Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Pete Dunk on March 27, 2008, 06:58:11 PM

Title: Re-taping Bellows
Post by: Pete Dunk on March 27, 2008, 06:58:11 PM
I have a 1930's or so three voice, two row Hohner with 20 fold bellows that need retaping. The back and the bottom are the bad bits but I don't like doing half a job so I thought I'd do the lot which involves some 24.6 meters of tape. What I don't know is what's involved in carrying out the work and what the potential pitfalls (if any) are.

Is striping off the old tape tricky or likely to cause damage to the bellows cards? What kind of adhesive is used to glue on the new tape and how quickly does it dry?

Any hints or tips about doing the job and sources of materials greatly appreciated.

Pete.
Title: Re: Re-taping Bellows
Post by: Quebecois on March 27, 2008, 07:58:07 PM
I replaced the bottom-side tape on my Corona following instructions found on Bernard Loffet's  help pages (http://diato.org/trucs/soufflet.htm#1)  (they are in French! but there are a few pics).

It's not difficult, but it takes time and patience and it's precision work. Removing the old tape can be tricky, you don't want to damage the bellows by doing so, it also depends on what type of glue they used when installing the original tape.

Each tape strip must be cut to the same exact length and carefully installed so all ends are aligned on a straight line and the tape strips are centered. If using tape with a moiré effect all strips must be installed following the same direction. When applying a strip of tape, you need to make sure it is properly affixed and centered, then close the bellows to keep it in place while you get the next strip ready. The first one is easy to install, but it gets tricky from the second one on! Take your time. It's easier if you fold the tape before glueing. If there is any excess glue wipe it off with a paper towel or clean rag.

I used simple white glue, as suggested by Bernard. He mentions that you need about 17 metres of tape for a typical Pokerwork-size bellows.

Title: Re: Re-taping Bellows
Post by: suesqueezer on March 27, 2008, 08:39:01 PM

As mentioned, cut exactly the same size lengths for the sides as needed first. Make sure you have a clean edge by removing old tape first - if ya lay it on top it's adding to the thickness overall and where is was loose and worn will just create a bad adhesion. The trick to working with each piece of tape is all in the glue. Get yourself of piece of glass or a plastic rigid sheet, and apply the glue to this by using a piece of cardboard and trowelling it into an even patch of glue maybe 1/32 inch thick and as wide as 3 pieces of tape width, then I lay my pieces of tape onto the surface, so you are covering the bottom of tape pieces fairly evenly - just touch em down with your finger a bit. Then I lift em off and set aside - you will see that only a textured amount went on the backs this way. In case there's misses on the backs just touch up with more glue.  THE KEY NOW IS "TACKING UP" OF GLUE. It's good to let the glue sort of dry up a bit. Then get some clothespins or cotton balls and put them in each of bellows so the one you are taping is sort of on its own. Then lay down a glue covered piece as best as you can centred on width and length and squish down & adjust - it will still be a bit moveable and this way very little excess glue. Have a wet damp rag on hand to smooth over the applied tape and any excess glue removed. After you do a side, cut some pieces of wax paper and stick inbetween each bellow and put some weight on the whole bellows to really set. I use WeldBond glue which is a white glue and drys clear.
Title: Re: Re-taping Bellows
Post by: Pete Dunk on March 27, 2008, 10:21:12 PM
Thanks for the helpful comments, I'm fairly used to working with the leather top runs on concertina bellows and found out by trial and error that rebinding over existing leather gives far too much bulk to the finished bellows and soaking too much to get the old stuff off leaves you with a pile of useless parts!

In normal circumstances I would have gone for PVA (white glue, Elmer's, call it what you will) but I wasn't sure that would work where the tape overlaps the metal corners. I wasn't sure either if there was any stretch in the tape bindings but the advice to cut precisely to length beforehand suggests not. So do I just carefully remove the old tape dry or will damping down first help (or indeed cause a disaster)?
Title: Re: Re-taping Bellows
Post by: Theo on March 27, 2008, 11:18:13 PM
Just remove the old tape dry.  Carefully lift one end and it should pull off in one piece.  You might want to scrape off loose material left behind.  The tape is not significantly stretchable.
Title: Re: Re-taping Bellows
Post by: Bill Young on March 05, 2009, 04:33:22 PM
I'm sure I've read a pretty detailed posting by Theo, some time ago, on how to do bellows retaping (like, how many folds to do at a time), but I can't find it. I'd like to read it again to see whether it's something I want to attempt. Could someone please provide a pointer to the item? Or maybe it was on the old forum?

