reeds, but that’s for another day. Thanks for the helpful advice.
SimplePortal 2.3.5 © 2008-2012, SimplePortal