Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Lew Morris on December 23, 2025, 10:47:36 PM

Title: Shoulder strap bracket - screw length?
Post by: Lew Morris on December 23, 2025, 10:47:36 PM
I finally got my Levy shoulder straps, and the V-brackets, so it's time to fit the brackets onto my Hohner 2815.

Lester's video revealed that I wouldn't hit anything vital, but left out screw size, and length information.

The brackets that I have do not have countersunk holes (the stamped base material is thin), so I will need to use round head screws.

#2 seems to small, and #4 seems like overkill

Length; my guess would be 3/8" [10mm]

Surprisingly, I couldn't find anything small enough at my local hardware store, so I'll have to order them.




Title: Re: Shoulder strap bracket - screw length?
Post by: mChavez on December 24, 2025, 07:43:23 AM
fwiw, I use similar brackets and I ream mine out + lightly countersink them to take the most aggressive wood screw I can find. I don't want a tiny screws pulling out and messing up the holes.

For the length, I just open the box and see what will work and what won't.
Title: Re: Shoulder strap bracket - screw length?
Post by: Lew Morris on January 03, 2026, 11:58:35 PM
Ref. for anyone else.

#3 x 3/8" [9.5mm] worked out just right.

#3 seems to be an oddball size (#2 and #4 are more common), I found them at a guitar store (used to mounting the tuning capstans)
Title: Re: Shoulder strap bracket - screw length?
Post by: Lew Morris on January 07, 2026, 09:08:21 PM


I mounted the lower strap bracket on the "bottom" end. Single strap playing; no problems.  But two minutes of playing, with two straps, immediately revealed that this was mistake; the bottom left-side strap drags on the bellows.

Perhaps I should have mounted the lower bracket on the lower edge of the bass end of the box.

Time to figure out how to plug the three holes, in something like a workmanlike manner.

The best laid plans.. .. 
Title: Re: Shoulder strap bracket - screw length?
Post by: squeezy on January 17, 2026, 01:14:45 AM
This is not "a mistake" ... 99% of melodeons I have ever seen from every manufacturer have strap brackets in the position you show.

I have seen and played some unusual instruments with the alternative you circle in red and I have to say that the balance of the instrument in those cases made the angle and position of the instruments more awkward to play.

I don't know of a strap system which doesn't come in contact with the bellows of the instrument.
Title: Re: Shoulder strap bracket - screw length?
Post by: mChavez on January 17, 2026, 08:18:47 AM
A lot of accordions (PAs and CBAs) have the bracket in the circled position. That's where I put mine on hromkas too.
Never noticed any balancing problems.

PS them tiny screws for mounting guitar tuners are not designed to take any load and I personally wouldn't trust them to hold down a strap bracket.
Title: Re: Shoulder strap bracket - screw length?
Post by: Steve C. on January 17, 2026, 11:41:02 AM
Don't do it Lew.
The angle of tension will pull the bracket right out. Ugly.
And what Chavez sez: need more aggressive screws. You probably have room for #4 1/2" round head wood screws which are readily available.
Title: Re: Shoulder strap bracket - screw length?
Post by: mChavez on January 18, 2026, 08:50:28 AM
What I use for guitar tuners vs what I use for strap brackets  8)

SimplePortal 2.3.5 © 2008-2012, SimplePortal