Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Stiamh on March 16, 2010, 05:44:56 PM
-
I have to tape off the thirds in a student's Erica and want to perform the spaying operation in about 10 or 15 minutes before a class later this week.
I remember reading that doing this on a Hohner Black Dot or Erica is not as straightforward as on models by other makers because the thirds aren't in a nice straight line on the reedblocks. Not having an Erica lying around the house I was wondering if anybody can give me some pointers to locating the thirds quickly.
Merci d'avance
-
I'm not sure if they are the same as on my Pokerwork, but I mapped out where the various reeds were when I took the thirds out of mine. I can email you the word document if you want.
-
Whoa, that was quick. Yes please!
-
Sent! (:) :||:
-
Thanks. But cripes. Your diagram shows that the thirds aren't back to back - in other words you can't just block off one hole with tape and knock out the push and pull thirds. How did you do it, then? Tape up each reed, somehow?
-
You can only do what on suggest on the C chord, all the others I just (and this probably isn't a great thing to do, but it works) was slot a piece of paper under the reed to stop it vibrating.
-
Many thanks for the help, Ollie. Unfortunately on the Erica I'll be doctoring none of the chords are the same push and pull. Now I understand why the process was said to be less straightforward than it might be!
And if anyone else has any pet remedies, do chime in...
-
I prefer to use Scotch Magic Tape (http://www.scotchbrand.com/wps/portal/3M/en_US/ScotchBrand/Scotch/Products/ProductCatalog/?PC_7_RJH9U52300LM30I87QR3ES18H7_nid=3SW92B74ZVgsTF1RRQ4PQRglLJW3QDKQH0bl) because it can be removed after a long period of time and leaves almost no sticky residue.
For the push reeds I stick the tape lengthways over the reed tongue. For the pull reeds I lift the valve and place the tape along the full length of the slot, under the valve. This is a bit fiddly and needs more than two hands.
-
Thanks Theo. I have a roll of that stuff in my desk drawer.
I'm having a bet with myself just now on whether I'll get the job done in 10 minutes, and I have a nasty premonition that I'm going to lose.
-
I'm betting against you ;D :o
-
I had a Erika which took 2 hours, four hands, 2 pairs of pliers, a vice and a soldering iron just to get the bellows pins out... but hopefully yours will be quicker!
-
I had a Erika which took 2 hours, four hands, 2 pairs of pliers, a vice and a soldering iron just to get the bellows pins out...
Sounds just like my Erika, I used a pair of fretwire cuttters that allowed me to get a good grip underneath the pin head and they only took a couple of minutes...after 40 minutes of struggling with pliers. ::)
-
I had a Erika which took 2 hours, four hands, 2 pairs of pliers, a vice and a soldering iron just to get the bellows pins out... but hopefully yours will be quicker!
It has screws. Ask Pip Ives!
-
"... I used a pair of fretwire cuttters that allowed me to get a good grip underneath the pin head....." :o Reminds me of a pal who's mother used his purfling chisel to open a tin of paint! Tut tut!!! T.
-
's OK, they've served with distinction but are now a bit dull and not quite up to cutting flush anymore. They've now been given a second chance as bellows pin pullers. ;D
-
Challenge or opportunity? I count myself lucky as my pocket knife has a fork-ended thingee, so blunt it doesn't mark the box when I lever the pins out. I'm pretty sure it wouldn't do whatever it was supposed to, though...
Rob.
-
I had a Erika which took 2 hours, four hands, 2 pairs of pliers, a vice and a soldering iron just to get the bellows pins out... but hopefully yours will be quicker!
It could be worse mine work their way out all the time and having tried several methods are now held in with a fine strand from soft string, must get new pins do a propper repair at some point.
-
I use a pair of joiners /cabinet makers pincers to pull the pins as they fit firmly round the pin & enable a straight pull rather than a leavering action much the same as a dentist pulling teeth. As far as loose pins I have on a number of occasions inserted a sliver of wood shaved off a matchstick down the pin hole as a temporary measure & its been a very long lasting temporary measure!
george
-
My missus wonders why her nail clippers are buggered!