Grateful for any help.
Title: Re: Re-taping Bellows
Post by: rileycat on March 05, 2009, 05:01:15 PM
Hi Pete
If it is any help and not too late, Charlie Marshall - CGM Musicals - does a good pot of specific bellows tape glue, which can be easily spread by finger and which "grips" and dries quite easily as long as you don't try to do too many folds at a time. I'd keep off the PVA, white-glue stuff as it lacks the "grip" and seems messy in use when compared with the "proper" stuff. However, whatever you use, as others have said, take your time, cut very carefully and keep the folds clean.
Tony
Title: Re: Re-taping Bellows
Post by: nomad on May 08, 2011, 09:52:58 PM
Hi

I am going to have a go at my first ever bellow repair. I need to replace some metal corners which will involve adding tape to the bellows.

So i have a few questions.

1) Do you renew the bellow tape down the full length of the bellows or do you just take it back a couple of inches and replace a small section.

2) If only replacing a sectin do you slightly overlap the original remaining tape

3)My bellow tape is 3/4" if i was to renew the full length would i be better using 1" bellow tape to cover any old glue lines.

4)Are metal bellow corners easy to fit.

Any tips on any of the above will be most welcomed,

Thanks
Title: Re: Re-taping Bellows
Post by: Lester on May 08, 2011, 10:35:04 PM
1) Do you renew the bellow tape down the full length of the bellows or do you just take it back a couple of inches and replace a small section.

I would replace the whole length, which would probably drive me to replace all the tape on the bellows so it matched  ;)

Quote
2) If only replacing a sectin do you slightly overlap the original remaining tape

See above or butt the repair to the old tape.

Quote
3)My bellow tape is 3/4" if i was to renew the full length would i be better using 1" bellow tape to cover any old glue lines.

I would use 3/4"

Quote
4)Are metal bellow corners easy to fit.


Not that difficult, I use contact adhesive and big pliers, more info here  Search is your friend  ;D (http://forum.melodeon.net/index.php/topic,6498.0.html)

Title: Re: Re-taping Bellows
Post by: nomad on May 08, 2011, 11:52:20 PM
Thanks for the reply Lester, deep down I sort of knew the correct thing to do was the renew the full length, and I will do all the bellows.

Thanks
Title: Re: Re-taping Bellows
Post by: dahlberg on August 09, 2011, 07:24:36 AM
*bump*
Half way thru re-taping the Granesso i discovered there is a huge leak closest to the frame.
How to solve this?
What about glue a strip of paper from inside?

(edit:added pic)
Title: Re: Re-taping Bellows
Post by: Keithypete. on August 20, 2012, 09:58:49 AM
Do I need to remove 100 % of the old, gold Pokerwork paper? Most of it has come away cleanly, but some is hanging on, the top layer having peeled off leaving the half with the glue.
Does the extra thickness of the tape cause any problems?
Title: Re: Re-taping Bellows
Post by: Lester on August 20, 2012, 10:15:40 AM
I would, a gentle dampening will normally free it up
Title: Re: Re-taping Bellows
Post by: Rob2Hook on August 20, 2012, 12:59:29 PM
I know this perhaps addressing advanced techniques (and I haven't even attempted the basics)...  I had the back and bottom of the bellows on a Club IIB Victoria retaped by a professional (Hohner trained), actually I'd only asked him to retune.  He has used ribbed black Italian tape and unlike on a new set of bellows, the alignment of the ribbing makes a random pattern rather than the immaculate diagonal one has come to expect.  If I eventually get round to taping the other two, more visible sides do I just have to accept that the ends may not be perfectly aligned so as to get the pattern established - or does one faff about working out how to cut the pieces against a guage to achieve a perfect result?

I guess its a choice between a long, boring but simplish job or a longer, more frustrating job to get the alignment.  Might even consider an insert pattern in gold if going to all the trouble!

Perhaps I should just send the measurement to the niece's in-laws in Port Recanati...

Rob.
Title: Re: Re-taping Bellows
Post by: Keithypete. on August 20, 2012, 01:04:16 PM
OK. Judicial use of a cotton bud did the trick.

Now to go in gently to remove the the bits tucked in next to the bellows frames. Some of the Orange has come away in a few places too. I think I will be able to touch it up with paint of one sort or another. I may paint the whole lot a different colour. Has anyone tried this? What are the options?
Title: Re: Re-taping Bellows
Post by: Lester on August 20, 2012, 01:07:00 PM
I know this perhaps addressing advanced techniques (and I haven't even attempted the basics)...  I had the back and bottom of the bellows on a Club IIB Victoria retaped by a professional (Hohner trained), actually I'd only asked him to retune.  He has used ribbed black Italian tape and unlike on a new set of bellows, the alignment of the ribbing makes a random pattern rather than the immaculate diagonal one has come to expect.  If I eventually get round to taping the other two, more visible sides do I just have to accept that the ends may not be perfectly aligned so as to get the pattern established - or does one faff about working out how to cut the pieces against a guage to achieve a perfect result?

I guess its a choice between a long, boring but simplish job or a longer, more frustrating job to get the alignment.  Might even consider an insert pattern in gold if going to all the trouble!

Perhaps I should just send the measurement to the niece's in-laws in Port Recanati...

Rob.

I don't attempt to align the pattern  and I don't know I have ever seen is done but it is important to make sure all the tape runs in the same direction otherwise it looks really poor. As I cut the tape I mark the free end and I mark the bellows so it is easy to ensure the orientation.
Title: Re: Re-taping Bellows
Post by: Lester on August 20, 2012, 01:09:52 PM
OK. Judicial use of a cotton bud did the trick.

Now to go in gently to remove the the bits tucked in next to the bellows frames. Some of the Orange has come away in a few places too. I think I will be able to touch it up with paint of one sort or another. I may paint the whole lot a different colour. Has anyone tried this? What are the options?

I have a tester can of Dulux emulsion to do odd touch ups. Take your bellows to B&Q and they can scan the colour to generate a match pot. I have also repainted whole bellows using the same paint, takes a deal of preparation though.
Title: Re: Re-taping Bellows
Post by: Keithypete. on September 02, 2012, 11:14:30 AM
I got some bellows tape from CGM, along with the appropriate glue. Also in the parcel was a sheet of paper with tips on how to do the job properly. As with most things it's all in the preparation.

The glue is queer old stuff & to be honest I had no faith in it, having never used it before, but it is actually very good. The gluing & putting on of the tape can be quite quickly done, once the prep and set up is out of the way.

About half done now.
Photos to follow when I have done the other half.
Title: Re: Re-taping Bellows
Post by: malcolmbebb on September 02, 2012, 12:06:09 PM

I have a tester can of Dulux emulsion to do odd touch ups. Take your bellows to B&Q and they can scan the colour to generate a match pot. I have also repainted whole bellows using the same paint, takes a deal of preparation though.
Just curious - how durable has this proven to be? And what preparation do is needed, apart from the obvious cleaning and de-fluffing?
Malcolm
Title: Re: Re-taping Bellows
Post by: Lester on September 02, 2012, 02:03:17 PM
Seems to last OK. Did nothing other than clean out the fluff prior to slapping it on.
Title: Re: Re-taping Bellows
Post by: AirTime on September 15, 2012, 05:18:00 PM
I still can't get my head around the fact that Hohner uses a tape for the Poekerworks/Ericas bellows that seems singularly ill-suited to its purpose. The gold rubs off because there is absolutely no coating to protect it, or the underlying tape. The old buckram tape is far superior in this respect.

Having said that, I'm not sure I see the necessity of striping the old tape - it is so thin that a second layer doesn't seem to have any effect on the performance of the bellows. I've noticed that with the old Buckram tape, taping over the old tape seems to works well as it sticks over the old tape well enough & can then later be peeled off the underlying tape without damaging the bellows material. I doubt this would work as well with the gold tape, however, as it will just take bits of the underlying tape with it, leaving an irregular mess.

What about coating the gold tape with some sort of finish to increase it's resistance to rubbing?
Title: Re: Re-taping Bellows
Post by: Adam-T on September 15, 2012, 05:33:12 PM
Hohner used to use decent tape and probably still do on German made instruments -a three year old Corona II classic is the newest German Hohner I`ve encountered, the tape was fine

but I also can`t see the point of going to the trouble of glueing on the cheap bogpaper they use on the chinese made ones, surely decent stuff doesn`t cost that much more given the price of the boxes (we`re hardly talking £10 toys here) .. lets face it, it`s not Hohner who`ll get the repair work of replacing the tape anyway and all it does is naff people off that they had to do it within a year of buying the thing..
Title: Re: Re-taping Bellows
Post by: AirTime on September 16, 2012, 12:26:02 AM
The gold tape was definitely used on German-made boxes ( I don't know how long for) before they switched production to China.

The (only) reason to use the terrible gold tape is to match the existing tape, if (as is likely) only a small part of the tape is damaged.
Title: Re: Re-taping Bellows
Post by: Adam-T on September 16, 2012, 07:39:50 AM
Yep, I`ve got German boxes with it on but even the late German gold tape was far better than the Chinese bogpaper . Charlie Marshall has non ribbed gold tape which is as good as his usual Italian stuff, I don`t know if it matches Hohners chinese bogpaper as I no longer have the chinese pokerwork but it`s worth an ask.
SimplePortal 2.3.5 © 2008-2012, SimplePortal